[SparkFun] 所有产品
实验室仪器和用品
-
调色剂
-
分析仪器
-
自动稀释器
-
解剖工具和用品
-
手套 (PVC)
-
Digital Products
公告供应
-
隔膜泵
-
塑料购物袋/塑料购物袋
-
春节
-
排水管清洁器
-
小型工作台
外来物质污染控制
-
浓度计
林特
-
Office Supply
-
-
-
-
-
One Wire Digital Temperature Sensor - DS18B20 SEN-00245
1找到 产品
JPY: 1,080
USD: 6.77
-
-
-
-
SparkFun Audio Jack Breakout PRT-10588
The Audio Jack Breakout is a board for connecting a 3.5 mm audio jack. Five pins are pulled out, and can be connected to a breadboard or printed circuit board by soldering pin headers.
1找到 产品
JPY: 430
USD: 2.70
-
SparkFun Logic Level Converter - Bi-Directional BOB-12009
1找到 产品
JPY: 1,070
USD: 6.71
-
-
-
-
-
Raspberry Pi GPIO Ribbon Cable -40 pin, 6inch (RPi2, B+) CAB-13028
1找到 产品
JPY: 1,330
USD: 8.34
-
SparkFun Servo Trigger WIG-13118
Servo Trigger is a board that allows easy control of RC servo motors such as small robots. The servo trigger of an external switch or logic signal can direct the connected servo motor to move from position A to position B. To use a servo trigger, use the onboard semi-fixed resistor to adjust the start/stop position and transition time.
An ATTiny84 microcontroller is used for control and a servo control program is executed. Each onboard servo trigger has three semi-fixed resistors. A sets the position where the servo enters when the switch is open, B sets the position where the servo moves when the switch is closed, and T sets the time it takes to return from A to B. There are two operating modes, which can be switched by the jumper (SJ1) on the back. The default is Bistable mode in which the switch is opened to A and closed to B. If the SJ1 is short-circuited, the switch is set to One shot mode in which AB and AB are repeated each time the switch is pressed.1找到 产品
JPY: 6,220
USD: 38.99
-
SparkFun gamer:bit DEV-14215
The gamer: bit is an expansion board for adding Famicom-like buttons and ports for external inputs. The edge connector makes it easy to connect to micro: bit. The left side of the board has a 4-way D-pad and the right side of the board has two action buttons. The two push buttons in the middle micro: bit act as Start and Select.
micro: bit is an ultra-small microcomputer board developed by the British Broadcasting Corporation (BBC) for the education of elementary school students.1找到 产品
JPY: 2,120
USD: 13.29
-
-
-
-
-
-
Arduino Pro Mini328-5V/16MHz DEV-11113
The Arduino Pro Mini328-5 V/16 MHz is a minimalist Arduino board with a 16 MHz boot loader. The operating voltage of the microcomputer is 5V. It has a regulator and a clock oscillator, and the minimum operation of a microcomputer is possible, but it omits the USB interface that full-spec Arduino such as Uno has as a standard, and it has an external FTDI interface board. Auto reset is supported only when the DTR connector of the external interface is enabled. According to the manufacturer's comments, users should get started with Uno R3 and use the Arduino Pro after familiarizing themselves with the specifications. (Does the name "Pro" mean "no beginners" ...)
1找到 产品
JPY: 3,150
USD: 19.75
-
Arduino Pro Mini328-3.3V/8MHz DEV-11114
The Arduino Pro Mini328-3.3 V/8 MHz is a minimalist Arduino board with an 8 MHz boot loader. The operating voltage of the microcomputer is 3.3 V, which is different from the standard 5 V. It has a regulator and a clock oscillator, and the minimum operation of a microcomputer is possible, but it omits the USB interface that full-spec Arduino such as Uno has as a standard, and it has an external FTDI interface board. Auto reset is supported only when the DTR connector of the external interface is enabled. The power supply voltage of the microcomputer is 3.3 V, so the voltage of the interface is also limited. According to the manufacturer's comments, users should get started with Uno R3 and use the Arduino Pro after familiarizing themselves with the specifications. (Does the name "Pro" mean "no beginners" ...)
1找到 产品
JPY: 3,200
USD: 20.06
-
-
FTDI Basic Breakout - 5V DEV-09716
Contents: USB to serial conversion board for ArduinoPro, mini and LilyPad with 5V supply voltage. Can be used with Arduinos that support automatic reset, eliminating the need to press the reset switch each time a sketch is written.
1找到 产品
JPY: 4,850
USD: 30.40
-
FTDI Basic Breakout-3.3V USB to Serial Adapter DEV-09873
Contents: USB to serial conversion board for ArduinoPro, mini and LilyPad with 3.3 V supply voltage. Can be used with Arduinos that support automatic reset, eliminating the need to press the reset switch each time a sketch is written.
There are also products with 5V power supply voltage.1找到 产品
JPY: 5,360
USD: 33.60
-
-
-
XBee Shield WRL-12847
Like Arduino Wireless Proto Shield and Arduino Wireless SD Shield, it provides logic level conversion between Arduino-XBee modules. (MOSFET) XBee radio module not included.
1找到 产品
JPY: 5,840
USD: 36.61
-
microSD Shield DEV-12761
*Pin header is not included. Please purchase separately.
1找到 产品
JPY: 4,710
USD: 29.52
-
XBeeExplorerUSB WRL-11812
This board enables USB connection of the XBee module to a personal computer. Equipped with a regulator IC to provide a 3.3 V power supply for the USB to Serial Conversion LSI, FT231X and XBee modules from 5 V USB bus power. It functions simply as a pitch conversion board which can be mounted on a 2.54 mm pitch breadboard, and all pins of the XBee module are connected to through holes for pin header mounting. (Pin headers are not implemented.) If you have this board, a mini-USB connection cable and a personal computer, you can set up with the X-CTU and run the XBee module.
1找到 产品
JPY: 8,650
USD: 54.22
-
SparkFun Transceiver Breakout - RS-485 BOB-10124
Breakout board to convert UART to RS-485
1找到 产品
JPY: 4,080
USD: 25.58
-
-
-
MyoWare sensor cable with three electrode pads CAB-12970
1找到 产品
JPY: 2,810
USD: 17.61
-
-
-
-
