65-1987-84 4 Flutes Unequally Divided Unequal Lead High-Efficiency Square End Mill, Outer Diameter 10 x Blade Length 50 x Total Length 100 x Shank Diameter 10 CXES4100-5000
คุณลักษณะ
- Vibration is suppressed by unequal division and unequal lead specifications.
- By adopting a high-toughness type that is hard to chip in cemented carbide, and by applying fine tuning such as a special groove shape, ultra-high-efficiency cutting that has never been achieved before is possible.
- It is possible to obtain a good finish surface not only in high-efficiency machining but also in finishing.
- The coating has a low friction type and provides excellent chip discharge and abrasion resistance.
- Shank taper angle is a guide.
- If it is necessary to interfere with the work, be sure to measure and confirm.
- Be careful of contact between the shank and the workpiece.
ข้อมูลจําเพาะ
- Blade diameter (mm): 10
- Blade length (mm): 50
- Total length (mm): 100
- Shank diameter (mm): 10
- Number of blades: 4
- Helix angle (degrees): 37 ~ 40
- Surface treatment: UTCOAT
- Compatible Work Materials: Carbon Steel, Alloy Steel, Pre-hardened Steel, Copper, Quenched (up to 55 HRC), Cast Iron, Titanium Alloy, Super Heat Resistant Alloy
- Material/Finish: Super MG
- Mass: 74 g
- Country of origin: Japan
- Securities Code: 217 -8713
| หมายเลขใบสั่ง | 65-1987-84 | |
|---|---|---|
| หมายเลขแบบจําลอง | CXES4100-5000 | |
| รหัส JAN | 4560295112544 | |
| ราคามาตรฐาน |
JPY: 15,700
USD: 97.69
Excange rate 1USD= 160.72JPY
Valid price in Japan |
|
| ปริมาณ | 1piece | |
| หุ้นในประเทศญี่ปุ่น |
|
|
| หุ้นซัพพลายเออร์ |
|
|
ผลิตภัณฑ์ที่เกี่ยวข้อง (ขนาดที่แตกต่างกัน, ข้อมูลจําเพาะ,ผลิตภัณฑ์ตัวเลือก ฯลฯ)
| รูปภาพผลิตภัณฑ์ | หมายเลขใบสั่ง | ชื่อ | หมายเลขแบบจําลอง | ปริมาณ | ราคามาตรฐาน | ราคาที่ถูกต้องในประเทศญี่ปุ่น | หุ้น [หุ้นซัพพลายเออร์] |
|
|---|---|---|---|---|---|---|---|---|
 |
65-1987-75 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 1 x Blade Length 5 x Total Length 60 x Shank Diameter 4 CXES4010-0500 | CXES4010-0500 | 1piece | JPY: 5,430 | USD: 33.79 |
|
|
 |
65-1987-76 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 2 x Blade Length 10 x Total Length 60 x Shank Diameter 4 CXES4020-1000 | CXES4020-1000 | 1piece | JPY: 5,080 | USD: 31.61 |
|
|
 |
65-1987-77 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 3 x Blade Length 15 x Total Length 60 x Shank Diameter 6 CXES4030-1500 | CXES4030-1500 | 1piece | JPY: 5,820 | USD: 36.21 |
|
|
 |
65-1987-78 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 4 x Blade Length 20 x Total Length 60 x Shank Diameter 6 CXES4040-2000 | CXES4040-2000 | 1piece | JPY: 6,110 | USD: 38.02 |
|
|
 |
65-1987-79 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 5 x Blade Length 25 x Total Length 70 x Shank Diameter 6 CXES4050-2500 | CXES4050-2500 | 1piece | JPY: 6,570 | USD: 40.88 |
|
|
 |
65-1987-80 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 6 x Blade Length 30 x Total Length 80 x Shank Diameter 6 CXES4060-3000 | CXES4060-3000 | 1piece | JPY: 7,400 | USD: 46.04 |
|
|
 |
65-1987-82 | 4-Flute Unequal Split Unequal Lead High-Efficiency Square End Mill, Outer Diameter 8 x Blade Length 40 x Total Length 90 x Shank Diameter 8 CXES4080-4000 | CXES4080-4000 | 1piece | JPY: 13,190 | USD: 82.07 |
|
|
 |
65-1987-84 | 4 Flutes Unequally Divided Unequal Lead High-Efficiency Square End Mill, Outer Diameter 10 x Blade Length 50 x Total Length 100 x Shank Diameter 10 CXES4100-5000 | CXES4100-5000 | 1piece | JPY: 15,700 | USD: 97.69 |
|
|
 |
65-1987-86 | 4 Flutes Unequally Divided Unequal Lead High-Efficiency Square End Mill, Outer Diameter 12 x Blade Length 60 x Total Length 120 x Shank Diameter 12 CXES4120-6000 | CXES4120-6000 | 1piece | JPY: 22,360 | USD: 139.12 |
|