Ogura & Co., Ltd.

Electric hydraulic Reinforced Cutter and others

Ogura & Co., Ltd.

Electric hydraulic multipurpose, Stool Body and others

Ogura & Co., Ltd.

Battery 3. 0Ah　BL1830B

Since there is no memory effect, you can use it when you want to use it and charge it when you want to charge it.
You can easily and reliably get a full charge.

Ogura & Co., Ltd.

Battery 6. 0Ah　BL1860B

Since there is no memory effect, you can use it when you want to use it and charge it when you want to charge it.
You can easily and reliably get a full charge.

Ogura & Co., Ltd.

Portable Bar Bendor MB225　MB-225

Fully compatible with SD490 rebar.
The bend angle setting is a dial type, and it is optional non-step setting by using the fine adjustment lever together.

Ogura & Co., Ltd.

Portable Bar Bendor MB819　MB-819

Fully compatible with SD490 rebar.
The bend angle setting is a dial type, and it is optional non-step setting by using the fine adjustment lever together.

Ogura & Co., Ltd.

Rapid Charger　DC18RF

New and optimal charging control reduces charging time.

Ogura & Co., Ltd.

［Discontinued］Charger and others

Ogura & Co., Ltd.

［Discontinued］Cordless hydraulic Puncher　HPC-N209WDF

Cordless puncher for mild steel up to t9.
The hole diameter φ20/plate thickness t9mm (SS400 material) can be drilled continuously 40 times.

Ogura & Co., Ltd.

［Discontinued］Cordless Cutter and others

Ogura & Co., Ltd.

［Discontinued］Cordless vendors　HBB-90DFN

This is a charging point bar vendor for D16 that is easy to bend in the field.
Fully charged, D16 rebar can be bent continuously 50 times.

Ogura & Co., Ltd.

［Discontinued］Portable rebar vendor　MB816

It can isolate the working part and the structural part and block iron powder.
The discharge port of the back panel is improved, and a lot of iron powder can be released.

Ogura & Co., Ltd.

［Discontinued］Cordless Reinforced Cutter　HCC-13DF

The cutting speed is about twice as high as that of conventional machines, and the work efficiency is about twice as high.
The D13 (SD345) can be disconnected approximately 240 times on a single charge.

Ogura & Co., Ltd.

［Discontinued］Cordless hydraulic Puncher　HPC-156WDF

A lightweight and compact double acting puncher for drilling φ15 mm stainless steel t6mm.
Both punching and pulling are hydraulically actuated by the double action type, which eliminates the snagging on the members during pulling up, allowing you to work in the field without stress.

Ogura & Co., Ltd.

［Discontinued］Hydraulic Puncher　HPCNF188W

A neck break puncher that can be drilled at any position from 0° to 90°.
Simple double motion system allows you to pull up without worry.

Ogura & Co., Ltd.

［Discontinued］Rechargeable zlahti Cutter　HSC20BL60AH

Even though it is a cordless type, it has the high power of an AC100V machine.
It is possible to cut the opening of the reinforcing bar and the frame bar at 3.5 mm from the collar and the edge.

Ogura & Co., Ltd.

［Discontinued］Zlahti Cutter　HSC25BL

Even though it is cordless, it has the high power of an AC100V machine.
It is possible to cut the opening of the reinforcing bar and the frame bar at 3.5 mm from the collar and the edge.

Ogura & Co., Ltd.

［Discontinued］HSC 25 BL for Chip Saw　OCD25110

Ogura & Co., Ltd.

［Discontinued］Cordless Heavy Duty Cutter　HCC-16BL

The fastest DC18V cordless cutter ever, D16 (SD345) rebar can be cut in about 2.6 seconds.
It is equipped with a new brushless motor that achieves overwhelmingly high power.

Ogura & Co., Ltd.

［Discontinued］Cordless Bar Cutter　HSC-20BLN

The new original chip saw, which has excellent cost performance, uses a strong irregular triple pin system, and achieves stable cutting performance and easy operation even without flanges.
Even though it is a cordless type, it has the high power of an AC100V machine.