Sakaguchi E.H VOC Corp.

67-6668-79　Polyimide Heater Samicon PI Type External Lead 100 x 100 100 V 100 W　PI-B1010

인쇄

시리즈 제품군 확인

제품 정보

English

기능

[High heat resistance] High heat resistance special polyimide film is used for the insulation that holds the heating wire, so it is a heater that can be used up to 250°C normally.
[Uniform temperature distribution] Since foil-shaped heating lines are evenly arranged on the heater surface and the heating area occupies a large portion of the heater surface area, it is a heater with low heating unevenness and high thermal efficiency.
[Environmentally Friendly] This is an eco-friendly heater that uses the characteristics of a thin heater to develop a terminal structure that does not use solder to connect the lead wire to the terminal.
[Low Outgassing] Since no adhesive is used for bonding insulators, this heater generates very little outgassing. In addition, since siloxane gas is not generated, it can be used in environments where the generation of siloxane gas is disliked.
[Fast Temperature Rising Response] Very thin insulator thickness of less than 0.2 mm and small heat capacity, this heater has especially fast temperature rising response of the heated object.

사양

Width x Length (mm): 100 x 100
External Lead (mm): 12.5 x 32
Lead length (mm): 200
Heater Surface Temperature: Normal 250°C (This is only a guide. The temperature that can be used may vary depending on the actual operating environment.)
Voltage: 100 V
Capacity: 100 W
Power density: (1) Suspended in still air: 1.0w/cm2 max. (2) Adhered to object to be heated: 1.5w/cm2 max.
Insulation resistance: 100 MΩ or more at 500 VDC mega
Thickness: 0.2 mm or less (excluding lead connection)
Precautions for Use
Do not use the product at a temperature higher than the specification limit. Be sure to control the temperature and use it at an appropriate temperature.
Do not repair, modify or disassemble the product by yourself.
Do not use in corrosive or high humidity environments.
Do not forcibly bend or pull the lead wire.
Do not bend the heater.
If there are any abnormalities such as smoke or strange smell, please stop using the heater immediately.
Store in a clean and dry place away from direct sunlight.
If the degree of adhesion to the object to be heated is low, an abnormally high temperature will occur, causing premature wire breakage.
Consult the manufacturer (Sakaguchi Electric Heating) when using by adhering to objects to be heated.
The joint of the lead wire is particularly vulnerable to external forces (Tension, bending, etc.).
Do not use multiple heaters.
WARNING: Mishandling of this product may cause electric shock, fire, or other accidents. Please observe the following precautions when using this product.
[Caution against ignition]
Never operate the product at a voltage higher than the rated voltage.
Do not use in flammable atmosphere as it is not explosion-proof.
Keep flammable materials away from the product.
[Electric shock caution]
Do not damage the heater surface and lead wires.
It's for indoor use only, and it's not waterproof. Do not let water, solution or steam come into contact with the heater.
[High temperature caution]
During or immediately after use, the heater and its peripherals are hot, so do not touch them until they have cooled sufficiently.

주문 번호	67-6668-79
모델 번호	PI-B1010
표준 가격	JPY: 29,000 USD: 181.91 Excange rate 1USD= 159.42JPY Valid price in Japan
수량	1sheet
일본의 주식
공급자 재고

다양한 상품군(多樣한) (다른 사이즈,다른 사양,옵션등)

제품 이미지	주문 번호	이름	모델 번호		수량	표준 가격	일본에서의 유효 가격	재고 [공급자 재고]
	67-6668-78	Polyimide Heater Samicon PI Type Internal Lead 100 x 100 100 V 100 W　PI-A1010	PI-A1010		1sheet	JPY: 28,000	USD: 175.64
	67-6668-79	Polyimide Heater Samicon PI Type External Lead 100 x 100 100 V 100 W　PI-B1010	PI-B1010		1sheet	JPY: 29,000	USD: 181.91