STS Corporation

Đánh dấu laser (Số mô hình: mL 7010)　ML-7010

The laser line is irradiated to position the work process.
Uses a 10 mW high-brightness laser element.

STS Corporation

Đánh dấu laser (đường chéo, số mô hình: mLX2)　ML-X2

A cross laser line is emitted by one device.
Since it uses a 10 mW laser element, it emits bright laser lines.

STS Corporation

Endscope công nghiệp IES Dòng tip Hook TIP-12FK

STS Corporation

Ánh sáng với kiểm tra gương loại 1

STS Corporation

Máy đo độ ẩm DWM-190P

STS Corporation

Nhôm San lấp mặt bằng Rod TS-33 3 m 3 giai đoạn

STS Corporation

Cấp RS-40B Loại đai　RS-40B

This is a belt type level that emphasizes ease of use and durability.
It is a bubble tube that does not break easily.

STS Corporation

Dụng cụ đo độ nghiêng số học　DL164V

With LCD backlight, can be used in dark places.
When the main unit is upside down, the numbers are reversed to prevent misreading.

STS Corporation

Máy dò (Chỉ máy phân phối mực Laser màu xanh lá cây) SS 30 g

STS Corporation

Máy dò mực laser dọc OLP-2　OLP-2

Magnet dampers are used to stop the laser point quickly.
Built in a wide range of automatic correction mechanisms (± 4.5 °), it has a safe design with a buzzer sound warning when not correcting.

STS Corporation

Laser mực ra cho máy dò SS-50Z (kẹp)　SS-50Z

It is a special receiver for red laser marking, and the detection distance is about 50 meters maximum.
It is 19 mm thin and fits in the chest pocket.

STS Corporation

Thang máy laser 3 chân EL-CM

STS Corporation

Thang máy Laser 3 chân 160-278mm 2 giai đoạn

STS Corporation

Xoay laser cấp H600 (chân máy)　STS-H600

Just put it down, it's fully automatic alignment.
Corresponds to JIS laser safety standards. Irradiation direction selection blocking mode is installed.

STS Corporation

Cài đặt độ dốc Chức năng với mức laser xoay SLH-600　SLH-600

You can set the slope directly numerically on two axes, not only horizontal.
The remote control can set and check the slope from a distance from the main unit by two-way communication. (Approx. 100 m)

STS Corporation

Xoay Aspect Mức laser xanh GSL-VH10　GSL-VH10

It uses a green laser that is five times brighter (our company ratio) than a red laser.
Shoots a 360° laser with almost no breaks.

STS Corporation

Bộ điều khiển máy đơn giản cuộn HS-240C　HS-240C

This is a very simple inexpensive machine control with a longer light receiving width than a normal rotating laser level receiver and a wide angle detection direction.
Can be attached to both heavy equipment and staff (shaku).

STS Corporation

Bộ điều khiển máy cuộn HS-360 SET　HS-360 SET

It can be attached to the waste sheet of heavy equipment such as a bulldozer and used in combination with a rotary laser level to control the construction height.
The finishing accuracy of the land fill and cut is greatly improved, and the construction period is shortened.

STS Corporation

Tự động cấp 24 lần

STS Corporation

Khảo sát cho máy bay chân máy-OT Φ35mm

STS Corporation

Túi lăng kính phản xạ Q1.5 inch d Set

STS Corporation

Máy dò trượt Scale Bar　SIB240

Positioning the receiver on the scale bar, which was difficult with the clamp of the receiver accessory, can be easily determined by sliding.
You can easily measure the difference in height by sliding the receiver.

STS Corporation

Mức độ tinh thần kỹ thuật số　ODL400M

You can zero set any angle. The measuring surface has a strong magnet and can be used on pipes due to the concave grooves.
When the main unit is upside down, the numbers are inverted to prevent misreading.

STS Corporation

Dụng cụ đo độ nghiêng số học　DL200V

Shock absorbing rubbers are placed on the left and right sides of the body.
It is equipped with a parameter mode that can be freely set according to the user's convenience, such as selecting the minimum number of digits and turning the operation sound ON/OFF.

STS Corporation

Máy dò mức Laser cho máy dò HD-01　HD-01

It is a special receiver for red laser marking, and the detection distance is about 30 m maximum.
Lightweight compact body.

STS Corporation

机器控制器卷动WMC-3D远端显示RD-3d　RD-3D

By using the machine control WMC-3D, each indicator can be checked in the driver's seat of the heavy machine by wireless connection.
For civil engineering work, land leveling using heavy machinery such as bulldozers, and floor moats.

STS Corporation

我输入BOX Spirit Level　SV120VM

It has a magnet with a V-shaped measuring surface that is easy to install on a pipe.
Comes with an excellent impact protection rubber on both ends.

STS Corporation

我输入BOX Spirit Level　SV150VM

This V-shaped measuring surface is easy to install on top of the pipe and has a magnet.
Comes with an excellent impact protection rubber on both ends.

STS Corporation

我输入BOX Spirit Level　SV200VM

This V-shaped measuring surface is easy to install on top of the pipe and has a magnet.
Comes with an excellent impact protection rubber on both ends.

STS Corporation

Bộ điều khiển máy cuộn WMC-3D　WMC-3D

It can be attached to the waste plate of heavy equipment such as a bulldozer and used in combination with a rotary laser level to control the construction height. Moreover, it is possible to perform high-precision construction by displaying the slope of the left, right, up and down with a high-brightness LED indicator.
By using the optional remote display RD-3D, each indicator can be checked in the driver's seat of the heavy equipment by wireless connection.

STS Corporation

Key Holder loại tinh thần cấp　WS35P

Uses a white screen surface that is not affected by the color of the object to be measured and is easy to see bubbles.
Comes with a portable carabiner.

STS Corporation

Key Holder loại tinh thần cấp　WS35Y

Uses a white screen surface that is not affected by the color of the object to be measured and is easy to see bubbles.
Comes with a portable carabiner.

STS Corporation

Laser đánh dấu màu xanh lá cây GML-7010　GML-7010

The laser line is irradiated to position the work process.
Uses a 10 mW high-brightness laser element.

STS Corporation

Laser đánh dấu màu xanh lá cây (Cross Line) GML-X2　GML-X2

A cross laser line is emitted by one device.
Since it uses a 10 mW laser element, it emits bright laser lines.

STS Corporation

Nhôm chân máy ngắn JS-OTS　JS-OTS

This tripod is shorter than usual and is suitable for low position work.
Uses a square aluminum frame to enhance rigidity.

STS Corporation

Nhôm chân máy ngắn JS-ODS　JS-ODS

This tripod is shorter than usual and is suitable for low position work.
Uses a square aluminum frame to enhance rigidity.

STS Corporation

Chân máy ngắn bằng nhôm JS-OLS　JS-OLS

This tripod is shorter than usual and is suitable for low position work.
Uses a square aluminum frame to enhance rigidity.

STS Corporation

Cảm biến trở lại tường kỹ thuật số WBS -8652　WBS-8652

It is a multi-detector that can detect metal, wood, and current wires in walls.
Metal displays depth in centimeters.

STS Corporation

Vít đất chuyên dụng blade

STS Corporation

Dòng màu xanh lá cây Laser SRS-410G