Megger

MeggerMultimeter Test Lead 1001-883 Test Lead Kit, CAT IV 300 V　6231-592

Instructions, mains plug test leads, 3-wire test lead set with crocodile clips, 8 x AA alkaline batteries, neck strap. LT310 ; 320 Non Tripping Loop Tester Accessories. Two non-tripping loop impedance testers that comply with EN61557 part 3 for testing, measureing or monotoring of protective measures. RCDs rated 30mA or greater are not tripped, even electronic RCDs 3-wire low current non tripping loop test measure 0.01Ω to 2kΩ (autoranging) with resolution 0.01Ω up to 10Ω Two wire high -current test is selctable where RCD connection is not an issue 1A to 23kA prospective fault current (PSCC) display LED indication of correct supply and test lead connection 3-phase safe - will not be damaged if connected across phases 100V to 280V suitable for single-phase testing Supply voltage measurement range Clear 20mm high digit LCD display with analogue arc bargraph Tough rubber armoured case with self contained cover that locks away underneath the instrument during use Designed to hang comfortably around the neck when in "hands free" use Easy-to-use with colour coded ranges to help in the test range selection Safety input terminal interlock - prevents unsafe connection of test leads Safety lockout prevents the test from operating when the circuit voltage is >280V (LT310) or >480V (LT320) Meets the requirements of BSEN 61010-1 for safe connection t a 440V Installation Category III supply (300V Phase to Earth) Weatherproof to IP54. LT320 model additional features:. 50V to 480V operating range allows single and three-phase testing 25Hz to 450Hz frequency measurement range Phase rotation indicator Max Zs display R1+R2 is calculated and displayed Backlit display and range selection ideal for low light environments

Megger

Megger 1007-157 Insulation Tester Probe, For Use With MIT480　1007-157

Hard carry case, rubber boot with stand, silicone test lead set, SP5 remote switch probe, 5 off AA alkaline batteries & instructions (CD-ROM). MIT480 Series Telecom Insulation & continuity test. Telecommunication insulation and continuity testers developed to meet the special requirements of telephone line testing, as well as the requirements of electrical contractors and industrial testing to CATIV 600V. All instruments meet TNV3 as well as IEC1010, HD384 and BSEN61557. The insulation test inhibit voltage has been raised to 75V to overcome interference between cables experienced at lower voltages, compared to 50V for standard cable testing. All models: Complies with EN 61010-1 CATIV 600V safety rating 200mA & 20mA Continuity testing Insulation test voltage display 75V test inhibit TRMS and DC Voltage measurement Dual Digital Display and Analogue bar-graph Alkaline or NiMH rechargeable battery operation IP54 weatherproof housing Test lock allows the insulation test to be held on indefinitely MIT480 specific features 50V & 100V insulation testing 100Gohms insulation range. MIT481 additional features 50V, 100V, 250V, 500V, 1000V insulation tests 200Gohms insulation range Leakage current display kΩ resistance measurement Timer, PI and DAR insulation tests Insulation limit alarms 0.1nF to 10uF Capacitance measurement Cable length calculated from an adjustable cable capacitance reference (default 50nF/km). Test result storage (>1000) MIT485 additional features Result download Bluetooth capability (requires Bluetooth enabled PC or USB plus Bluetooth adaptor)

Megger

Megger DH5 Ohm Meter　1006-445

DLR010 Replacement Handspike Lead Sets. Duplex handspikes with sprung loaded tips. Maximum current capacity 10 A. 6mm spacing between ips on each probe. DH5 2.5m Duplex handspikes (2 off), one with indicator lights. Compatible with the Megger DLRO10X & DLRO10HD ohmmeters

Megger

Megger 1006-408 Electrical Installation Tester Case, Accessory Type Test & Carry Pouch, For Use With MFT1731 On-Site　1006-408

Megger Carry Pouch for MFT1700/1800 Series. Meggers padded carry case for use with MFT1700 and MT1800 series of testers. Manufactured from a hard wearing nylon fabric, featuring a main compartment, pocket under the lid for test leads and an external pocket for cables and accessories. Features and Benefits. Soft padded carry case. Nylon fabric. Internal pocket for storage

Megger

Megger 1007-463 Electrical Installation Tester Case, Accessory Type Large Soft Pouch with Extra Storage, For Use With　1007-463

Megger Large Pouch for MFT1700/1800 Series. Megger's carrying pouch with shoulder strap for use with MFT 1700 and MFT1800 series of testers. The case is able to house your installation tester and accessories, among other equipment. The main compartment is divided by flexible walls into five compartments which can be simply and quickly removed. The pouch has two side pockets which can store further accessories and the reinforced base is equipped with four non-slip rubber feet. Features and Benefits. External Dimensions: 30 x 24 x 21 cm (W ;font face="symbol">´ ;/font> D ;font face="symbol">´ ;/font> H). Flexible Storage Options. Reinforced base

Megger

Megger DET3TC Earth & Ground Resistance Tester 2kΩ CAT IV 100 V　DET3TC

EN61010-1 CAT IV 150V & CAT III 300V. 2 earth test stakes, 3 connection leads, 8 x AA alkaline batteries, hard carry case, quick start guides, user guide on CD. DET3TC 3 Pole Earth Tester. 3 pole earth tester for measuring the resistance of earth rods and associated installations.,An ICLAMP selective earth clamp is available separately, and when used with the DET3TC allows the testing of an earth rod without the need for disconnection from the system. Resistance range 0.01 to 2000 ohms auto ranging Choice of 2 or 3 terminal measurements Simple one button operation Superior noise rejection to 40V pk-pk Measures earth voltage 0 – 300V Automatic P spike & C spike check Clamp input for no-disconnect testing (requires ICLAMP) Earth current range (with ICLAMP up to 19.9A)

Megger

Megger 1007-165 Portable Appliance Tester Lead, For Use With PAT 350, PAT 450　1007-165

User Guide CD, extension lead adaptor, quick-start guide, carry case and document wallet, IEC C6 to C13 plug adaptor, bond/continuity test lead with croc-clip and probe, High Voltage probe(PAT450 only). PAT400 Series Downloading PAT Testers (GB) ; Accessories. Large 5.7in. VGA backlit colour screen for clear ; easily understandable results 5 user defined soft-keys for direct access to frequently used functions Full QWERTY keypad for easy and precise data entry. 10,000 record memory for interruption-free testing. USB port for quick download to a memory stick eliminating the need to take the tester back to the office every night, data is directly compatible with Megger PowerSuite software. 2 USB ports for optional barcode reader ; printer Selectable PASS/FAIL limits provide instant indication of a faulty asset 200 mA continuity test 250 V and 500 V insulation tests prevents damage to sensitive electronics Instant re-start for fast testing across multiple rooms Tests for standard, RCD-protected and anti-surge extension leads Interrupt-time tests for portable or plug-in RCDs Adjustable test times allow faster testing for increased productivity Differential, Substitute or Touch leakage current tests Operational test with VA display. PAT410 Features:. Light weight, low current Portable Appliance Tester, configurable for fast testing and high productivity. 230V operation ; testing. PAT420 Features:. Dual 230V and 110V operation and testing for industrial, commercial and residential applications 10A and 25A bond test with high duty cycle and no overheating on repetitive tests. PAT450 Features:. Dual 230V and 110V operation and testing for industrial, commercial and residential applications 10A and 25A bond test with high duty cycle and no overheating on repetitive tests Flash test at 1.5kV and 3kV, ideal for industrial, tool hire and service workshops. Software Package - Basic FormFiller Certification. Operators can access and download for free the software package from Megger via the web site. Offering users a quick and simple solution to create and store standard IET certification forms and PAT certificates. Suitable for use on Windows® platforms running JAVA 8. FormFiller provides a simple, intuitive form completion tool, allowing professional printed certificates and documentation to be produced with negligible software skills. All certificates and forms can be stored within the application or exported in PDF form. Features. Simple operational interface. Storage of completed forms with retrieval by certificate type or client. PDF export facility for safe and simple distribution. Multi-page Schedules for testing larger installations. Drop down fields to speed up certificate completion

Megger

Megger DET14C Earth & Ground Resistance Tester 1.5kΩ CAT IV 600 V　1000-761

(DET14C & DET24C):Carry case carry strap , User guide on CD, calibration check accessory, 4 x AA alkaline batteries. (DET24C only): USB IrDA dongle, USB lead & PowerDB lite software. Megger 1007-331 ( < 910-6810') 910-6810/ ) is a Bluetooth version of Megger 1000-762 ( < 705-9431') 705-9431/ ). DET14C & DET24C Earth Test Clamp. Ground resistance range : 0.050 Ω to 1500 Ω True RMS Ground leakage current range : 0.2 mA to 35 A Auto ranging & HOLD function 4 digit plus 6 digit backlit LCD display High and low resistance alarms 256 test results storage & recall Real time date & time stamping of results Oval clamp for easy access to earth cables & earth straps 37mm dia conductor & 50mm earth strap capacity Low maintenance flat jaw interface EN61010 Safety rating CATIV 600V Extended battery life. DET24C Additional Features. IrDA to USB interface for download 2000 test results storage PowerDB LiteTM software

Megger

Megger Terminal Adaptor Kit for TDR2000/3 Handheld TDR　1003-218

Terminal Adaptor Kit. Terminal adaptor kit for TDR2000/3 Cable Fault Locator.

Megger

Megger 1001-561 Voltage Indicator Proving Unit 50 → 690V LED　1001-561

Megger

Megger DET3TD Earth & Ground Resistance Tester Kit　DET3TD

Megger

［Discontinued］Megger 1002-001 Insulation Tester Lead, For Use With BM100　LEADS - ATR

Durable hard carry case, silicone test lead set, AA alkaline batteries & instructions. RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty. MIT400 Series Digital Insulation & Continuity Testers. All instruments meet IEC1010, HD384 and BSEN61557, and are sealed to IP54 for weatherproof performance. Easy to hold and comfortable to use, the large display provides the unique combination of two digital readouts and an analogue arc. All primary results are displayed in the larger digital display and repeated on the analogue arc. Additionally, auxiliary test information such as frequency, leakage current, Insulation or `circuit voltage etc is displayed in the smaller secondary digital display. Rubber over-moulding combines the tough shock absorbing outer protection with excellent grip, on a strong modified ABS housing, providing an almost indestructible case. Battery requirements are 5 AA batteries of either standard Alkaline (supplied) or Nickel Metal Hydride (NiMH) rechargeable type. All models feature:. Insulation testing to 1000V with Insulation test voltage display Continuity testing at 200mA down to 0.01ohms Alternative 20mA test current AC/DC Voltage measurement True RMS Measurement to 600V 50V Live circuit test inhibit Complies with EN61010-1 CATIV 600V IP54 weatherproof housing Hard carry case Optional SP5 switched probe with remote test button for single-handed operation

Megger

［Discontinued］Megger 1002-001 Electrical Installation Tester Lead, Accessory Type Lead, For Use With MIT 400 Series, MIT 410 Series　6220-437

Durable hard carry case, silicone test lead set, AA alkaline batteries & instructions. RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty. MIT400 Series Digital Insulation & Continuity Testers. All instruments meet IEC1010, HD384 and BSEN61557, and are sealed to IP54 for weatherproof performance. Easy to hold and comfortable to use, the large display provides the unique combination of two digital readouts and an analogue arc. All primary results are displayed in the larger digital display and repeated on the analogue arc. Additionally, auxiliary test information such as frequency, leakage current, Insulation or `circuit voltage etc is displayed in the smaller secondary digital display. Rubber over-moulding combines the tough shock absorbing outer protection with excellent grip, on a strong modified ABS housing, providing an almost indestructible case. Battery requirements are 5 AA batteries of either standard Alkaline (supplied) or Nickel Metal Hydride (NiMH) rechargeable type. All models feature:. Insulation testing to 1000V with Insulation test voltage display Continuity testing at 200mA down to 0.01ohms Alternative 20mA test current AC/DC Voltage measurement True RMS Measurement to 600V 50V Live circuit test inhibit Complies with EN61010-1 CATIV 600V IP54 weatherproof housing Hard carry case Optional SP5 switched probe with remote test button for single-handed operation

Megger

［Discontinued］Megger 1002-001 Loop Impedance Tester 2 Wire Test Lead Set, For Use With MIT 300 Series　1002-001

instructions, 2 wire test lead set with crocodile clips, 8 x AA alkaline batteries, neck strap ; carry case. RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty. 3. MIT 300 Series Insulation ; Continuity Testers. A range of insulation testers that meet the relevant requirements of EN61557, BS7671, HD 384, IEC 364 and VDE 0413 for applications in all aspects of electrical contracting, building maintenance, testing, inspection and servicing. 20mm LCD display with true analogue response Tough rubber armoured case with self contained display cover that locks away underneath the instrument during use Designed to hang comfortably around the neck for hands-free, or for bench use Automatic 200mA fast continuity test on connection to the circuit Lead resistance nulling on continuity allows for use of fused test probes Automatic discharge of circuit under test Safety input terminal interlock - prevents unsafe connection of test leads Intelligent Safety System - even if connected to a live circuit whilst on continuity setting the tester will remain safe and undamaged Live voltage warning alerts the operator when a circuit voltage over 25V exists when insulation testing Safety lockout prevents the test from operating when the circuit voltage is > 50V Continuity check - prevents a continuity test or buzzer test on a live circuit 3 phase safe - will not be damaged if connected across phases Locking test button Meets the requirement of BS EN 61010-1 for safe connection to a 440V Installation Category III supply (600V Phase to Earth) IP54. MIT310A. Moving coil display. MIT320 benefits from the following additional features:. Backlit display and range selection ideal for low light environment Selectable insulation alarm limit for fast go - no go testing Selectable continuity alarm limit for fast go - no go testing Resistance measurement range to 1 MΩ SP3 switched probe supplied for one handed operation SP1000 illuminated switched probe with ultra-bright LED light available separately

Megger

［Out of stock］Megger MIT230, Insulation Tester 999MΩ CAT III 300 V　MIT230

When measuring voltages, the use of fused test leads is recommended for personal safety. 6 x AA alkaline batteries, test leads, crocodile clips, carry case, instructions. RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty. 3. MIT230 Insulation ; Continuity Tester. The MIT230 incorporates a range of safety and operation features in one of the smallest electrical insulation testers available. Its LCD offers a combination of digital readout and analogue display, with an analogue pointer response for evaluating circuit charge and discharge characteristics. The instrument housing is in tough ABS. Features ; Benefits. Insulation testing to 1000 MΩ Dual ; triple test voltages models Digital display with electronic analogue arc display helps to confirm insulation condition ; to monitor fluctuating readings not apparent on the digital display Continuity testing at 200 mA down to 0.01 Ω resolution Automatic discharge of circuit under test 1 mA test current at selected voltage range Default voltmeter automatically switches in when the instrument is connected to a circuit with an AC or DC voltage greater than 25 V Auto-ranging analogue arc scale shows only the scale in use Live circuit warning above 25 V, also inhibits insulation ; continuity tests above 50 V Lead resistance compensation on continuity Hands free continuity testing Auto power-down after 5 min Complies with IEC 1010-1 safety standard installation Category III, 600 V phase to earth Conforms to EN61557-1 Tests to BS7671, 713-02, 713-03, 713-04, 713-06, 713-08, 413-04-04

Megger

［Discontinued］MeggerMultimeter Test Lead 1003-132 Test Lead Kit No, CAT IV 300 V　1003-132

Test lead set with crocodile clips, mains socket test lead, 8 AA alkaline batteries, hard carry case and instructions. RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty. 3. LTW 300 Series. Earth loop impedance testers to verify the loop impedance of a live electrical circuit without the need to disconnect the electrical supply. The LTW300 series instruments offer a safe and easy 2 wire loop testing solution that does not trip 30mA RCDs and can be used on a wide range of voltages. Backlit display 0.01Ω resolution No-trip loop test on circuits with RCDs of ≥30 mA 3 phase circuits with RCD protection can be tested Tests radial circuits where the circuit does not return to the origin, even where only a phase and neutral contacts are available. 10 second non trip loop test time with Auto test extension up to a further 10 seconds if noise is detected, to improve the accuracy of the test High current loop testing for supplies that do not have an RCD fitted AUTO START will start the loop test running as soon as the test leads are connected; no need to press the test button means much safer testing PFC Display up to 20kA Voltage and frequency measurement 110Vac systems including 110V centre tap to earth (55V phase to earth) can be tested on the secondary winding. IP54 Weatherproof case Optional 10A fused 2 wired test leads and crocodile clip set Complies with IEC61010-1 300V CATIV safety standard and meets EN61557

Megger

［Discontinued］Megger 1000-633 Electrical Installation Software, For Use With MFT1553　1000-633

System Requirements : Pentium IV PC running XP or Vista operating system; 128MB RAM (Min); 100MB hard disk space; CD-ROM drive; COM1 RS232 port (or USB port with USB to RS232 adaptor) for use with downloading PAT testers; Bluetooth for use with Megger MFT1553. Contractor PAT & Electrical Certification Software. Powersuite Professional Contractor offers all the features of PowerSuite Lite with the addition of a data based client, assets and results management database for managing 17th Edition electrical and Portable Appliance test results. All records and downloaded data is allocated to the appropriate customer on which a number of reports can be run. Work in real certificates and forms Client and results database manages links between customers and their test results Download test results from Megger downloading PAT testers, Megger downloading electrical installation testers and third party test equipment or direct data entry to certificates Real time results transfer via Bluetooth with Megger MFT1553 electrical installation tester Import company logo and add header page to customise certificates for a professional appearance Print on plain paper or pre-printed forms Extensive range of certificate formats and supports IEE, NICEIC, ECA, SELECT and ELECSA and BS electrical test certificates Full range of PAT testing certificates including repairs cerificates Reports module generates a wide range of reports for electrical installation testing and PAT testing. Project billing certificates and reports Digital imaging module allows picture import for increased clarity in reports Organiser module for scheduling workload, site work and retesting etc. with graphical diary Extended forms offer alternative and extra certificate formats including filling stations and security systems, ensuring there is a certificate to meet your requirements

Megger

［Discontinued］Megger 1001-975 Electrical Installation Tester Lead, Accessory Type 10 A Fused Test Lead Set with Prod & Clip, For Use　1001-975

Crocodile clips, large removable prods with GS38 probe tips, standard 4 mm plugs and built-in 600 V 10 A fast breaking fuses. Megger Three Wire Fused Test Lead Set. Megger three wire fused test lead set is the ideal replacement or spare test lead set for the Megger range of multi function testers. These GS38 compliant test leads are suitable for use with the Megger MFT1552, MFT1553, MFT1710, MFT1720 and MFT1730. Features and Benefits. GS38 compliant. Length: 1.2 m. CAT III 1 kV rated with the safety probes. CAT III 600 V rated when using the crocodile clips

Megger

［Discontinued］Megger AVO830 Handheld Digital Multimeter, 10A ac 600V ac 10A dc 600V dc　1008-722

Megger AVO830 True RMS Digital Multimer. Megger AVO830 True RMS Digital Multimeter is designed for professional electricians and engineers. The 10000 Count AVO830 offer a wide range of functions. The AVO830 has an AC-DC voltage range up to 600 V and a maximum current range of 10 A AC-DC. The meters have an innovative input impedance selection. In high mode prevents loading of the circuit under test while the low mode collapses any capacitive coupled (ghost) voltages which correctly identify an isolated circuit. Extra ranges are resistance (50 MΩ), conductance (60 ns), capacitance (10000 μF) and diode. The AVO830 have high frequency interference filtering, phase rotation indication from 90 V ac to 440 V ac and non-contact voltage detection. Measurement tools include MIN/MAX, average, hold and auto hold. Safety compliance to IEC61010 is CATIV 600 V. Features and Benefits. IP54 environmental protection. Phase rotation. High / Low sensitivity live circuit detection. 10 MΩ / 10 kΩ input impedance. MIN / MAX / AVG / Smoothing. TRMS Voltage and current measurement. Dual digital readout. Classic Megger analogue arc. 0.1% Basic accuracy. 10 000 Count resolution 4 1/2 digits. Phase sequence measurement for 3 phase circuit and motor testing. 10 mΩ and 10 kΩ input impedance switching

Megger

［Discontinued］Megger AVO835 Handheld Digital Multimeter, 10A ac 1000V ac 10A dc 1000V dc　1008-721

Megger AVO835 True RMS Digital Multimer. Megger AVO835 True RMS Digital Multimeter is designed for professional electricians and engineers. The 10000 Count AVO835 offer a wide range of functions. The AVO835 has an AC-DC voltage range up to 1000 V and a maximum current range of 10 A AC-DC. The meters have an innovative input impedance selection. In high mode prevents loading of the circuit under test while the low mode collapses any capacitive coupled (ghost) voltages which correctly identify an isolated circuit. Extra ranges are resistance (50 MΩ), conductance (60 ns), capacitance (10000 μF) and diode. A temperature range from -40°C to 400°C is also featured on the AVO835. The AVO835 have high frequency interference filtering, phase rotation indication from 90 V ac to 440 V ac and non-contact voltage detection. Measurement tools include MIN/MAX, average, hold and auto hold. Safety compliance to Safety compliance to EN 61010-1 1000 V CAT III / 600 V CAT IV. Features and Benefits. IP54 environmental protection. Phase rotation. High / Low sensitivity live circuit detection. 10 MΩ / 10 kΩ input impedance. MIN / MAX / AVG / Smoothing. TRMS Voltage and current measurement. Dual digital readout. Classic Megger analogue arc. 0.1% Basic accuracy. 10 000 Count resolution 4 1/2 digits. Phase sequence measurement for 3 phase circuit and motor testing. 10 mΩ and 10 kΩ input impedance switching

Megger

［Out of stock］Megger DCM300E Clamp Meter, Max Current 300A ac CAT II 600 V, CAT III 500 V　DCM300E

Batteries, instruction manual, carrying case. AVO DCM 300E. Fully IEC1010-1 and IEC101-2-032 compliant for circuits up to 500V phase to phase or 300V phase to earth CAT III or 600V CAT II 30mA and 300mA ranges for leakage current measurement 0.01mA resolution on 30mA range 30A and 300A ranges for power measurements Data hold facility Maximum conductor size 40mm diameter 3200 count LCD display with analogue bar graph

Megger

［Discontinued］Megger 1001-874 Electrical Installation Tester Lead, Accessory Type Lead, For Use With CM500　1001-874

Replacement 2 wire mains lead for Megger CM400 AND CM500 installation testers

Megger

［Out of stock］Megger MIT220, Insulation Tester 999MΩ CAT III 300 V　MIT220

When measuring voltages, the use of fused test leads is recommended for personal safety. 6 x AA alkaline batteries, test leads crocodile clips, carry case & instructions. RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty. MIT220 Insulation & Continuity Tester. The MIT200 is one of the smallest insulation testers available on the market today. With options of a two voltage tester to a three voltage instrument, the MIT200 instruments offer a range of safety and operation features.. Insulation testing to 1000MΩ Dual & triple test voltages models Digital display with electronic analogue arc display helps to confirm insulation condition & to monitor fluctuating readings not apparent on the digital display Continuity testing at 200mA down to 0.01ohms resolution Automatic discharge of circuit under test 1mA test current at selected voltage range Default voltmeter automatically switches in when the instrument is connected to a circuit with an AC or DC voltage greater than 25V Autoranging analogue arc scale shows only the scale in use Live circuit warning above 25V, also inhibits insulation & continuity tests above 50V Lead resistance compensation on continuity Hands free continuity testing Auto power-down after 5 minutes Complies with IEC 1010-1 safety standard installation Category III, 600V phase to earth Conforms to EN61557-1 Tests to BS7671, 713-02, 713-03, 713-04, 713-06, 713-08, 413-04-04

Megger

［Discontinued］Megger DLRO10HD 6V Sealed Lead-Acid Ohm Meter, Maximum Resistance Measurement 2500 μΩ, Resistance Measurement　1006-603

DH4 duplex handspikes with 1.2m lead length, test lead pouch (lid mounted) user guide on CD ,6V 7Ah sealed lead acid battery (fitted). DLRO10HD Heavy Duty 10A Low Resistance Ohmmeter. Heavy duty low resistance ohmmeter combining rugged construction with accuracy and ease of use. It features an internal rechargeable battery and can also operate from a mains supply, even if the battery is completely flat. 2 high power ( up to 25W) ranges ideal for inductive applications, and where heating a potential weakness is desirable 7 low power output ranges limited to 0.25W to avoid heating the test piece and to extend battery life. Rechargeable battery or line power supply, continuous operation, even with dead battery 10 A for 60 seconds, less time waiting to cool, great for charging inductance High input protection to 600 V, inadvertent connection to line or UPS voltage will not blow a fuse Heavy duty case: IP 65 lid closed, IP54 operational (battery operation only) Large backlit LCD is clear and easy to read in all lighting conditions. Rotary switch selects one of five test modes, including auto start on connection, giving ease of use. DH5 straight duplex handspike set with 2.5m long leads. See stock no. ; 666-7371 666-7371. Support accessories:

Megger

［Discontinued］Megger 1004-183 Battery Charger, For Use With MIT400/2 Insulation Tester　1004-183

MIT4XX mk2 Series Charging Options. Car charging options for use with the MIT4XX/2 Series of Insulation and continuity testers. 12 V dc car charger (requires mains charger kit) for use with MPN 1004-183 Mains charger kit (MIT 430/2 only) for use with MPN 1007-464

Megger

［Discontinued］Megger AVO210 Digital Multimeter, 10A ac 750V ac 10A dc 1000V dc　1006-969

Megger

［Discontinued］Megger AVO410 Digital Multimeter, 10A ac 750V ac 10A dc 1000V dc　1001-613

Megger

［Out of stock］Megger DCM1500 Clamp Meters, Max Current 1.5kA ac, 1.5kA dc CAT IV 600 V　1005-572

Megger

［Out of stock］Megger DCM310 Clamp Meters, Max Current 400A ac CAT III 600 V　1000-303

Megger

［Out of stock］Megger DCM320 Clamp Meters, Max Current 400A ac CAT III 600 V　1000-304

Megger

［Discontinued］Megger DCM330 Clamp Meters, Max Current 200A ac CAT III 1000 V, CAT IV 600 V　1000-219

Megger

［Out of stock］Megger DCM340 Clamp Meters, Max Current 600A ac, 600A dc CAT III 600 V　1000-305

Megger

［Discontinued］Megger VF3 Non Contact Voltage Indicator　2004-780

Megger

［Discontinued］Megger TPT320 Voltage Indicator with RCD Trip Test Continuity Check CAT IV 600 V　1004-304