SparkFun

LilyPadArduino328MainBoard　DEV-13342

SparkFun

Bus Pirate - v3.6a　TOL-12942

SparkFun

CAN-BUS Shield　DEV-13262

SparkFun

Jumper Wire Kit　PRT-00124

SparkFun

One Wire Digital Temperature Sensor - DS18B20　SEN-00245

SparkFun

Analog to Digital Converter - MCP3002　COM-08636

SparkFun

SparkFun USB to RS-485 Converter　BOB-09822

SparkFun

SparkFun LiPo Charger Basic - Micro-USB　PRT-10217

SparkFun

SparkFun Audio Jack Breakout　PRT-10588

The Audio Jack Breakout is a board for connecting a 3.5 mm audio jack. Five pins are pulled out, and can be connected to a breadboard or printed circuit board by soldering pin headers.

SparkFun

SparkFun Logic Level Converter - Bi-Directional　BOB-12009

SparkFun

Breadboard - Mini Modular (White)　PRT-12043

SparkFun

Raspberry Pi Camera Case - Black Plastic　PRT-12846

SparkFun

SparkFun Sunny Buddy - MPPT Solar Charger　PRT-12885

SparkFun

Battery Holder - 1x18650 (wire leads)　PRT-12899

SparkFun

Raspberry Pi GPIO Ribbon Cable -40 pin, 6inch (RPi2, B+)　CAB-13028

SparkFun

SparkFun Servo Trigger　WIG-13118

Servo Trigger is a board that allows easy control of RC servo motors such as small robots. The servo trigger of an external switch or logic signal can direct the connected servo motor to move from position A to position B. To use a servo trigger, use the onboard semi-fixed resistor to adjust the start/stop position and transition time.
An ATTiny84 microcontroller is used for control and a servo control program is executed. Each onboard servo trigger has three semi-fixed resistors. A sets the position where the servo enters when the switch is open, B sets the position where the servo moves when the switch is closed, and T sets the time it takes to return from A to B. There are two operating modes, which can be switched by the jumper (SJ1) on the back. The default is Bistable mode in which the switch is opened to A and closed to B. If the SJ1 is short-circuited, the switch is set to One shot mode in which AB and AB are repeated each time the switch is pressed.

SparkFun

SparkFun gamer:bit　DEV-14215

The gamer: bit is an expansion board for adding Famicom-like buttons and ports for external inputs. The edge connector makes it easy to connect to micro: bit. The left side of the board has a 4-way D-pad and the right side of the board has two action buttons. The two push buttons in the middle micro: bit act as Start and Select.
micro: bit is an ultra-small microcomputer board developed by the British Broadcasting Corporation (BBC) for the education of elementary school students.

SparkFun

micro:bit Battery Holder - 2xAA (JST-PH)　PRT-14299

SparkFun

LIDAR-Lite v3　SEN-14032

SparkFun

Mono Audio Amp Breakout - TPA2005D1　BOB-11044

SparkFun

SparkFun Safety Glasses　SWG-11046

SparkFun

Hydrogen Gas Sensor - MQ-8　SEN-10916

SparkFun

Arduino Pro Mini328-5V/16MHz　DEV-11113

The Arduino Pro Mini328-5 V/16 MHz is a minimalist Arduino board with a 16 MHz boot loader. The operating voltage of the microcomputer is 5V. It has a regulator and a clock oscillator, and the minimum operation of a microcomputer is possible, but it omits the USB interface that full-spec Arduino such as Uno has as a standard, and it has an external FTDI interface board. Auto reset is supported only when the DTR connector of the external interface is enabled. According to the manufacturer's comments, users should get started with Uno R3 and use the Arduino Pro after familiarizing themselves with the specifications. (Does the name "Pro" mean "no beginners" ...)

SparkFun

Arduino Pro Mini328-3.3V/8MHz　DEV-11114

The Arduino Pro Mini328-3.3 V/8 MHz is a minimalist Arduino board with an 8 MHz boot loader. The operating voltage of the microcomputer is 3.3 V, which is different from the standard 5 V. It has a regulator and a clock oscillator, and the minimum operation of a microcomputer is possible, but it omits the USB interface that full-spec Arduino such as Uno has as a standard, and it has an external FTDI interface board. Auto reset is supported only when the DTR connector of the external interface is enabled. The power supply voltage of the microcomputer is 3.3 V, so the voltage of the interface is also limited. According to the manufacturer's comments, users should get started with Uno R3 and use the Arduino Pro after familiarizing themselves with the specifications. (Does the name "Pro" mean "no beginners" ...)

SparkFun

MIDI Shield　DEV-12898

SparkFun

FTDI Basic Breakout - 5V　DEV-09716

Contents: USB to serial conversion board for ArduinoPro, mini and LilyPad with 5V supply voltage. Can be used with Arduinos that support automatic reset, eliminating the need to press the reset switch each time a sketch is written.

SparkFun

FTDI Basic Breakout-3.3V USB to Serial Adapter　DEV-09873

Contents: USB to serial conversion board for ArduinoPro, mini and LilyPad with 3.3 V supply voltage. Can be used with Arduinos that support automatic reset, eliminating the need to press the reset switch each time a sketch is written.
There are also products with 5V power supply voltage.

SparkFun

AruduinoPro328-3.3V/8MHz　DEV-10914

SparkFun

2mm 10pin XBee Socket　PRT-08272

SparkFun

XBee Shield　WRL-12847

Like Arduino Wireless Proto Shield and Arduino Wireless SD Shield, it provides logic level conversion between Arduino-XBee modules. (MOSFET) XBee radio module not included.

SparkFun

microSD Shield　DEV-12761

*Pin header is not included. Please purchase separately.

SparkFun

XBeeExplorerUSB　WRL-11812

This board enables USB connection of the XBee module to a personal computer. Equipped with a regulator IC to provide a 3.3 V power supply for the USB to Serial Conversion LSI, FT231X and XBee modules from 5 V USB bus power. It functions simply as a pitch conversion board which can be mounted on a 2.54 mm pitch breadboard, and all pins of the XBee module are connected to through holes for pin header mounting. (Pin headers are not implemented.) If you have this board, a mini-USB connection cable and a personal computer, you can set up with the X-CTU and run the XBee module.

SparkFun

SparkFun Transceiver Breakout - RS-485　BOB-10124

Breakout board to convert UART to RS-485

SparkFun

USB Type-C Breakout Board　BOB-15100

SparkFun

USB to RS232 Converter - 6ft　CAB-11304

SparkFun

MyoWare sensor cable with three electrode pads　CAB-12970

SparkFun

Back-Boost Converter Module　COM-15208

SparkFun

Arduino Uno- R3 SMD　DEV-11224

SparkFun

Pro Micro 3.3V/8MHz　DEV-12587

SparkFun

Pro Micro 5V/16MHz　DEV-12640