Tektronix

Tektronix Mixed Signal Oscilloscope GPIB to USB Adapter, Model TEK USB-488 for use with DPO4000 Series　TEK-USB-488

Adapters, 2 USB Cables, User Manual • GPIB and USB Adapters • The TEK-USB-488 is an adapter for communication between a GPIB bus controller and the USB port of a Tektronix instrument that conforms to the USBTMC-USB488 standard.
GPIB control of Tektronix instrument via USB port on Tektronix instrument USBTMC-USB488 standard compliant GPIB primary address can be set from host Tektronix instrument Power from USB host or optional external power supply LED indicator displays power, adapter status, USB status

Tektronix

Tektronix Oscilloscope Module ADA400A, For Use With TDS400 Series, TDS500 Series, TDS5000 Series, TDS600 Series, TDS700　ADA400A

Tektronix ADA400A 1 MHz Differential Preamplifier. The ADA400A Active Differential Preamplifier allows direct oscilloscope measurements of very low amplitude voltages and signals which are not ground referenced. The high impedance of both inputs eliminates the need to add additional ground points in the DUT, thereby avoiding circulating currents which disturb the measurement or the circuit.,The high gain and extremely high common mode rejection provide usable measurements of voltages as low as 5μV, even in high noise environments. Selectable bandwidth limiting reduces normal mode noise from digital logic, switch mode power supplies and line frequency sources. Adjustable differential offset allows the user to null out transducer bridge bias and galvanic potential from the test set-up. An "infinite impedance" mode can be selected in the two highest gain ranges allowing accurate measurements of signals with high source impedance. It is specifically designed to operate on Tektronix oscilloscopes with TEKPROBE® interface. 10μV/div Sensitivity Low-pass filter: 100Hz, 3kHz, 100Hz or Full (1 MHz) Typically 100 dB CMRR DC to 10 kHz Selectable Gain: 100, 10, 1 or 0.1 Accurately measures signal as small as 5uV Integral Probe Power with TEKPROBE™BNC

Tektronix

Tektronix P6245 Oscilloscope Probe, Probe Type: Active 1.5GHz 1:10　P6245

P6245 Active FET Probe. Solves three longstanding problems by providing: lower DUT loading (≤1 pF/1 MΩ probe loading); direct and easy access to SMDs; accesses DUT signals and scope bandwidth for TDS600/700/3000/5000/6000/7000*1 and CSA7000 scopes up to 1 GHz bandwidths. Provides the electrical and mechanical performance required for today's digital systems designs. No additional power supplies or cables are required when used with TEKPROBE BNC oscilloscopes. Achieves high-speed signal acquisition and low circuit loading. The small compact probe head and versatile attachment accessories allow direct connection to the device under test. Provides scope bandwidth at the probe tip for the TDS500/600/700 ≥1.5 GHz bandwidth (typical, probe only) ≤1 pF input capacitance 1 MΩ input resistance Direct access to SMDs as small as 0.5 mm pitch Measures CMOS, BiCMOS, ECL, GaAs and TTL Logic

Tektronix

Tektronix TDP1000 Oscilloscope Probe, Probe Type: Differential, High Voltage 1GHz 30V 1:5, 1:50　TDP1000

Tektronix TDP0500, TDP1000. For high-speed switch mode power supply design; CAN/LIN bus design; high-speed digital design; digital design and characterization; manufacturing engineering test; research and development. ±42 V (DC + pk AC) differential input voltage 18 dB CMRR (at 250 MHz 50X attenuation) Selectable bandwidth limiting filters DC reject Connects to some Tektronix oscilloscopes using the TekVPI™ probe interface Easy access to scope-displayed probe menu for probe setup control and operating status information Auto-Zero – nulls output offset

Tektronix

Tektronix Mixed Signal Oscilloscope Signal Adapter, Model TCABNC for use with TDS6000 Series, TDSCSA7000B Series　TCA-BNC

Tektronix TekConnect TCA Series Adaptors. These adaptors, available separately, provide less signal distortion and better performance than traditional connections used to move a signal from one environment to another, such as BNC to N or BNC to SMA.,TCA75 Adaptor (75 to 50Ω),Allows Tektronix oscilloscopes with TekConnect interface to easily access and measure 75Ω terminated circuitry. The TCA75's attenuation factor is automatically corrected to provide the end user with correctly displayed signal magnitudes.,TCA-BNC Adaptor (50Ω only),A direct 50Ω input with TekProbe BNC 50 Ω capability, this adaptor may be used as a direct 50Ω BNC input or with Tektronix high-speed active and differential probes requiring the TekProbe BNC 50Ω interface.,TCA-SMA and TCA-N Adaptors (50Ω only),These high-speed adaptors allow a more direct connection to the signal under test requiring N or SMA connections, without losing performance by adding other external conversion adaptors.,Applications include: signal integrity, jitter and timing analysis; verification, characterization and debug; high-speed digital devices and circuits; power supplies/inverters; semiconductor devices; electronic ballasts; industrial/consumer electronics; mobile communications; motor drives; transportation systems; disk drive analysis; investigation of transient phenomena; spectral analysis; video design and development; HDTV and streaming digital video; 3 Gbps HD-SDI.

Tektronix

Tektronix TPP0100 Oscilloscope Probe, Probe Type: Passive 100MHz 300V 1:10　TPP0100

Retractable hook tip, ground spring, ground lead with alligator clip. Tektronix 100MHz Passive Probes TPP0100 & TPP0101. For use on BNC oscilloscopes with 1MΩ/13pF (TPP0100) and 1MΩ/20pF (TPP0101) inputs.

Tektronix

Tektronix TCP305A Oscilloscope Probe, Probe Type: Current 50MHz　TCP305A

Tektronix TCP Series. The Tektronix TCP300 Series of split-core current probes incorporates transformer and Hall effect technology. The TCP300 models TCP303 (< 796-2683') 796-2683/ ), TCP305A ( < 781-0810') 781-0810/ ) and TCP312A ( < 781-0801') 781-0801/ ) are used with amplifier TCPA300 ( < 764-4391') 764-4391/ ), available separately, to provide high performance capability from low level milliamp measurements to the measurement of very high current levels. The TCP0030A ( < 781-0807') 781-0807/ ) is powered directly by oscilloscopes with the TekVPI interface. Easy-to-use and accurate AC/DC current measurements Connects to some Tektronix oscilloscopes using the TekVPI™ probe interface Provides automatic units scaling and readout on the oscilloscope display Split-core construction allows easy circuit connection Typically less than 1% DC gain error Low Noise and DC Drift Easy to Degauss and Autozero Setup controls and probe status/diagnostic indicators on probe hardware and via oscilloscope UI display menu

Tektronix

Tektronix AFG31021 Function Generator & Counter 25MHz　AFG31021

Tektronix

Tektronix AFG31022 Function Generator & Counter 25MHz　AFG31022

Tektronix

Tektronix AFG31051 Function Generator & Counter 50MHz　AFG31051

Tektronix

Tektronix AFG31052 Function Generator & Counter 50MHz　AFG31052

Tektronix

Tektronix AFG31101 Function Generator & Counter 100MHz　AFG31101

Tektronix

Tektronix AFG31102 Function Generator & Counter 100MHz　AFG31102

Tektronix

Tektronix TDP1500 Oscilloscope Probe, Probe Type: Active, Differential 1.5GHz 25V 1:1, 1:10　TDP1500

Tektronix TDP1500, TDP3500. For design, validation, debugging and characterization of common high-speed serial bus designs including I 2 C, CAN/LIN, SPI, Serial ATA, Ethernet (GbE), USB 2.0, FireWire (1394b); signal integrity, jitter and timing analysis; manufacturing engineering and test. Accurate measurements for serial and digital applications Excellent common mode rejection - reduces measurement errors in higher common environments Low capacitive and resistive loading - maintains signal fidelity and reduces DC biasing interactions Connects to some Tektronix oscilloscopes using the TekVPI™ probe interface < 661-3302') 661-3302/

Tektronix

Tektronix TPP0850 Oscilloscope Probe, Probe Type: High Voltage, Passive 800MHz 1kV 1:50　TPP0850

Tektronix MSO/DPO 4000/5000 Accessories

Tektronix

Tektronix P5202A Oscilloscope Probe, Probe Type: Differential, High Voltage 100MHz 640V 1:20, 1:200　P5202A

TMDP and THDP Series probes have the TekVPI® interface which enables smart communication between oscilloscope and probe - each TekVPI probe features controls and indicators located on the probe compensation box, designed to provide quick and easy access to the probe's most commonly required setup controls and operating status. P52xxA Series probes have the Tektronix TekProbe® interface which communicates scale information to the oscilloscope. Tektronix high voltage differential probes include: TMDPO200 ( < 752-7366') 752-7366/ ); THDPO200 ( < 752-7357') 752-7357/ ); THDP0100 ( < 752-7353') 752-7353/ ); P5200A ( < 734-5029') 734-5029/ ); P5202A ( < 734-5022') 734-5022/ ); P5205A ( < 734-5026') 734-5026/ ); P5210A ( < 734-5035') 734-5035/ ). Tektronix High Voltage Differential Probes TMDP, THDP and P52xxA Series. Tektronix high voltage probing solutions offer safety and accuracy in applications which include: floating measurements; switching power supply design; motor drive design; electronic ballast design; CRT display design; power converter design and service; power device evaluation. Overrange indicator Safety certified Switchable attenuation Switchable bandwidth limit Cable length 1.5m (THDP & TMDP), 1.8m (P52xxA)

Tektronix

Tektronix P6247 Oscilloscope Probe, Probe Type: Differential 1GHz 25V 1:1, 1:10　P6247

Tektronix Differential Probes P6246, P6247, P6248. Tektronix differential probes P6246, P6247 & P6248 enable users to make time-domain or frequency-domain measurements on high-bandwidth signals commonly found in disk drive, digital IC design (RAMBUS) and communication applications (Gigabit Ethernet, IEEE-1394 Firewire and Fibre Channel). The P6248 comes with accessories that allow RAMBUS via probing and IEEE-1394 interconnect access. All the probes have a small probe head geometry. They are supplied with probe tip accessories to accommodate manual probing of surface mount devices while maintaining high CMRR. They are popular choices for design verification of disk drive read channel electronics and timing analysis for troubleshooting ground bounce problems associated with high speed logic. Additional applications include pulse shape or cross talk compliance testing of high speed communication signals. For use with oscilloscopes, spectrum analyzers and network analyzers Low input capacitance <1 pF differential Probe input connector: two standard 0.025 in / 0.63 mm (0.1 in centre) square pin receptacle (female) Electrostatic discharge tolerant (IEC 801-2) >60 dB (1000:1) Common Mode Rejection Ratio (CMRR) Small probe head for easy probing of SMDs

Tektronix

Tektronix THDP0100 Oscilloscope Probe, Probe Type: Differential, High Voltage 100MHz 6kV 1:100, 1:1000　THDP0100

TMDP and THDP Series probes have the TekVPI® interface which enables smart communication between oscilloscope and probe - each TekVPI probe features controls and indicators located on the probe compensation box, designed to provide quick and easy access to the probe's most commonly required setup controls and operating status. P52xxA Series probes have the Tektronix TekProbe® interface which communicates scale information to the oscilloscope. Tektronix high voltage differential probes include: TMDPO200 ( < 752-7366') 752-7366/ ); THDPO200 ( < 752-7357') 752-7357/ ); THDP0100 ( < 752-7353') 752-7353/ ); P5200A ( < 734-5029') 734-5029/ ); P5202A ( < 734-5022') 734-5022/ ); P5205A ( < 734-5026') 734-5026/ ); P5210A ( < 734-5035') 734-5035/ ). Tektronix High Voltage Differential Probes TMDP, THDP and P52xxA Series. Tektronix high voltage probing solutions offer safety and accuracy in applications which include: floating measurements; switching power supply design; motor drive design; electronic ballast design; CRT display design; power converter design and service; power device evaluation. Overrange indicator Safety certified Switchable attenuation Switchable bandwidth limit Cable length 1.5m (THDP & TMDP), 1.8m (P52xxA)

Tektronix

Tektronix THDP0200 Oscilloscope Probe, Probe Type: Differential, High Voltage 200MHz 1.5kV 1:50, 1:500　THDP0200

TMDP and THDP Series probes have the TekVPI® interface which enables smart communication between oscilloscope and probe - each TekVPI probe features controls and indicators located on the probe compensation box, designed to provide quick and easy access to the probe's most commonly required setup controls and operating status. P52xxA Series probes have the Tektronix TekProbe® interface which communicates scale information to the oscilloscope. Tektronix high voltage differential probes include: TMDPO200 ( < 752-7366') 752-7366/ ); THDPO200 ( < 752-7357') 752-7357/ ); THDP0100 ( < 752-7353') 752-7353/ ); P5200A ( < 734-5029') 734-5029/ ); P5202A ( < 734-5022') 734-5022/ ); P5205A ( < 734-5026') 734-5026/ ); P5210A ( < 734-5035') 734-5035/ ). Tektronix High Voltage Differential Probes TMDP, THDP and P52xxA Series. Tektronix high voltage probing solutions offer safety and accuracy in applications which include: floating measurements; switching power supply design; motor drive design; electronic ballast design; CRT display design; power converter design and service; power device evaluation. Overrange indicator Safety certified Switchable attenuation Switchable bandwidth limit Cable length 1.5m (THDP & TMDP), 1.8m (P52xxA)

Tektronix

Tektronix TCP312A Oscilloscope Probe, Probe Type: Current 100MHz　TCP312A

Tektronix TCP Series. The Tektronix TCP300 Series of split-core current probes incorporates transformer and Hall effect technology. The TCP300 models TCP303 (< 796-2683') 796-2683/ ), TCP305A ( < 781-0810') 781-0810/ ) and TCP312A ( < 781-0801') 781-0801/ ) are used with amplifier TCPA300 ( < 764-4391') 764-4391/ ), available separately, to provide high performance capability from low level milliamp measurements to the measurement of very high current levels. The TCP0030A ( < 781-0807') 781-0807/ ) is powered directly by oscilloscopes with the TekVPI interface. Easy-to-use and accurate AC/DC current measurements Connects to some Tektronix oscilloscopes using the TekVPI™ probe interface Provides automatic units scaling and readout on the oscilloscope display Split-core construction allows easy circuit connection Typically less than 1% DC gain error Low Noise and DC Drift Easy to Degauss and Autozero Setup controls and probe status/diagnostic indicators on probe hardware and via oscilloscope UI display menu

Tektronix

Tektronix TCP0030A Oscilloscope Probe, Probe Type: Current 120MHz　TCP0030A

Tektronix TCP Series. The Tektronix TCP300 Series of split-core current probes incorporates transformer and Hall effect technology. The TCP300 models TCP303 (< 796-2683') 796-2683/ ), TCP305A ( < 781-0810') 781-0810/ ) and TCP312A ( < 781-0801') 781-0801/ ) are used with amplifier TCPA300 ( < 764-4391') 764-4391/ ), available separately, to provide high performance capability from low level milliamp measurements to the measurement of very high current levels. The TCP0030A ( < 781-0807') 781-0807/ ) is powered directly by oscilloscopes with the TekVPI interface. Easy-to-use and accurate AC/DC current measurements Connects to some Tektronix oscilloscopes using the TekVPI™ probe interface Provides automatic units scaling and readout on the oscilloscope display Split-core construction allows easy circuit connection Typically less than 1% DC gain error Low Noise and DC Drift Easy to Degauss and Autozero Setup controls and probe status/diagnostic indicators on probe hardware and via oscilloscope UI display menu

Tektronix

Tektronix AFG31000 Function Generator & Counter 250MHz　AFG31252

Tektronix

Tektronix AFG31000 Function Generator & Counter 250MHz　AFG31251

Tektronix

Tektronix AFG31000 Function Generator & Counter 150MHz　AFG31152

Tektronix