Omikogyo Co., Ltd.

Carbide Square Endmill (2 Blades Short, OES2S, Φ3 × Blade length 6mm) and others

Omikogyo Co., Ltd.

Endmill (Aluminum Processing, 2 Blades, OEA 2R, Φ3 × Blade length 9mm) and others

Omikogyo Co., Ltd.

Carbide Square Endmill (3 Blades Short, OES3S, Φ3 × Blade length 8mm) and others

Omikogyo Co., Ltd.

Carbide Endmill (Irregular Pitch & Irregularl Lead, 4 Blades, Φ3 × Blade length 6mm) and others

Omikogyo Co., Ltd.

Carbide Square Endmill (4 Blades, Short, Φ3 × Blade length 8mm) and others

Omikogyo Co., Ltd.

Carbide Endmill (High Hardness Steel, Φ3 × Blade Length: 10mm) and others

Omikogyo Co., Ltd.

Carbide Roughing Endmill (Φ5 x Blade Length: 15) and others

Omikogyo Co., Ltd.

Carbide Roughing Endmill (Fine Pitch,, Φ5 x Blade Length: 10) and others

Omikogyo Co., Ltd.

Carbide Drill (Steel, Short, 3D Type, External Lubrication Type, Φ3.0 x Blade length 15 x Total length 52mm) and others

Omikogyo Co., Ltd.

Carbide Drill (Steel, Regular, 5D Type, Internal Lubrication Type, Φ3.0 × Blade length 21 × Total length 58mm) and others

Omikogyo Co., Ltd.

V Carbide Drill (Short, Φ3.0 x Blade length 20 x Total length 60mm) and others

Omikogyo Co., Ltd.

Core Bit (Plaster Board, Φ6 x Total length 94 x Shank Diameter 6.35mm)　BB-6

With the reverse spiral blade (made of high speed), the gypsum board which has not been cut cleanly on both sides can be cut cleanly on this side.
You can cut out the plate by freehand, so you can cut round holes, square holes, and curves.

Omikogyo Co., Ltd.

Carbide Panel Bit (Φ6 x Total length 53 x Shank Diameter 6.35mm)　TP-6

You can cut out the plate by freehand, so you can cut round holes, square holes, and curves.
With an electric drill, veneer plywood can be about 15 mm thick and gypsum board can be up to 20 mm thick.

Omikogyo Co., Ltd.

Drill (For FRP, Φ6.0 × Blade length 60 × Total length 100mm) and others

Omikogyo Co., Ltd.

Spiral Step Drill (Φ4 to 30.5mm, Number of Steps: 10, Step Width: 5mm) and others

Omikogyo Co., Ltd.

Spiral Step Drill (Hex-Axis, 2 Blades, Φ4 to 12mm, Number of Steps: 9, Step Width: 4.0mm) and others

Omikogyo Co., Ltd.

Step Drill (Pilot Hole For Tap, M4, M5, and M6) and others

Omikogyo Co., Ltd.

Step Drill (For Roof, 12.5mm) and others

Omikogyo Co., Ltd.

Drill Bit (Φ3.5 For Galvanized Steel Plate)　GB35

Cut the outer wall material with the high blade + titanium coating.
Work Material: Galva steel plate, tin, galvanized iron, aluminum spandrel.

Omikogyo Co., Ltd.

Roof Drill With Sheath (Φ12.5) and others

Omikogyo Co., Ltd.

Extension Bar For Drill Chuck (Φ10mm, 450mm)　DC450K

Extend the blade and bit by 450 mm.
Can be reversed and the drill chuck part can be replaced.

Omikogyo Co., Ltd.

Extension Bar (For Step Drill, Φ6.35, 450mm) and others

Omikogyo Co., Ltd.

HSS Cutter (25 SQ, 18.0 x Maximum Processing Thickness: 25 Weight 90g) and others

Omikogyo Co., Ltd.

Shank Set (For 35 S, MT2) and others

Omikogyo Co., Ltd.

Crinkey Cutter (50 SQ, 51.0 x Maximum Processing Thickness: 50 Weight 300g) and others

Omikogyo Co., Ltd.

Crinkey Cutter (50 H, 17.5 x Maximum Processing Thickness: 50 Weight 100g) and others

Omikogyo Co., Ltd.

Carbide Hole Cutter (Stainless Steel, 14mm) and others

Omikogyo Co., Ltd.

FA Hole Cutter (Φ15mm) and others

Omikogyo Co., Ltd.

Carbide Hole Cutter (Long, Φ15mm) and others

Omikogyo Co., Ltd.

Hole Cutter (FRP, Φ20mm) and others

Omikogyo Co., Ltd.

Exhauster (FRP 30 to 47) and others

Omikogyo Co., Ltd.

SL Hole Cutter (Φ12mm) and others

Omikogyo Co., Ltd.

FCL Hole Cutter (No Brim, Long, Φ21mm) and others

Omikogyo Co., Ltd.

SP Hole Cutter (Φ53mm, Applicable Pipe: 40mm) and others

Omikogyo Co., Ltd.

Diamond Cutter (Porcelain Tiles, Φ25mm) and others

Omikogyo Co., Ltd.

E-Type Hole Cutter (Φ10.5mm) and others

Omikogyo Co., Ltd.

G-Type Hole Cutter (Φ12mm) and others

Omikogyo Co., Ltd.

FX Hole Cutter (Φ15mm) and others

Omikogyo Co., Ltd.

Dual Hole Cutter (Φ28mm) and others

Omikogyo Co., Ltd.

DHS Hole Cutter (Φ21mm) and others