64-8487-64 Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3110-550
기능
- Z cut can be made in the work of the muk, and the process of making the lower hole can be shortened.
- The use of a 45° screw provides excellent chip expulsion.
- The use of 45° twist provides excellent chip discharge.
- Due to the special blade type for aluminum, burrs are greatly suppressed.
- The use of a small flat land greatly reduces tip chipping.
- Compatible Work Material: Aluminum Alloy, Copper, Resin
사양
- Blade length (mm): 22
- Total length (mm): 110
- Shank diameter (mm): 12
- Outer diameter (mm): 11
- Number of blades: 3
- Surface treatment: DLC
- Surface treatment: DLC
- Material/Finish:
- Super MG
- Note:
- Shank taper angle is a guide.
- If interference with the work is necessary, make sure to measure and check.
- Be careful of contact between the shank and the work piece.
- Country of origin: Japan
- Securities Code: 149 -3761
| 주문 번호 | 64-8487-64 | |
|---|---|---|
| 모델 번호 | DLC-AZS3110-550 | |
| JAN 코드 | 4560295102002 | |
| 표준 가격 |
JPY: 18,306
USD: 114.75
Excange rate 1USD= 159.53JPY
Valid price in Japan |
|
| 수량 | 1piece | |
| 일본의 주식 |
|
|
| 공급자 재고 |
|
|
다양한 상품군(多樣한) (다른 사이즈,다른 사양,옵션등)
| 제품 이미지 | 주문 번호 | 이름 | 모델 번호 | 수량 | 표준 가격 | 일본에서의 유효 가격 | 재고 [공급자 재고] |
|
|---|---|---|---|---|---|---|---|---|
 |
64-8487-59 | Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3070-210 | DLC-AZS3070-210 | 1piece | JPY: 9,425 | USD: 59.08 |
|
|
 |
64-8487-60 | Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3070-350 | DLC-AZS3070-350 | 1piece | JPY: 10,328 | USD: 64.74 |
|
|
 |
64-8487-61 | Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3090-270 | DLC-AZS3090-270 | 1piece | JPY: 11,863 | USD: 74.36 |
|
|
 |
64-8487-62 | Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3090-450 | DLC-AZS3090-450 | 1piece | JPY: 13,041 | USD: 81.75 |
|
|
 |
64-8487-63 | Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3110-330 | DLC-AZS3110-330 | 1piece | JPY: 16,656 | USD: 104.41 |
|
|
 |
64-8487-64 | Three-Flute High-Efficiency Long Neck Square End Mill, for DLC Coated Aluminum DLC-AZS3110-550 | DLC-AZS3110-550 | 1piece | JPY: 18,306 | USD: 114.75 |
|