[United Automation] AllProducts
Lab Instruments & Supplies
-
Electronic/Electrical Parts and Controll Equipments
-
Fan Speed Controller, Infinitely Variable, 110 V ac, 15A A72162
VAC2-15E 15A Fan Speed Controller. These variable phase angle regulators are robust, compact and enclosed units for 230V or 110V up to 15A single phase mains driven inductive loads, such as induction motors, fans ; pumps. They give fully adjustable voltage outputs from zero to maximum. A version (/S) of these controllers also incorporate an OFF switch when the potentiometer is fully anti-clockwise. The controller has an integral RC Snubber network for control of inductive loads. Minimum Set Speed adjuster (at the rear) allows the designer/installer to fix a minimum output voltage level to prevent a motor being driven too slow. Infinitely variable 0-98% output Optional OFF switch on potentiometer (/S versions) Minimum Set Speed Adjuster Single hole fixing Rugged and compact Large triac for inrush protection Integral RC Snubber Suitable applications for most single-phase mains voltage driven Motors ; Fans
1 products found
JPY: 18,200
USD: 113.24
-
United Automation, PATFC, Firing Circuit Commander Module, 11 x 4 x 9mm PATFC
Phase Angle Triac Firing Circuit - United Automation. Thick film hybrid firing circuit Gives phase control of most loads in the range 1 to 100 amps (depending on choice of triac, heat sink and potentiometer)
1 products found
JPY: 7,750
USD: 48.22
-
United Automation, 230 V Voltage Regulator, 10A, 1-Channel, Adjustable 3-Pin CSR1004B CSR1004B
CSR Power Regulator 6A, 10A & 15A, United Automation. United Automation CSR Power Regulator integrated chips (IC) control single phase mains driven loads of 6A, 10A and 15A. The Solid-state phase controlled power regulator needs external 220 k or 250 k linear potentiometers (not supplied) and controls the power into a resistive load from 0% to 98%. Applications include resistive heating elements like quartz lamps, ovens and dryers as well as some inductive loads such as transformers, fans and motors.. Transistor style housing with isolated heat sink tab
1 products found
JPY: 9,040
USD: 56.25
-
United Automation, 230 V Voltage Regulator, 15A, 1-Channel, Adjustable 3-Pin CSR1504B CSR1504B
CSR Power Regulator 6A, 10A & 15A, United Automation. United Automation CSR Power Regulator integrated chips (IC) control single phase mains driven loads of 6A, 10A and 15A. The Solid-state phase controlled power regulator needs external 220 k or 250 k linear potentiometers (not supplied) and controls the power into a resistive load from 0% to 98%. Applications include resistive heating elements like quartz lamps, ovens and dryers as well as some inductive loads such as transformers, fans and motors.. Transistor style housing with isolated heat sink tab
1 products found
JPY: 9,040
USD: 56.25
-
United Automation PIR Sensor A86616
Infresco PIR Movement Sensor
This 12V single-head Passive Infra-Red (PIR) sensor is intended to work with the Infresco VR range1 products found
JPY: 28,400
USD: 176.71
-
Temperature Sensor -50 → +110°C, United Automation A86614, Interior Room, Thermistor A86614
Infresco 10K NTC Thermistor Sensor. Temperature range: -50 → +100°C (110°C max) 0.5 meter lead Fully encapsulated sensor, offering IP68 water protection Absolute integrity against moisture ingress Dielectric strength: 4kVac Suitable for refrigeration, air conditioning, solar and underfloor heating
1 products found
JPY: 2,460
USD: 15.31
-
Fan Speed Controller, Infinitely Variable, 230 V ac, 15A VAC2/-15E
VAC2-15E 15A Fan Speed Controller. These variable phase angle regulators are robust, compact and enclosed units for 230V or 110V up to 15A single phase mains driven inductive loads, such as induction motors, fans ; pumps. They give fully adjustable voltage outputs from zero to maximum. A version (/S) of these controllers also incorporate an OFF switch when the potentiometer is fully anti-clockwise. The controller has an integral RC Snubber network for control of inductive loads. Minimum Set Speed adjuster (at the rear) allows the designer/installer to fix a minimum output voltage level to prevent a motor being driven too slow. Infinitely variable 0-98% output Optional OFF switch on potentiometer (/S versions) Minimum Set Speed Adjuster Single hole fixing Rugged and compact Large triac for inrush protection Integral RC Snubber Suitable applications for most single-phase mains voltage driven Motors ; Fans
1 products found
JPY: 18,900
USD: 117.60
-
Fan Speed Controller, Infinitely Variable, 110 V ac, 15A A72152
VAC2-15E 15A Fan Speed Controller. These variable phase angle regulators are robust, compact and enclosed units for 230V or 110V up to 15A single phase mains driven inductive loads, such as induction motors, fans ; pumps. They give fully adjustable voltage outputs from zero to maximum. A version (/S) of these controllers also incorporate an OFF switch when the potentiometer is fully anti-clockwise. The controller has an integral RC Snubber network for control of inductive loads. Minimum Set Speed adjuster (at the rear) allows the designer/installer to fix a minimum output voltage level to prevent a motor being driven too slow. Infinitely variable 0-98% output Optional OFF switch on potentiometer (/S versions) Minimum Set Speed Adjuster Single hole fixing Rugged and compact Large triac for inrush protection Integral RC Snubber Suitable applications for most single-phase mains voltage driven Motors ; Fans
1 products found
JPY: 18,300
USD: 113.86
-
Fan Speed Controller, Infinitely Variable, 230 V ac, 15A VAC2/S-15E
VAC2-15E 15A Fan Speed Controller. These variable phase angle regulators are robust, compact and enclosed units for 230V or 110V up to 15A single phase mains driven inductive loads, such as induction motors, fans ; pumps. They give fully adjustable voltage outputs from zero to maximum. A version (/S) of these controllers also incorporate an OFF switch when the potentiometer is fully anti-clockwise. The controller has an integral RC Snubber network for control of inductive loads. Minimum Set Speed adjuster (at the rear) allows the designer/installer to fix a minimum output voltage level to prevent a motor being driven too slow. Infinitely variable 0-98% output Optional OFF switch on potentiometer (/S versions) Minimum Set Speed Adjuster Single hole fixing Rugged and compact Large triac for inrush protection Integral RC Snubber Suitable applications for most single-phase mains voltage driven Motors ; Fans
1 products found
JPY: 19,200
USD: 119.46
-
United Automation, 230 V Voltage Regulator, 6A, 1-Channel, Adjustable 3-Pin CSR604B CSR604B
CSR Power Regulator 6A, 10A & 15A, United Automation. United Automation CSR Power Regulator integrated chips (IC) control single phase mains driven loads of 6A, 10A and 15A. The Solid-state phase controlled power regulator needs external 220 k or 250 k linear potentiometers (not supplied) and controls the power into a resistive load from 0% to 98%. Applications include resistive heating elements like quartz lamps, ovens and dryers as well as some inductive loads such as transformers, fans and motors.. Transistor style housing with isolated heat sink tab
1 products found
JPY: 9,070
USD: 56.43
-
Fan Speed Controller, Infinitely Variable, 230 V ac, 3A VAC2-3/RFI
VAC2-3/RFI 3A Fan Speed Controller + RFI Filter. The VAC2-3/RFI is a compact variable phase-angle regulator of open construction and suitable for 230V single-phase operation with mains driven inductive loads, such as induction motors, fans and pumps. An integral choke/capacitor RFI circuit enables the controller to meet current EMC standards for emissions. Infinitely variable 0-98% output Maximum RMS on-state current: 3A Minimum operating current: 100mA Minimum Set Speed Adjuster Large triac for inrush protection Integral RC Snubber Integral EMC filtering Peak one cycle surge @ 10mS: 150A I²t for fusing: 100A²s Isolation voltage: 2500 Vrms Maximum recommended unit temperature: +70ºC Mains supply: 230 Vac ±10% @ 50/60Hz Single hole fixing
1 products found
JPY: 14,300
USD: 88.98
-
United Automation, PR3-E-6kW, HVAC Control, 6kW, 8A, 770g, 105 x 193 x 68mm PR3-E-6kW
Single-phase units do not include failsafe alarms. PRx-E series 1 & 3-Phase HVAC Controllers. The PRx-E thyristor stack units provide full seamless control of 1/3-phase resistive loads. Burst-firing control stack uses fast pulse zero-voltage switching technology to minimise flicker and RFI problems Integral fusing, temperature trip, automatic reset and heatsink Housed in bespoke enclosures with easy access to internal signal and power terminals to minimise installation time Applications: Heater batteries, Air curtains, Ovens, Furnaces, Hotplates, Dryers, HVAC RS Product Codes < 489-3547') 489-3547/ PR1-E-3KW Single-phase 3kW < 489-3553') 489-3553/ PR1-E-6KW Single-phase 6kW < 919-6245') 919-6245/ PR3-E-6KW Three-phase 6kW < 489-3569') 489-3569/ PR3-E-12KW Three-phase 12kW < 489-3575') 489-3575/ PR3-E-18KW Three-phase 18kW
1 products found
JPY: 72,700
USD: 452.34
-
Fan Speed Controller, Infinitely Variable, 230 V ac, 1A VAC2-1/RFI
VAC2-1/RFI 1A Fan Speed Controller + RFI Filter. The VAC2-1/RFI is a compact variable phase-angle regulator of open construction and suitable for 230V single-phase operation with mains driven inductive loads, such as induction motors, fans and pumps. An integral choke/capacitor RFI circuit enables the controller to meet current EMC standards for emissions. Infinitely variable 0-98% output Maximum RMS on-state current: 1A Minimum operating current: 100mA Minimum Set Speed Adjuster Large triac for inrush protection Integral RC Snubber Integral EMC filtering Peak one cycle surge @ 10mS: 80A I²t for fusing: 36A²s Isolation voltage: 2500 Vrms Maximum recommended unit temperature: +70ºC Mains supply: 230 Vac ±10% @ 50/60Hz Single hole fixing
1 products found
JPY: 11,200
USD: 69.69
-
［Discontinued］United Automation, ZAX27A, Thyristor Power Controller ZAX27A
Phase Angle & Burst Firing Control Module - United Automation. Fully isolated device features an integral power circuit capable of controlling currents up to 1·5A. Suitable for slave firing triacs or thyristor pairs Phase-angle or Burst firing operating modes (hot selectable by 1 pin logic change) Output inhibit, overheat shut down, soft-start and current limit Accurate regulation of power to all loads Capable of microcontroller control Uncommitted op-amp can be used as an error amplifier or comparator for feedback
1 products found
JPY: 8,500
USD: 52.89
-
［Out of stock］Fan Speed Controller, 230 V ac, 10A FPSC230/10
10A Fan and Pump Speed Controller, FSC230/10. The FSC230/10 Variable Fan Speed Controller is designed for mains 230Vac, 10A single-phase driven inductive loads, giving fully adjustable voltage outputs from zero to maximum. This allows to set a minimum output voltage level in order to prevent a motor from being driven to slowly. Standard Din Rail mount Phase angle control Integral Protection Built-in snubber network Input signal or Potentiometer (0-5/0-10VDC 4-20mA) Output power span and zero (Minimum Speed Set) Power and status LEDs Up to 10A Load Built-in Heatsink
1 products found
JPY: 31,100
USD: 193.50
-
［Out of stock］United Automation, DMFC36, Thyristor Trigger Module, 24V ac, 9-Pin, 160 x 62 x 62mm DMFC36
Multi Mode, Phase-Angle & Single/Dual Cycle Burst Firing Circuit, DMFC-36. The DMFC-36 module has been designed to offer Phase-Angle or Burst Fire Control in firing a thyristor assembly or complete thyristor controller for driving resistive loads. In Single-Cycle or Dual-Cycle mode, these modules use the fastest burst rates possible, providing very accurate control and minimising Harmonic distortion & Flicker within the system. Includes a Transformer Standard Din Rail Mount On Board Indication of Power, Burst-Rates & Fault Conditions Phase-Angle, or Burst Fire Control Single-Cycle / Dual Cycle Burst Fire modes of control or adjustable Standard Burst Firing Soft-start (1 to 30 seconds) Inhibit Input Wide Range of Control Options: 0-5V, 0-10V, 1-5V, 2-10V, 0-20mA, 4-20mA, Manual Potentiometer Isolated Pulse transformer outputs On Board Protection Fuse
1 products found
JPY: 88,600
USD: 551.27
-
［Discontinued］United Automation, PFC2 30KVR , Power Factor Switch, 50A, 3kg, 205 x 155 x 120mm PFC2 30KVR
Metal parts, in particular the case may get very hot when the unit is fully operational. PFC2 30/50kVAR Power Factor Switches. The PFC2 controllers are suitable for 3-wire, 3-phase floating-star or closed-delta configured capacitive loads for Power Factor Correction and can be used in capacitor banks with or without chokes fitted. They are designed to dramatically reduce the inrush current normally found with contactor-based systems and could be used in situations where rapid changes in Power Factor occur such as welding plants, lifts, cranes and wind-powered plants. Current rating: 50A ( 30kVAR ), 75A ( 50kVAR ) @ 415Vrms Input voltage: 415Vrms ±10% Frequency: 50/60Hz Control signal input: +8 to +24Vdc, Common 0V or Common +VE, Open Collector or Volt Free Contact Alarm relay functions: Voltage free alarm relay is rated for 125Vac @ 2A. LED indicators: Green : DC Power ON, Red : Fault, Orange : Signal enabled, Red/Orange : Capacitors discharging Cooling fan: +24Vdc ( 50KVAR model only ) Fan switch-on : 50KVAR units typically +55ºC Over Temperature: Trip in temperature: +90ºC ±1ºC (Status LED indicator flashes with ON/OFF rapid pulsing Trip out temperature: +85ºC ±1ºC Phase loss detection: Phase loss or Fuse failure orange and red LEDs flash alternately Status LED Fault condition: Status LED indicator flashes ON/OFF continuously at 1.5 second intervals Sensor loss detection: Status LED indicator flashes ON/OFF continuously in equal intervals Power cable terminations: Supply and Load16mm² rising clamp terminal block Earth16mm² rising clamp terminal block Terminal torque settings: 2.5Nm (16mm²) Power terminals only Signal cable terminations: Remote supply Auxiliary alarm (relay) 2.5mm² rising clamp terminal block Control signal 2.5mm² rising clamp terminal block Environmental Protection: IP20 Fusing 30kVAR: 63ET (63A) High-Speed Semiconductor type fuse, or equivalent Fusing 50kVAR: 100ET (100A) High-Speed Semiconductor type fuse, or equivalent Working temperature: +65°C (maximum operational) Dimensions: 205 x 155 x 120mm Fixing centres: 4 x 4.5mm-clear keyhole slots on fixing centres 140 x 140mm Weight: ( 30kVAR ) 3.0kg ( 50kVAR ) 3.4kg RS Product Codes < 919-6220') 919-6220/ PFC2 30kVAR < 919-6239') 919-6239/ PFC2 50kVAR
1 products found
JPY: 55,700
USD: 346.57
-
［Discontinued］United Automation, PFC2 80KVR, Power Factor Switch, 125A, 5.6kg, 270 x 250 x 130mm PFC2 80KVR
Metal parts, in particular the case may get very hot when the unit is fully operational. PFC2 80/100kVAR Power Factor Switches. The PFC2 controllers are suitable for 3-wire, 3-phase floating-star or closed-delta configured capacitive loads for Power Factor Correction and can be used in capacitor banks with or without chokes fitted. They are designed to dramatically reduce the inrush current normally found with contactor-based systems and could be used in situations where rapid changes in Power Factor occur such as welding plants, lifts, cranes and wind-powered plants. Current rating: 125A ( 80kVAR ), 150A ( 100kVAR ) @ 415Vrms Input voltage: 415Vrms ±10% Frequency: 50/60Hz Control signal input: +8 to +24Vdc, Common 0V or Common +VE, Open Collector or Volt Free Contact Alarm relay functions: Voltage free alarm relay is rated for 125Vac @ 2A. LED indicators: Green : DC Power ON, Red : Fault, Orange : Signal enabled, Red/Orange : Capacitors discharging Cooling fan: +24Vdc Fan switch-on : Typically +55ºC Over Temperature: Trip in temperature: +90ºC ±1ºC (Status LED indicator flashes with ON/OFF rapid pulsing Trip out temperature: +85ºC ±1ºC Phase loss detection: Phase loss or Fuse failure orange and red LEDs flash alternately Status LED Fault condition: Status LED indicator flashes ON/OFF continuously at 1.5 second intervals Sensor loss detection: Status LED indicator flashes ON/OFF continuously in equal intervals Power cable terminations: Supply, Load & Earth 35mm² rising clamp terminal block Terminal torque settings: 3.2Nm min (35mm²) Power terminals only Signal cable terminations: Remote supply Auxiliary alarm (relay) 2.5mm² rising clamp terminal block Control signal 2.5mm² rising clamp terminal block Environmental Protection: IP20 Fusing 80kVAR: 160EET (160A) High-Speed Semiconductor type fuse, or equivalent Fusing 100kVAR: 200EET (200A) High-Speed Semiconductor type fuse, or equivalent Working temperature: +65°C (maximum operational) Dimensions: 270 x 250 x 130mm Fixing centres: 4 x 4.5mm-clear keyhole slots on fixing centres 227 x 200mm Weight: 5.6kg RS Product Codes < 919-6232') 919-6232/ PFC2 80kVAR < 919-6236') 919-6236/ PFC2 100kVAR
1 products found
JPY: 107,000
USD: 665.75
-
［Discontinued］United Automation, PFC2 100KVR, Power Factor Switch, 150A, 5.6kg, 270 x 250 x 130mm PFC2 100KVR
Metal parts, in particular the case may get very hot when the unit is fully operational. PFC2 80/100kVAR Power Factor Switches. The PFC2 controllers are suitable for 3-wire, 3-phase floating-star or closed-delta configured capacitive loads for Power Factor Correction and can be used in capacitor banks with or without chokes fitted. They are designed to dramatically reduce the inrush current normally found with contactor-based systems and could be used in situations where rapid changes in Power Factor occur such as welding plants, lifts, cranes and wind-powered plants. Current rating: 125A ( 80kVAR ), 150A ( 100kVAR ) @ 415Vrms Input voltage: 415Vrms ±10% Frequency: 50/60Hz Control signal input: +8 to +24Vdc, Common 0V or Common +VE, Open Collector or Volt Free Contact Alarm relay functions: Voltage free alarm relay is rated for 125Vac @ 2A. LED indicators: Green : DC Power ON, Red : Fault, Orange : Signal enabled, Red/Orange : Capacitors discharging Cooling fan: +24Vdc Fan switch-on : Typically +55ºC Over Temperature: Trip in temperature: +90ºC ±1ºC (Status LED indicator flashes with ON/OFF rapid pulsing Trip out temperature: +85ºC ±1ºC Phase loss detection: Phase loss or Fuse failure orange and red LEDs flash alternately Status LED Fault condition: Status LED indicator flashes ON/OFF continuously at 1.5 second intervals Sensor loss detection: Status LED indicator flashes ON/OFF continuously in equal intervals Power cable terminations: Supply, Load & Earth 35mm² rising clamp terminal block Terminal torque settings: 3.2Nm min (35mm²) Power terminals only Signal cable terminations: Remote supply Auxiliary alarm (relay) 2.5mm² rising clamp terminal block Control signal 2.5mm² rising clamp terminal block Environmental Protection: IP20 Fusing 80kVAR: 160EET (160A) High-Speed Semiconductor type fuse, or equivalent Fusing 100kVAR: 200EET (200A) High-Speed Semiconductor type fuse, or equivalent Working temperature: +65°C (maximum operational) Dimensions: 270 x 250 x 130mm Fixing centres: 4 x 4.5mm-clear keyhole slots on fixing centres 227 x 200mm Weight: 5.6kg RS Product Codes < 919-6232') 919-6232/ PFC2 80kVAR < 919-6236') 919-6236/ PFC2 100kVAR
1 products found
JPY: 98,000
USD: 609.76
