61-1375-21 小直径刀尖钻孔(Ultra MUSASHI,Φ9.4 x刀锋长度92 x全长127 mm,吸塑包装) PUMD-9.4
功能
- There is a small diameter drill at the tip part, and the circumferential blade performs end milling on the second stage, so even thin plate material or plastic resin does not break, and there is a clean hole without burring out the back.
- A new type of drill with a combination of a center ring drill and an end mill enables cutting at twice the speed of feed speed, resulting in higher efficiency.
- Work Material: Sheet Materials such as Aluminum, Steel, Resin, Rivet Hole, Pipe, H-Type Steel, Thick Plate.
规格
- 叶片直径 (mm) :9.4
- 长笛长度 (mm) :92
- 长度 (mm) :127
- 树干直径 (mm) :9.4
- 有效处理深度:3D (刀锋直径x 3倍)
- 高速钢 (HSS)
- 适用范围:工件:铝、钢、板材等树脂、铆钉制孔、管材、H型钢、厚度。
- 原籍国:日本
- 重量:53 g
- 制造商型号:PUMD94
- 代码编号:218-3170
封装大小：35×165×15 mm 60 g [关于封装大小]
| 第号命令。 | 61-1375-21 | |
|---|---|---|
| 型号号。 | PUMD-9.4 | |
| JAN代码 | 4957656490944 | |
| 标准价格 |
JPY: 3,020
USD: 18.93
Excange rate 1USD= 159.53JPY
Valid price in Japan |
|
| 数量 | 1piece | |
| 日本股票 |
|
|
| 供应商存货 |
|
|
产品种类 （尺寸不同·规格不同·选配品等）
| 产品图像 | 第号命令。 | 名称 | 型号号。 |
Blade diameter |
Groove length |
数量 | 标准价格 | 日本的有效价格 | 股票 [供应商存货] |
|
|---|---|---|---|---|---|---|---|---|---|---|
 |
61-1374-51 | 小直径刀尖钻孔(Ultra MUSASHI,Φ2.5 x刀锋长度35 x总长度61 mm,气泡套) PUMD-2.5 | PUMD-2.5 | 2.5mm | 35mm | 1piece | JPY: 540 | USD: 3.39 |
|
|
 |
61-1374-52 | 小直径刀尖钻孔(Ultra MUSASHI,Φ2.6 x刀锋长度37 x总长度64 mm,气泡套) PUMD-2.6 | PUMD-2.6 | 2.6mm | 37mm | 1piece | JPY: 590 | USD: 3.70 |
|
|
 |
61-1374-53 | 小直径刀尖钻孔(Ultra MUSASHI,Φ2.7 x刀锋长度37 x总长度64 mm,气泡套) PUMD-2.7 | PUMD-2.7 | 2.7mm | 37mm | 1piece | JPY: 590 | USD: 3.70 |
|
|
 |
61-1374-54 | 小直径刀尖钻孔(Ultra MUSASHI,Φ2.8 x刀锋长度39 x全长67 mm,吸塑包装) PUMD-2.8 | PUMD-2.8 | 2.8mm | 39mm | 1piece | JPY: 560 | USD: 3.51 |
|
|
 |
61-1374-55 | 小直径刀尖钻孔(Ultra MUSASHI,Φ2.9 x刀锋长度42 x总长度71 mm,气泡套) PUMD-2.9 | PUMD-2.9 | 2.9mm | 42mm | 1piece | JPY: 590 | USD: 3.70 |
|
|
 |
61-1374-56 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.0 x刀锋长度42 x总长度71 mm,气泡套) PUMD-3.0 | PUMD-3.0 | 3.0mm | 42mm | 1piece | JPY: 500 | USD: 3.13 |
|
|
 |
61-1374-57 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.1 x刀锋长度42 x全长71 mm,水泡包) PUMD-3.1 | PUMD-3.1 | 3.1mm | 42mm | 1piece | JPY: 680 | USD: 4.26 |
|
|
 |
61-1374-58 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.2 x刀锋长度42 x总长度71 mm,气泡套) PUMD-3.2 | PUMD-3.2 | 3.2mm | 42mm | 1piece | JPY: 610 | USD: 3.82 |
|
|
 |
61-1374-59 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.3 x刀锋长度45 x总长度73 mm,气泡套) PUMD-3.3 | PUMD-3.3 | 3.3mm | 45mm | 1piece | JPY: 610 | USD: 3.82 |
|
|
 |
61-1374-60 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.4 x刀锋长度45 x全长73 mm,薄膜包) PUMD-3.4 | PUMD-3.4 | 3.4mm | 45mm | 1piece | JPY: 640 | USD: 4.01 |
|
|
 |
61-1374-61 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.5 x刀锋长度45 x总长度73 mm,气泡套) PUMD-3.5 | PUMD-3.5 | 3.5mm | 45mm | 1piece | JPY: 610 | USD: 3.82 |
|
|
 |
61-1374-62 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.6 x刀锋长度48 x全长76 mm,吸塑包装) PUMD-3.6 | PUMD-3.6 | 3.6mm | 48mm | 1piece | JPY: 680 | USD: 4.26 |
|
|
 |
61-1374-63 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.7 x刀锋长度48 x总长度76公厘，气泡套) PUMD-3.7 | PUMD-3.7 | 3.7mm | 48mm | 1piece | JPY: 680 | USD: 4.26 |
|
|
 |
61-1374-64 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.8 x刀锋长度48 x全长76 mm,水泡包) PUMD-3.8 | PUMD-3.8 | 3.8mm | 48mm | 1piece | JPY: 670 | USD: 4.20 |
|
|
 |
61-1374-65 | 小直径刀尖钻孔(Ultra MUSASHI,Φ3.9 x刀锋长度51 x总长度79 mm,气泡套) PUMD-3.9 | PUMD-3.9 | 3.9mm | 51mm | 1piece | JPY: 740 | USD: 4.64 |
|
|
 |
61-1374-66 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.0 x刀锋长度54 x总长度83 mm,气泡套) PUMD-4.0 | PUMD-4.0 | 4.0mm | 54mm | 1piece | JPY: 670 | USD: 4.20 |
|
|
 |
61-1374-67 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.1 x刀锋长度54 x总长度83 mm,气泡套) PUMD-4.1 | PUMD-4.1 | 4.1mm | 54mm | 1piece | JPY: 810 | USD: 5.08 |
|
|
 |
61-1374-68 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.2 x刀锋长度54 x全长83 mm,水泡包) PUMD-4.2 | PUMD-4.2 | 4.2mm | 54mm | 1piece | JPY: 790 | USD: 4.95 |
|
|
 |
61-1374-69 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.3 x刀锋长度54 x全长83 mm,吸塑包装) PUMD-4.3 | PUMD-4.3 | 4.3mm | 54mm | 1piece | JPY: 810 | USD: 5.08 |
|
|
 |
61-1374-70 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.4 x刀锋长度56 x总长度86 mm,气泡套) PUMD-4.4 | PUMD-4.4 | 4.4mm | 56mm | 1piece | JPY: 810 | USD: 5.08 |
|
|
 |
61-1374-71 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.5 x刀锋长度56 x总长度86 mm,气泡套) PUMD-4.5 | PUMD-4.5 | 4.5mm | 56mm | 1piece | JPY: 790 | USD: 4.95 |
|
|
 |
61-1374-72 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.6 x刀锋长度56 x全长86 mm,水泡包) PUMD-4.6 | PUMD-4.6 | 4.6mm | 56mm | 1piece | JPY: 920 | USD: 5.77 |
|
|
 |
61-1374-73 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.7 x刀锋长度59 x总长度89公厘，气泡套) PUMD-4.7 | PUMD-4.7 | 4.7mm | 59mm | 1piece | JPY: 920 | USD: 5.77 |
|
|
 |
61-1374-74 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.8 x刀锋长度59 x全长89 mm,吸塑包装) PUMD-4.8 | PUMD-4.8 | 4.8mm | 59mm | 1piece | JPY: 920 | USD: 5.77 |
|
|
 |
61-1374-75 | 小直径刀尖钻孔(Ultra MUSASHI,Φ4.9 x刀锋长度62 x全长92 mm,薄膜包) PUMD-4.9 | PUMD-4.9 | 4.9mm | 62mm | 1piece | JPY: 990 | USD: 6.21 |
|
|
 |
61-1374-76 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.0 x刀锋长度62 x总长度92 mm,气泡套) PUMD-5.0 | PUMD-5.0 | 5.0mm | 62mm | 1piece | JPY: 890 | USD: 5.58 |
|
|
 |
61-1374-77 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.1 x刀锋长度62 x全长92 mm,吸塑包装) PUMD-5.1 | PUMD-5.1 | 5.1mm | 62mm | 1piece | JPY: 1,100 | USD: 6.90 |
|
|
 |
61-1374-78 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.2 x刀锋长度64 x全长95 mm,吸塑包装) PUMD-5.2 | PUMD-5.2 | 5.2mm | 64mm | 1piece | JPY: 1,050 | USD: 6.58 |
|
|
 |
61-1374-79 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.3 x刀锋长度64 x全长95 mm,水泡包) PUMD-5.3 | PUMD-5.3 | 5.3mm | 64mm | 1piece | JPY: 1,100 | USD: 6.90 |
|
|
 |
61-1374-80 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.4 x刀锋长度64 x总长度95 mm,气泡套) PUMD-5.4 | PUMD-5.4 | 5.4mm | 64mm | 1piece | JPY: 1,100 | USD: 6.90 |
|
|
 |
61-1374-81 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.5 x刀锋长度64 x全长95 mm,吸塑包装) PUMD-5.5 | PUMD-5.5 | 5.5mm | 64mm | 1piece | JPY: 1,050 | USD: 6.58 |
|
|
 |
61-1374-82 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.6 x刀锋长度67 x全长98 mm,水泡包) PUMD-5.6 | PUMD-5.6 | 5.6mm | 67mm | 1piece | JPY: 1,240 | USD: 7.77 |
|
|
 |
61-1374-83 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.7 x刀锋长度67 x全长98 mm,水泡包) PUMD-5.7 | PUMD-5.7 | 5.7mm | 67mm | 1piece | JPY: 1,240 | USD: 7.77 |
|
|
 |
61-1374-84 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.8 x刀锋长度67 x总长度98 mm,气泡套) PUMD-5.8 | PUMD-5.8 | 5.8mm | 67mm | 1piece | JPY: 1,240 | USD: 7.77 |
|
|
 |
61-1374-85 | 小直径刀尖钻孔(Ultra MUSASHI,Φ5.9 x刀锋长度67 x全长98 mm,薄膜包) PUMD-5.9 | PUMD-5.9 | 5.9mm | 67mm | 1piece | JPY: 1,300 | USD: 8.15 |
|
|
 |
61-1374-86 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.0 x刀锋长度70 x总长度102公厘，气泡套) PUMD-6.0 | PUMD-6.0 | 6.0mm | 70mm | 1piece | JPY: 1,190 | USD: 7.46 |
|
|
 |
61-1374-87 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.1 x刀锋长度70 x总长度102公厘，气泡套) PUMD-6.1 | PUMD-6.1 | 6.1mm | 70mm | 1piece | JPY: 1,400 | USD: 8.78 |
|
|
 |
61-1374-88 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.2 x刀锋长度70 x全长102 mm,吸塑包装) PUMD-6.2 | PUMD-6.2 | 6.2mm | 70mm | 1piece | JPY: 1,400 | USD: 8.78 |
|
|
 |
61-1374-89 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.3 x刀锋长度70 x总长度102 mm,吸塑包装) PUMD-6.3 | PUMD-6.3 | 6.3mm | 70mm | 1piece | JPY: 1,400 | USD: 8.78 |
|
|
 |
61-1374-90 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.4 x刀锋长度73 x全长102 mm,吸塑包装) PUMD-6.4 | PUMD-6.4 | 6.4mm | 73mm | 1piece | JPY: 1,400 | USD: 8.78 |
|
|
 |
61-1374-91 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.5 x刀锋长度73 x全长105 mm,吸塑包装) PUMD-6.5 | PUMD-6.5 | 6.5mm | 73mm | 1piece | JPY: 1,350 | USD: 8.46 |
|
|
 |
61-1374-92 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.6 x刀锋长度73 x总长度105 mm,气泡套) PUMD-6.6 | PUMD-6.6 | 6.6mm | 73mm | 1piece | JPY: 1,580 | USD: 9.90 |
|
|
 |
61-1374-93 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.7 x刀锋长度73 x全长105 mm,薄膜包) PUMD-6.7 | PUMD-6.7 | 6.7mm | 73mm | 1piece | JPY: 1,580 | USD: 9.90 |
|
|
 |
61-1374-94 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.8 x刀锋长度73 x全长105 mm,吸塑包装) PUMD-6.8 | PUMD-6.8 | 6.8mm | 73mm | 1piece | JPY: 1,580 | USD: 9.90 |
|
|
 |
61-1374-95 | 小直径刀尖钻孔(Ultra MUSASHI,Φ6.9 x刀锋长度73 x全长105 mm,薄膜包) PUMD-6.9 | PUMD-6.9 | 6.9mm | 73mm | 1piece | JPY: 1,660 | USD: 10.41 |
|
|
 |
61-1374-96 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.0 x刀锋长度73 x全长105 mm,吸塑包装) PUMD-7.0 | PUMD-7.0 | 7.0mm | 73mm | 1piece | JPY: 1,500 | USD: 9.40 |
|
|
 |
61-1374-97 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.1 x刀锋长度75 x全长108 mm,吸塑包装) PUMD-7.1 | PUMD-7.1 | 7.1mm | 75mm | 1piece | JPY: 1,890 | USD: 11.85 |
|
|
 |
61-1374-98 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.2 x刀锋长度75 x全长108 mm,吸塑包装) PUMD-7.2 | PUMD-7.2 | 7.2mm | 75mm | 1piece | JPY: 1,930 | USD: 12.10 |
|
|
 |
61-1374-99 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.3 x刀锋长度75 x总长度108 mm,气泡套) PUMD-7.3 | PUMD-7.3 | 7.3mm | 75mm | 1piece | JPY: 1,890 | USD: 11.85 |
|
|
 |
61-1375-01 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.4 x刀锋长度78 x全长111 mm,吸塑包装) PUMD-7.4 | PUMD-7.4 | 7.4mm | 78mm | 1piece | JPY: 1,890 | USD: 11.85 |
|
|
 |
61-1375-02 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.5 x刀锋长度78 x总长度111 mm,气泡套) PUMD-7.5 | PUMD-7.5 | 7.5mm | 78mm | 1piece | JPY: 1,730 | USD: 10.84 |
|
|
 |
61-1375-03 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.6 x刀锋长度78 x全长111 mm,吸塑包装) PUMD-7.6 | PUMD-7.6 | 7.6mm | 78mm | 1piece | JPY: 2,120 | USD: 13.29 |
|
|
 |
61-1375-04 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.7 x刀锋长度81 x全长114 mm,水泡包装) PUMD-7.7 | PUMD-7.7 | 7.7mm | 81mm | 1piece | JPY: 2,050 | USD: 12.85 |
|
|
 |
61-1375-05 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.8 x刀锋长度81 x全长114 mm,薄膜包) PUMD-7.8 | PUMD-7.8 | 7.8mm | 81mm | 1piece | JPY: 2,020 | USD: 12.66 |
|
|
 |
61-1375-06 | 小直径刀尖钻孔(Ultra MUSASHI,Φ7.9 x刀锋长度81 x全长114 mm,吸塑包装) PUMD-7.9 | PUMD-7.9 | 7.9mm | 81mm | 1piece | JPY: 2,120 | USD: 13.29 |
|
|
 |
61-1375-07 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.0 x刀锋长度81 x总长度114 mm,气泡套) PUMD-8.0 | PUMD-8.0 | 8.0mm | 81mm | 1piece | JPY: 1,850 | USD: 11.60 |
|
|
 |
61-1375-08 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.1 x刀锋长度84 x总长度117公厘，气泡套) PUMD-8.1 | PUMD-8.1 | 8.1mm | 84mm | 1piece | JPY: 2,330 | USD: 14.61 |
|
|
 |
61-1375-09 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.2 x刀锋长度84 x总长度117 mm,气泡套) PUMD-8.2 | PUMD-8.2 | 8.2mm | 84mm | 1piece | JPY: 2,280 | USD: 14.29 |
|
|
 |
61-1375-10 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.3 x刀锋长度84 x总长度117 mm,气泡套) PUMD-8.3 | PUMD-8.3 | 8.3mm | 84mm | 1piece | JPY: 2,330 | USD: 14.61 |
|
|
 |
61-1375-11 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.4 x刀锋长度87 x总长度121公厘，气泡套) PUMD-8.4 | PUMD-8.4 | 8.4mm | 87mm | 1piece | JPY: 2,380 | USD: 14.92 |
|
|
 |
61-1375-12 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.5 x刀锋长度87 x全长121 mm,吸塑包装) PUMD-8.5 | PUMD-8.5 | 8.5mm | 87mm | 1piece | JPY: 2,150 | USD: 13.48 |
|
|
 |
61-1375-13 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.6 x刀锋长度87 x全长121 mm,吸塑包装) PUMD-8.6 | PUMD-8.6 | 8.6mm | 87mm | 1piece | JPY: 2,580 | USD: 16.17 |
|
|
 |
61-1375-14 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.7 x刀锋长度87 x总长度121 mm,气泡套) PUMD-8.7 | PUMD-8.7 | 8.7mm | 87mm | 1piece | JPY: 2,580 | USD: 16.17 |
|
|
 |
61-1375-15 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.8 x刀锋长度89 x全长124 mm,吸塑包装) PUMD-8.8 | PUMD-8.8 | 8.8mm | 89mm | 1piece | JPY: 2,630 | USD: 16.49 |
|
|
 |
61-1375-16 | 小直径刀尖钻孔(Ultra MUSASHI,Φ8.9 x刀锋长度89 x总长度124 mm,气泡套) PUMD-8.9 | PUMD-8.9 | 8.9mm | 89mm | 1piece | JPY: 2,630 | USD: 16.49 |
|
|
 |
61-1375-17 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.0 x刀锋长度89 x总长度124 mm,气泡套) PUMD-9.0 | PUMD-9.0 | 9.0mm | 89mm | 1piece | JPY: 2,330 | USD: 14.61 |
|
|
 |
61-1375-18 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.1 x刀锋长度89 x总长度124公厘，气泡套) PUMD-9.1 | PUMD-9.1 | 9.1mm | 89mm | 1piece | JPY: 2,910 | USD: 18.24 |
|
|
 |
61-1375-19 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.2 x刀锋长度92 x总长度127 mm,气泡套) PUMD-9.2 | PUMD-9.2 | 9.2mm | 92mm | 1piece | JPY: 3,020 | USD: 18.93 |
|
|
 |
61-1375-20 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.3 x刀锋长度92 x总长度127 mm,气泡套) PUMD-9.3 | PUMD-9.3 | 9.3mm | 92mm | 1piece | JPY: 2,940 | USD: 18.43 |
|
|
 |
61-1375-21 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.4 x刀锋长度92 x全长127 mm,吸塑包装) PUMD-9.4 | PUMD-9.4 | 9.4mm | 92mm | 1piece | JPY: 3,020 | USD: 18.93 |
|
|
 |
61-1375-22 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.5 x刀锋长度92 x总长度127 mm,气泡套) PUMD-9.5 | PUMD-9.5 | 9.5mm | 92mm | 1piece | JPY: 2,710 | USD: 16.99 |
|
|
 |
61-1375-23 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.6 x刀锋长度95 x全长130 mm,薄膜包) PUMD-9.6 | PUMD-9.6 | 9.6mm | 95mm | 1piece | JPY: 3,210 | USD: 20.12 |
|
|
 |
61-1375-24 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.7 x刀锋长度95 x全长130 mm,吸塑包装) PUMD-9.7 | PUMD-9.7 | 9.7mm | 95mm | 1piece | JPY: 3,210 | USD: 20.12 |
|
|
 |
61-1375-25 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.8 x刀锋长度95 x全长130 mm,吸塑包装) PUMD-9.8 | PUMD-9.8 | 9.8mm | 95mm | 1piece | JPY: 3,210 | USD: 20.12 |
|
|
 |
61-1375-26 | 小直径刀尖钻孔(Ultra MUSASHI,Φ9.9 x刀锋长度95 x总长度130 mm,气泡套) PUMD-9.9 | PUMD-9.9 | 9.9mm | 95mm | 1piece | JPY: 3,470 | USD: 21.75 |
|
|
 |
61-1375-27 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.0 x刀锋长度95 x总长度130公厘，气泡套) PUMD-10.0 | PUMD-10.0 | 10.0mm | 95mm | 1piece | JPY: 2,940 | USD: 18.43 |
|
|
 |
61-1375-28 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.1 x刀锋长度98 x总长度133 mm,气泡套) PUMD-10.1 | PUMD-10.1 | 10.1mm | 98mm | 1piece | JPY: 3,930 | USD: 24.64 |
|
|
 |
61-1375-29 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.2 x刀锋长度98 x总长度133 mm,薄膜包) PUMD-10.2 | PUMD-10.2 | 10.2mm | 98mm | 1piece | JPY: 3,700 | USD: 23.19 |
|
|
 |
61-1375-30 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.3 x刀锋长度98 x总长度133公厘，气泡套) PUMD-10.3 | PUMD-10.3 | 10.3mm | 98mm | 1piece | JPY: 3,700 | USD: 23.19 |
|
|
 |
61-1375-31 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.4 x刀锋长度98 x总长度133 mm,气泡套) PUMD-10.4 | PUMD-10.4 | 10.4mm | 98mm | 1piece | JPY: 3,930 | USD: 24.64 |
|
|
 |
61-1375-32 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.5 x刀锋长度100 x总长度137公厘，气泡套) PUMD-10.5 | PUMD-10.5 | 10.5mm | 100mm | 1piece | JPY: 3,370 | USD: 21.13 |
|
|
 |
61-1375-33 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.6 x刀锋长度100 x总长度137公厘，气泡套) PUMD-10.6 | PUMD-10.6 | 10.6mm | 100mm | 1piece | JPY: 4,590 | USD: 28.77 |
|
|
 |
61-1375-34 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.7 x刀锋长度100 x总长度137公厘，气泡套) PUMD-10.7 | PUMD-10.7 | 10.7mm | 100mm | 1piece | JPY: 4,590 | USD: 28.77 |
|
|
 |
61-1375-35 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.8 x刀锋长度103 x总长度140公厘，气泡套) PUMD-10.8 | PUMD-10.8 | 10.8mm | 103mm | 1piece | JPY: 4,590 | USD: 28.77 |
|
|
 |
61-1375-36 | 小直径刀尖钻孔(Ultra MUSASHI,Φ10.9 x刀锋长度103 x总长度140公厘，气泡套) PUMD-10.9 | PUMD-10.9 | 10.9mm | 103mm | 1piece | JPY: 4,590 | USD: 28.77 |
|
|
 |
61-1375-37 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.0 x刀锋长度103 x总长度140 mm,气泡套) PUMD-11.0 | PUMD-11.0 | 11.0mm | 103mm | 1piece | JPY: 3,630 | USD: 22.75 |
|
|
 |
61-1375-38 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.1 x刀锋长度103 x总长度140公厘，气泡套) PUMD-11.1 | PUMD-11.1 | 11.1mm | 103mm | 1piece | JPY: 4,940 | USD: 30.97 |
|
|
 |
61-1375-39 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.2 x刀锋长度106 x全长143 mm,吸塑包装) PUMD-11.2 | PUMD-11.2 | 11.2mm | 106mm | 1piece | JPY: 4,750 | USD: 29.78 |
|
|
 |
61-1375-40 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.3 x刀锋长度106 x总长度143 mm,气泡套) PUMD-11.3 | PUMD-11.3 | 11.3mm | 106mm | 1piece | JPY: 4,940 | USD: 30.97 |
|
|
 |
61-1375-41 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.4 x刀锋长度106 x总长度143 mm,气泡套) PUMD-11.4 | PUMD-11.4 | 11.4mm | 106mm | 1piece | JPY: 4,750 | USD: 29.78 |
|
|
 |
61-1375-42 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.5 x刀锋长度106 x总长度143 mm,吸塑包装) PUMD-11.5 | PUMD-11.5 | 11.5mm | 106mm | 1piece | JPY: 4,200 | USD: 26.33 |
|
|
 |
61-1375-43 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.6 x刀锋长度109 x总长度146 mm,气泡套) PUMD-11.6 | PUMD-11.6 | 11.6mm | 109mm | 1piece | JPY: 5,100 | USD: 31.97 |
|
|
 |
61-1375-44 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.7 x刀锋长度109 x总长度146 mm,气泡套) PUMD-11.7 | PUMD-11.7 | 11.7mm | 109mm | 1piece | JPY: 5,300 | USD: 33.22 |
|
|
 |
61-1375-45 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.8 x刀锋长度109 x总长度146公厘，气泡套) PUMD-11.8 | PUMD-11.8 | 11.8mm | 109mm | 1piece | JPY: 5,100 | USD: 31.97 |
|
|
 |
61-1375-46 | 小直径刀尖钻孔(Ultra MUSASHI,Φ11.9 x刀锋长度109 x总长度146 mm,气泡套) PUMD-11.9 | PUMD-11.9 | 11.9mm | 109mm | 1piece | JPY: 5,300 | USD: 33.22 |
|
|
 |
61-1375-47 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.0 x刀锋长度111 x总长度149公厘，气泡套) PUMD-12.0 | PUMD-12.0 | 12.0mm | 111mm | 1piece | JPY: 4,420 | USD: 27.71 |
|
|
 |
61-1375-48 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.1 x刀锋长度111 x全长149 mm,泡罩包装) PUMD-12.1 | PUMD-12.1 | 12.1mm | 111mm | 1piece | JPY: 5,550 | USD: 34.79 |
|
|
 |
61-1375-49 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.2 x刀锋长度111 x总长度149 mm,气泡套) PUMD-12.2 | PUMD-12.2 | 12.2mm | 111mm | 1piece | JPY: 5,550 | USD: 34.79 |
|
|
 |
61-1375-50 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.3 x刀锋长度111 x总长度149 mm,吸塑包装) PUMD-12.3 | PUMD-12.3 | 12.3mm | 111mm | 1piece | JPY: 5,550 | USD: 34.79 |
|
|
 |
61-1375-51 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.4 x刀锋长度114 x总长度152 mm,吸塑包装) PUMD-12.4 | PUMD-12.4 | 12.4mm | 114mm | 1piece | JPY: 5,780 | USD: 36.23 |
|
|
 |
61-1375-52 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.5 x刀锋长度114 x总长度152 mm,气泡套) PUMD-12.5 | PUMD-12.5 | 12.5mm | 114mm | 1piece | JPY: 4,900 | USD: 30.72 |
|
|
 |
61-1375-53 | 小直径刀尖钻孔(UltraMUSASHI,Φ12.6 x刀锋长度114 x全长152 mm,吸塑包装) PUMD-12.6 | PUMD-12.6 | 12.6mm | 114mm | 1piece | JPY: 6,110 | USD: 38.30 |
|
|
 |
61-1375-54 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.7 x刀锋长度114 x总长度152 mm,吸塑包装) PUMD-12.7 | PUMD-12.7 | 12.7mm | 114mm | 1piece | JPY: 5,880 | USD: 36.86 |
|
|
 |
61-1375-55 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.8 x刀锋长度114 x全长152 mm,吸塑包装) PUMD-12.8 | PUMD-12.8 | 12.8mm | 114mm | 1piece | JPY: 6,110 | USD: 38.30 |
|
|
 |
61-1375-56 | 小直径刀尖钻孔(Ultra MUSASHI,Φ12.9 x刀锋长度114 x总长度152 mm,薄膜包) PUMD-12.9 | PUMD-12.9 | 12.9mm | 114mm | 1piece | JPY: 6,110 | USD: 38.30 |
|
|
 |
61-1375-57 | 小直径刀尖钻孔(Ultra MUSASHI,Φ13.0 x刀锋长度114 x总长度152 mm,吸塑包装) PUMD-13.0 | PUMD-13.0 | 13.0mm | 114mm | 1piece | JPY: 5,050 | USD: 31.66 |
|