[Cooper Bussmann]Fuses
Filters
- by Product group
- by Product
Sort by:
-
Cooper Bussmann, 750mA Glass Cartridge Fuse, 6.3 x 32mm, Speed T TDC11-750MA
All fuses 6.3mm (0.25in) diameter and 32mm (1.25in) in length. Glass Body - (T) LBC. Glass tube fuses are available in with fast acting and time delay characteristics which makes them suitable for a variety of different applications. Glass cartridge fuses are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass cartridge 6.3mm x 21 mm cartridge size T Speed Rating Low Breaking Capacity Typical applications: Cartridge fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances such as motors air-conditions, refrigerator, pumps etc. They can be found in the following areas: Industrial Commercial Home/Residential Automotive Additional Information: What size is it? 6.3 x 32mm is a miniature cartridge size. Miniature fuses are ideal for the protection of electrical appliances, electronic equipment and component parts. Why choose a glass fuse? Glass and ceramic fuses have similar properties. However you may choose a glass fuse as it enables you to see the inside of the fuse. Therefore it is easier to determine whether the fuse has blown. What are fuses used for? For the protection of components and equipment from costly damage caused by over-current. To isolate sub-systems from the main system once a fault has appeared What is an over-current? It is a setting where a circuit experiences a current that is higher than the normal operating current. What Speed is it? This particular fuse is T speed rated which means it is a slow acting fuse, sometimes referred to as anti-surge. It is able to tolerate higher levels for a short period, without shorting. Therefore, if a sudden change occurs, this fuse will not blow immediately. They are suitable for applications where a sudden flow of high current is required. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity).
1 products found
JPY: 313,000
USD: 1,962.01
-
Cooper Bussmann, 250mA Glass Cartridge Fuse, 6.3 x 32mm, Speed F TDC10-250MA
Quick Acting (F) LBC Glass Cartridge Fuse. This glass cartridge fuse is ideal for providing protection to devices or internal circuits. They are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass tube, electroplated brass endcap construction 6.3 x 32 mm cartridge size F Speed Rating RoHS compliant and lead-free Interrupting rating equals 10 times rated current Typical applications: Miniature fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances, electronic equipment and component parts More information: Why choose a glass fuse? Glass and ceramic fuses have similar properties. Glass fuse is great for small items that don't draw a heavy amount of current and blow on a regular basis. It is easy to identify whether the fuse has blown as you can see inside it. What size is it? 6.3 x 32 mm is a standard cartridge size and it measures approximately 32 mm long by 6.3 mm in diameter. They are popular in board and panel protection and will fit a compatible 6.3 x 32 fuse holder. What Speed is it? This particular fuse is ''F'' speed rated which means a fast acting fuse. These are designed to protect less sensitive components and are also used to protect cabling from melting or catching fire when an overload appear. Every fast acting fuse will have the exact speed stated which will be relevant to different overloads. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity). What are fuses used for? For the protection of components and equipment from costly damage caused by over-current To isolate sub-systems from the main system once a fault has appeared What is an overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 125,000
USD: 783.55
-
Cooper Bussmann, 500mA Glass Cartridge Fuse, 6.3 x 32mm, Speed F TDC10-500-R
Quick Acting (F) LBC Glass Cartridge Fuse. This glass cartridge fuse is ideal for providing protection to devices or internal circuits. They are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass tube, electroplated brass endcap construction 6.3 x 32 mm cartridge size F Speed Rating RoHS compliant and lead-free Interrupting rating equals 10 times rated current Typical applications: Miniature fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances, electronic equipment and component parts More information: Why choose a glass fuse? Glass and ceramic fuses have similar properties. Glass fuse is great for small items that don't draw a heavy amount of current and blow on a regular basis. It is easy to identify whether the fuse has blown as you can see inside it. What size is it? 6.3 x 32 mm is a standard cartridge size and it measures approximately 32 mm long by 6.3 mm in diameter. They are popular in board and panel protection and will fit a compatible 6.3 x 32 fuse holder. What Speed is it? This particular fuse is ''F'' speed rated which means a fast acting fuse. These are designed to protect less sensitive components and are also used to protect cabling from melting or catching fire when an overload appear. Every fast acting fuse will have the exact speed stated which will be relevant to different overloads. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity). What are fuses used for? For the protection of components and equipment from costly damage caused by over-current To isolate sub-systems from the main system once a fault has appeared What is an overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 228,000
USD: 1,429.20
-
Cooper Bussmann, 150mA Glass Cartridge Fuse, 6.3 x 32mm, Speed T TDC11-150MA
All fuses 6.3mm (0.25in) diameter and 32mm (1.25in) in length. Glass Body - (T) LBC. Glass tube fuses are available in with fast acting and time delay characteristics which makes them suitable for a variety of different applications. Glass cartridge fuses are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass cartridge 6.3mm x 21 mm cartridge size T Speed Rating Low Breaking Capacity Typical applications: Cartridge fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances such as motors air-conditions, refrigerator, pumps etc. They can be found in the following areas: Industrial Commercial Home/Residential Automotive Additional Information: What size is it? 6.3 x 32mm is a miniature cartridge size. Miniature fuses are ideal for the protection of electrical appliances, electronic equipment and component parts. Why choose a glass fuse? Glass and ceramic fuses have similar properties. However you may choose a glass fuse as it enables you to see the inside of the fuse. Therefore it is easier to determine whether the fuse has blown. What are fuses used for? For the protection of components and equipment from costly damage caused by over-current. To isolate sub-systems from the main system once a fault has appeared What is an over-current? It is a setting where a circuit experiences a current that is higher than the normal operating current. What Speed is it? This particular fuse is T speed rated which means it is a slow acting fuse, sometimes referred to as anti-surge. It is able to tolerate higher levels for a short period, without shorting. Therefore, if a sudden change occurs, this fuse will not blow immediately. They are suitable for applications where a sudden flow of high current is required. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity).
1 products found
JPY: 517,000
USD: 3,240.77
-
Cooper Bussmann, 250mA Glass Cartridge Fuse, 6.3 x 32mm, Speed T TDC11-250MA
All fuses 6.3mm (0.25in) diameter and 32mm (1.25in) in length. Glass Body - (T) LBC. Glass tube fuses are available in with fast acting and time delay characteristics which makes them suitable for a variety of different applications. Glass cartridge fuses are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass cartridge 6.3mm x 21 mm cartridge size T Speed Rating Low Breaking Capacity Typical applications: Cartridge fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances such as motors air-conditions, refrigerator, pumps etc. They can be found in the following areas: Industrial Commercial Home/Residential Automotive Additional Information: What size is it? 6.3 x 32mm is a miniature cartridge size. Miniature fuses are ideal for the protection of electrical appliances, electronic equipment and component parts. Why choose a glass fuse? Glass and ceramic fuses have similar properties. However you may choose a glass fuse as it enables you to see the inside of the fuse. Therefore it is easier to determine whether the fuse has blown. What are fuses used for? For the protection of components and equipment from costly damage caused by over-current. To isolate sub-systems from the main system once a fault has appeared What is an over-current? It is a setting where a circuit experiences a current that is higher than the normal operating current. What Speed is it? This particular fuse is T speed rated which means it is a slow acting fuse, sometimes referred to as anti-surge. It is able to tolerate higher levels for a short period, without shorting. Therefore, if a sudden change occurs, this fuse will not blow immediately. They are suitable for applications where a sudden flow of high current is required. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity).
1 products found
JPY: 714,000
USD: 4,475.65
-
Cooper Bussmann, 32A, A2, British Standard Fuse, gG - gM, 550V ac AAO32M40
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,580
USD: 22.44
-
Cooper Bussmann, 32A, A2, British Standard Fuse, gG - gM, 550V ac AAO32M50
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,580
USD: 22.44
-
Cooper Bussmann, 32A, A2, British Standard Fuse, gG - gM, 550V ac AAO32M63
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,980
USD: 24.95
-
Cooper Bussmann, 63A, A3, British Standard Fuse, gG - gM, 550V ac BAO63M80
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 5,840
USD: 36.61
-
Cooper Bussmann, 63A, A3, British Standard Fuse, gG - gM, 550V ac BAO63M100
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 2,350
USD: 14.73
-
Cooper Bussmann, 100M125A, A4, British Standard Fuse, gG - gM, 415V ac CEO100M125
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,920
USD: 24.57
-
Cooper Bussmann, 100A, A4, British Standard Fuse, gG - gM, 415V ac CEO100M160
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,930
USD: 24.64
-
Cooper Bussmann, 125A, B2, British Standard Fuse, gG, 415V ac DD125
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 7,450
USD: 46.70
-
Cooper Bussmann, 160A, B2, British Standard Fuse, gG, 415V ac DD160
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 4,240
USD: 26.58
-
Cooper Bussmann, 200A, B2, British Standard Fuse, gG, 415V ac DD200
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 4,080
USD: 25.58
-
Cooper Bussmann, 200A, B2, British Standard Fuse, gG - gM, 415V ac DD200M250
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 5,630
USD: 35.29
-
Cooper Bussmann, 100A, FEE, FF, British Standard Fuse, 660V ac 100FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 68,800
USD: 431.27
-
Cooper Bussmann, 120A, FEE, FF, British Standard Fuse, 690V 120FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 7,510
USD: 47.08
-
Cooper Bussmann, 140A, FEE, FF, British Standard Fuse, 690V 140FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 7,880
USD: 49.40
-
Cooper Bussmann, 160A, FEE, FF, British Standard Fuse, 690V 160FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 8,380
USD: 52.53
-
Cooper Bussmann, 180A, FM, FF, British Standard Fuse, 660V ac 180FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 7,880
USD: 49.40
-
Cooper Bussmann, 200A, FM, FF, British Standard Fuse, 660V ac 200FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 8,470
USD: 53.09
-
Cooper Bussmann, 250A, FM, FF, British Standard Fuse, 660V ac 250FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 9,280
USD: 58.17
-
Cooper Bussmann, 315A, FM, FF, British Standard Fuse, 660V ac 315FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 11,000
USD: 68.95
-
Cooper Bussmann, 350A, FM, FF, British Standard Fuse, 660V ac 350FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 11,000
USD: 68.95
- AXEL GLOBAL
- CategoriesList of 【Cooper Bussmann】Fuses="preload" href="/en/asone/css/slider.css?v=03790be0f2ba82c1280907a7033cf49dabaaa7c1" as="style">
<!--@[ss-47]@-->[$1]【Cooper Bussmann】Fuses[/$1]一覧<!--@/[ss-47]@--> 【AXEL GLOBAL】ASONE Contact us
[Cooper Bussmann]Fuses
Filters
Result: 262product groups- by Product group
- by Product
Sort by:
-
Cooper Bussmann, 750mA Glass Cartridge Fuse, 6.3 x 32mm, Speed T TDC11-750MA
All fuses 6.3mm (0.25in) diameter and 32mm (1.25in) in length. Glass Body - (T) LBC. Glass tube fuses are available in with fast acting and time delay characteristics which makes them suitable for a variety of different applications. Glass cartridge fuses are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass cartridge 6.3mm x 21 mm cartridge size T Speed Rating Low Breaking Capacity Typical applications: Cartridge fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances such as motors air-conditions, refrigerator, pumps etc. They can be found in the following areas: Industrial Commercial Home/Residential Automotive Additional Information: What size is it? 6.3 x 32mm is a miniature cartridge size. Miniature fuses are ideal for the protection of electrical appliances, electronic equipment and component parts. Why choose a glass fuse? Glass and ceramic fuses have similar properties. However you may choose a glass fuse as it enables you to see the inside of the fuse. Therefore it is easier to determine whether the fuse has blown. What are fuses used for? For the protection of components and equipment from costly damage caused by over-current. To isolate sub-systems from the main system once a fault has appeared What is an over-current? It is a setting where a circuit experiences a current that is higher than the normal operating current. What Speed is it? This particular fuse is T speed rated which means it is a slow acting fuse, sometimes referred to as anti-surge. It is able to tolerate higher levels for a short period, without shorting. Therefore, if a sudden change occurs, this fuse will not blow immediately. They are suitable for applications where a sudden flow of high current is required. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity).
1 products found
JPY: 313,000
USD: 1,962.01
-
Cooper Bussmann, 250mA Glass Cartridge Fuse, 6.3 x 32mm, Speed F TDC10-250MA
Quick Acting (F) LBC Glass Cartridge Fuse. This glass cartridge fuse is ideal for providing protection to devices or internal circuits. They are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass tube, electroplated brass endcap construction 6.3 x 32 mm cartridge size F Speed Rating RoHS compliant and lead-free Interrupting rating equals 10 times rated current Typical applications: Miniature fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances, electronic equipment and component parts More information: Why choose a glass fuse? Glass and ceramic fuses have similar properties. Glass fuse is great for small items that don't draw a heavy amount of current and blow on a regular basis. It is easy to identify whether the fuse has blown as you can see inside it. What size is it? 6.3 x 32 mm is a standard cartridge size and it measures approximately 32 mm long by 6.3 mm in diameter. They are popular in board and panel protection and will fit a compatible 6.3 x 32 fuse holder. What Speed is it? This particular fuse is ''F'' speed rated which means a fast acting fuse. These are designed to protect less sensitive components and are also used to protect cabling from melting or catching fire when an overload appear. Every fast acting fuse will have the exact speed stated which will be relevant to different overloads. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity). What are fuses used for? For the protection of components and equipment from costly damage caused by over-current To isolate sub-systems from the main system once a fault has appeared What is an overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 125,000
USD: 783.55
-
Cooper Bussmann, 500mA Glass Cartridge Fuse, 6.3 x 32mm, Speed F TDC10-500-R
Quick Acting (F) LBC Glass Cartridge Fuse. This glass cartridge fuse is ideal for providing protection to devices or internal circuits. They are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass tube, electroplated brass endcap construction 6.3 x 32 mm cartridge size F Speed Rating RoHS compliant and lead-free Interrupting rating equals 10 times rated current Typical applications: Miniature fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances, electronic equipment and component parts More information: Why choose a glass fuse? Glass and ceramic fuses have similar properties. Glass fuse is great for small items that don't draw a heavy amount of current and blow on a regular basis. It is easy to identify whether the fuse has blown as you can see inside it. What size is it? 6.3 x 32 mm is a standard cartridge size and it measures approximately 32 mm long by 6.3 mm in diameter. They are popular in board and panel protection and will fit a compatible 6.3 x 32 fuse holder. What Speed is it? This particular fuse is ''F'' speed rated which means a fast acting fuse. These are designed to protect less sensitive components and are also used to protect cabling from melting or catching fire when an overload appear. Every fast acting fuse will have the exact speed stated which will be relevant to different overloads. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity). What are fuses used for? For the protection of components and equipment from costly damage caused by over-current To isolate sub-systems from the main system once a fault has appeared What is an overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 228,000
USD: 1,429.20
-
Cooper Bussmann, 150mA Glass Cartridge Fuse, 6.3 x 32mm, Speed T TDC11-150MA
All fuses 6.3mm (0.25in) diameter and 32mm (1.25in) in length. Glass Body - (T) LBC. Glass tube fuses are available in with fast acting and time delay characteristics which makes them suitable for a variety of different applications. Glass cartridge fuses are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass cartridge 6.3mm x 21 mm cartridge size T Speed Rating Low Breaking Capacity Typical applications: Cartridge fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances such as motors air-conditions, refrigerator, pumps etc. They can be found in the following areas: Industrial Commercial Home/Residential Automotive Additional Information: What size is it? 6.3 x 32mm is a miniature cartridge size. Miniature fuses are ideal for the protection of electrical appliances, electronic equipment and component parts. Why choose a glass fuse? Glass and ceramic fuses have similar properties. However you may choose a glass fuse as it enables you to see the inside of the fuse. Therefore it is easier to determine whether the fuse has blown. What are fuses used for? For the protection of components and equipment from costly damage caused by over-current. To isolate sub-systems from the main system once a fault has appeared What is an over-current? It is a setting where a circuit experiences a current that is higher than the normal operating current. What Speed is it? This particular fuse is T speed rated which means it is a slow acting fuse, sometimes referred to as anti-surge. It is able to tolerate higher levels for a short period, without shorting. Therefore, if a sudden change occurs, this fuse will not blow immediately. They are suitable for applications where a sudden flow of high current is required. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity).
1 products found
JPY: 517,000
USD: 3,240.77
-
Cooper Bussmann, 250mA Glass Cartridge Fuse, 6.3 x 32mm, Speed T TDC11-250MA
All fuses 6.3mm (0.25in) diameter and 32mm (1.25in) in length. Glass Body - (T) LBC. Glass tube fuses are available in with fast acting and time delay characteristics which makes them suitable for a variety of different applications. Glass cartridge fuses are ideal for providing protection to devices or internal circuits from short circuits and overcurrent. They are deliberately weaker components which, when too much current is drawn, will blow. Once the fuse has blown it will need replacing in order to make the circuit complete and allow the flow of current. Features: Glass cartridge 6.3mm x 21 mm cartridge size T Speed Rating Low Breaking Capacity Typical applications: Cartridge fuses are a relatively cheap way of protecting electrical equipment from short circuits and overcurrent and can be used to protect electrical appliances such as motors air-conditions, refrigerator, pumps etc. They can be found in the following areas: Industrial Commercial Home/Residential Automotive Additional Information: What size is it? 6.3 x 32mm is a miniature cartridge size. Miniature fuses are ideal for the protection of electrical appliances, electronic equipment and component parts. Why choose a glass fuse? Glass and ceramic fuses have similar properties. However you may choose a glass fuse as it enables you to see the inside of the fuse. Therefore it is easier to determine whether the fuse has blown. What are fuses used for? For the protection of components and equipment from costly damage caused by over-current. To isolate sub-systems from the main system once a fault has appeared What is an over-current? It is a setting where a circuit experiences a current that is higher than the normal operating current. What Speed is it? This particular fuse is T speed rated which means it is a slow acting fuse, sometimes referred to as anti-surge. It is able to tolerate higher levels for a short period, without shorting. Therefore, if a sudden change occurs, this fuse will not blow immediately. They are suitable for applications where a sudden flow of high current is required. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or rupturing. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. This particular fuse is LBC (Low Breaking Capacity).
1 products found
JPY: 714,000
USD: 4,475.65
-
Cooper Bussmann, 32A, A2, British Standard Fuse, gG - gM, 550V ac AAO32M40
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,580
USD: 22.44
-
Cooper Bussmann, 32A, A2, British Standard Fuse, gG - gM, 550V ac AAO32M50
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,580
USD: 22.44
-
Cooper Bussmann, 32A, A2, British Standard Fuse, gG - gM, 550V ac AAO32M63
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,980
USD: 24.95
-
Cooper Bussmann, 63A, A3, British Standard Fuse, gG - gM, 550V ac BAO63M80
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 5,840
USD: 36.61
-
Cooper Bussmann, 63A, A3, British Standard Fuse, gG - gM, 550V ac BAO63M100
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 2,350
USD: 14.73
-
Cooper Bussmann, 100M125A, A4, British Standard Fuse, gG - gM, 415V ac CEO100M125
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,920
USD: 24.57
-
Cooper Bussmann, 100A, A4, British Standard Fuse, gG - gM, 415V ac CEO100M160
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 3,930
USD: 24.64
-
Cooper Bussmann, 125A, B2, British Standard Fuse, gG, 415V ac DD125
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 7,450
USD: 46.70
-
Cooper Bussmann, 160A, B2, British Standard Fuse, gG, 415V ac DD160
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 4,240
USD: 26.58
-
Cooper Bussmann, 200A, B2, British Standard Fuse, gG, 415V ac DD200
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 4,080
USD: 25.58
-
Cooper Bussmann, 200A, B2, British Standard Fuse, gG - gM, 415V ac DD200M250
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 5,630
USD: 35.29
-
Cooper Bussmann, 100A, FEE, FF, British Standard Fuse, 660V ac 100FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 68,800
USD: 431.27
-
Cooper Bussmann, 120A, FEE, FF, British Standard Fuse, 690V 120FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 7,510
USD: 47.08
-
Cooper Bussmann, 140A, FEE, FF, British Standard Fuse, 690V 140FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 7,880
USD: 49.40
-
Cooper Bussmann, 160A, FEE, FF, British Standard Fuse, 690V 160FEE
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 8,380
USD: 52.53
-
Cooper Bussmann, 180A, FM, FF, British Standard Fuse, 660V ac 180FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 7,880
USD: 49.40
-
Cooper Bussmann, 200A, FM, FF, British Standard Fuse, 660V ac 200FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 8,470
USD: 53.09
-
Cooper Bussmann, 250A, FM, FF, British Standard Fuse, 660V ac 250FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 9,280
USD: 58.17
-
Cooper Bussmann, 315A, FM, FF, British Standard Fuse, 660V ac 315FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 11,000
USD: 68.95
-
Cooper Bussmann, 350A, FM, FF, British Standard Fuse, 660V ac 350FM
Fast Acting (FF) HRC Power Fuses. Compact dimensions Excellent current limiting features High speed clearance of ac and dc faults Melt Point Curve Class IEC 269-4 Manufactured by Cooper Bussmann, branded ‘Bussmann ‘ Certified to BS88: Part 4 (IEC 269: Part 4). Note that in the table below I ;sup>2 ;/sup>t is the pre-arcing value; I ;sup>2 ;/sup>t Total is the clearing value at 240Vac
1 products found
JPY: 11,000
USD: 68.95
-
Cooper Bussmann 25A A1 British Standard Fuse, gG, 550V ac NITD25
Low Voltage Fuses. Rated up to 550Vac (SSD types 240Vac/120Vdc) Low power loss, typically 20% lower than the requirements of BS88 Suitable for type 2 co-ordinated applications as defined in IEC 947-4 Suitable for three-phase applications General purpose (gG) and dual motor rated (gM) types Time/current characteristics (IEC 269) Low temperature rise, suitable for high density mounting applications ASTA, BS88 and IEC269 certified
1 products found
JPY: 2,100
USD: 13.16
-
Cooper Bussmann, 100mA Melamine Cartridge Fuse, 10 x 38mm, Speed F KTK1-1/10
UL listed, CSA certified. 10 x 38 Fast Acting, KTK Series. American Midget style 10x38mm fuses. Ideal for use in circuits with high a.c. fault current capacity 100kA breaking capacity Voltage rating 600Vac Typical Applications: Control circuits, Lighting circuit protection, meter circuits.
1 products found
JPY: 7,200
USD: 45.13
-
Cooper Bussmann, 5A Melamine Cartridge Fuse, 10 x 38mm, Speed F KTK-5
UL listed, CSA certified. 10 x 38 Fast Acting, KTK Series. American Midget style 10x38mm fuses. Ideal for use in circuits with high a.c. fault current capacity 100kA breaking capacity Voltage rating 600Vac Typical Applications: Control circuits, Lighting circuit protection, meter circuits.
1 products found
JPY: 60,800
USD: 381.12
-
Cooper Bussmann, 7A Melamine Cartridge Fuse, 10 x 38mm, Speed F KTK-7
UL listed, CSA certified. 10 x 38 Fast Acting, KTK Series. American Midget style 10x38mm fuses. Ideal for use in circuits with high a.c. fault current capacity 100kA breaking capacity Voltage rating 600Vac Typical Applications: Control circuits, Lighting circuit protection, meter circuits.
1 products found
JPY: 34,500
USD: 216.26
-
Cooper Bussmann, 3A Melamine Cartridge Fuse, 10 x 38mm, Speed F KTK-3
UL listed, CSA certified. 10 x 38 Fast Acting, KTK Series. American Midget style 10x38mm fuses. Ideal for use in circuits with high a.c. fault current capacity 100kA breaking capacity Voltage rating 600Vac Typical Applications: Control circuits, Lighting circuit protection, meter circuits.
1 products found
JPY: 59,500
USD: 372.97
-
Cooper Bussmann, 12A Ceramic Cartridge Fuse, 10 x 38mm PV-12A10F
Bussmann Cylindrical Photovoltaic Fuses. Cooper Bussmann PV fuses are specifically designed for protection and isolation of photovoltaic strings. These fuses are designed for use in systems with extreme ambient temperatures and offer low watts loss performance for energy efficiency. PV fuses work in high cycling and low fault conditions, reverse current, multi-array fault and string arrays.
1 products found
JPY: 13,400
USD: 84.00
-
Cooper Bussmann, 500mA Ceramic Cartridge Fuse, 10 x 38mm C10G0-5
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 4,380
USD: 27.46
-
Cooper Bussmann, 12A Ceramic Cartridge Fuse, 10 x 38mm C10G12
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 2,000
USD: 12.54
-
Cooper Bussmann, 2A Ceramic Cartridge Fuse, 14 x 51mm C14G2
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 2,670
USD: 16.74
-
Cooper Bussmann, 4A Ceramic Cartridge Fuse, 14 x 51mm C14G4
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 2,640
USD: 16.55
-
Cooper Bussmann, 10A Ceramic Cartridge Fuse, 14 x 51mm C14G10
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 6,280
USD: 39.37
-
Cooper Bussmann, 32A Ceramic Cartridge Fuse, 14 x 51mm C14G32
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 2,560
USD: 16.05
-
Cooper Bussmann, 25A Ceramic Cartridge Fuse, 14 x 51mm C14G25
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 2,560
USD: 16.05
-
Cooper Bussmann, 32A Ceramic Cartridge Fuse, 22.2 x 58mm C22G32
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 4,770
USD: 29.90
-
Cooper Bussmann, 50A Ceramic Cartridge Fuse, 22.2 x 58mm C22G50
IEC Cylindrical Fuses. Our range of products is available for domestic applications. These ceramic fuses are also available with an optional visual indicator. Fuse links comply with IEC60269-1, 60269-3, 60269-3-1 and also meet the requirements of NF and UNE standards. What material are these made from? All series of cylindrical fuse links have ceramic bodies and silverplated copper end caps. Why choose ceramic cartridge fuse? Ceramic and glass cartridge fuses have similar properties. The capacity of a ceramic cartridge fuse is higher than other fuses, which means that ceramic fuses can be used in circuits that have a higher current. They are perfect for protecting against overheating. What size is it? Sizes 8 x 32 mm, 10x38 mm, 14x51 mm ; 22x58 mm in both Class gL-gG and aM are also available with a built-in striker for micro-switch operation and remote indication. Class gL-gG and aM fuse links are intended for industrial applications. All industrial fuse links are available with an operated visible fuse indicator. What voltage is it? This range of cylindrical fuses links is available in a wide selection of physical sizes and current ratings for applications where the system voltage is 400, 500 and 690 Volts AC. What is Breaking Capacity? Breaking capacity is the level of current that the fuse can safely handle without exploding or breaking. The breaking capacity of your fuse should be greater than the fault current of your electronic circuit. What are fuses used for? For the protection of components and equipment from costly damage used by over-current To isolate sub-systems from the main system once a fault has appeared What is on overcurrent? It is a setting where a circuit experiences a current that is higher than the normal operating current.
1 products found
JPY: 4,890
USD: 30.65
