Pipe Bender
Filters
-
Medibendar and others
2 products found
JPY: 987,500-
USD: 6,194.33-
-
Rebar vendors and others
3 products found
JPY: 260,000-
USD: 1,630.91-
-
Bender for small diameter pipe 66200
It is easy to perform bending of difficult small diameter pipes.
1 products found
JPY: 2,560
USD: 16.06
-
-
Hand bender HB16W
Can bend freely from 0 to 135 degrees without any steps.
Up to 3 pieces of D10 rebar and 2 pieces of D13 rebar can be bent simultaneously.1 products found
JPY: 259,730
USD: 1,629.22
-
Electric-Hydraulic pumps discharge amount (high pressure) 0.35 L/min (low pressure) 2.5 L/min and others
2 products found
JPY: 360,000-
USD: 2,258.19-
-
Manual pumps SP-2
Lightweight design using aluminum alloy.
Comes with a handle that is easy to hold.1 products found
JPY: 101,200
USD: 634.80
-
-
-
-
-
Heavy-Duty Bender DBD25H
Supports rebar up to SD490/D25.
Professional specification that can be used even in harsh environments.1 products found
JPY: 528,130
USD: 3,312.82
-
Handy Bender Cutter DBC16H
Rebar up to SD390/D16 can be machined.
Maximum bend angle of 180 degrees, combination of vendor and cutter.1 products found
JPY: 315,000
USD: 1,975.91
-
Heavy-Duty Bender Cutter DBC25X
Stationary vendor cutter capable of cutting and bending rebar up to 25 mm.
Bending and cutting can be switched with a single switch.1 products found
JPY: 831,250
USD: 5,214.21
-
-
Rebar Bender DBS13
It is possible to process the thread instantly.
Reduces the load on the lower back of the worker. Quick continuous work is possible just by pressing the switch.1 products found
JPY: 227,500
USD: 1,427.05
-
Rebar Bender DBS16H
Can bend 65 mm from the wall.
SD490 rebar can be supported by using optional parts.1 products found
JPY: 349,450
USD: 2,192.01
-
-
Pipe Bender SPB1025N
Bending (0~90°) of thick (JIS standard) stainless steel pipes, gas pipes (JIS), water pipes and electric pipes.
Comes with 3 types of attachments (bend shoes) according to bending.1 products found
JPY: 151,570
USD: 950.76
-
Bend Shoe L (mm): 106 H (mm): 57 W (mm): 28 Bend Radius (mm): R50 Mass (kg): 0.65 and others
4 products found
JPY: 12,250-
USD: 76.84-
-
-
[Discontinued]Hydraulic gas pipe vendors NC-PB-G1-HP
A vendor dedicated to bending gas pipes.
Compact open/close frame for beautiful and precise bending without damaging pipes.1 products found
JPY: 212,125
USD: 1,330.61
-
[Discontinued]Manual hydraulic vendors and others
7 products found
JPY: 178,000-
USD: 1,116.55-
-
[Discontinued]Cordless vendors HBB-90DFN
This is a charging point bar vendor for D16 that is easy to bend in the field.
Fully charged, D16 rebar can be bent continuously 50 times.1 products found
JPY: 230,625
USD: 1,446.65
-
[Discontinued]Portable rebar vendor MB816
It can isolate the working part and the structural part and block iron powder.
The discharge port of the back panel is improved, and a lot of iron powder can be released.1 products found
JPY: 262,500
USD: 1,646.59
-
[Discontinued]SK 11 Pipe Bender Set 3PCS
Can be easily bent to any angle.
Bending of soft copper pipes, aluminum pipes, etc.1 products found
JPY: 840
USD: 5.27
