MikroElektronika

MikroElektronika MIKROE-1903, Ambient 2 Click Light Sensor mikroBus Click Board for OPT3001　MIKROE-1903

Click board comes with the header strips soldered. Ambient 2 click mikroBUS™. A Click accessory module for use with MikroElektronika mikroBUS™ microcontroller development boards. The Ambient 2 click module is equipped with a TI OPT3001 ambient light sensor that measures visible light from any type of source and incorporates an infrared filter. The measurement range of the module is from 0.01 lux to 83000 lux, with 23-bit output resolution. Communication with the target MCU is via the mikroBUS I2C interface, and the board requires a 3.3V power supply.

MikroElektronika

MikroElektronika, USB 12C click USB to I2C, USB to UART Development Board for MCP2221 for MikroBUS - MIKROE-1985　MIKROE-1985

Click board comes with the header strips soldered. USB I2C click mikroBUS™. USB I2C click is a mikroBUS add-on board for enabling USB connectivity where you have UART (Universal Asynchronous Receiver and Transmitter) or I²C bus interface. It features the Microchip MCP2221, USB 2.0 to I²C and/or UART Protocol Converter with GPIO. Full-speed USB 2.0 at max. 12 Mbps I²C bus up to 400 kHz clock rates UART 300 and 115200 Baud rates General Purpose Input/Outputs (GPIO) on the edges of the board I²C bus signal and power pins are also on the other edges of the board 3.3 V (default) or 5 V power supply on mikroBUS socket Dimensions 42.9 x 25.4 mm

MikroElektronika

MikroElektronika MIKROE-2101, SHT Click Temperature & Humidity Sensor mikroBus Click Board for SHT3x-DIS　MIKROE-2101

Click board comes with the header strips soldered. SHT click mikroBUS™. SHT click is a mikroBUS™ add-on board for Temperature and Humidity sensing with digital output. It features the Sensiron SHT3x-DIS, a Humidity and Temperature Sensor. The SHT3x-DIS has increased intelligence, reliability, long-term stability and high accuracy. Alerts are programmable for certain temperature or humidity value settings with connection to the interrupt pin. Reset (RST) pin is used to generate a reset of the sensor. The interrupts allow the sensor to function as a thermostat. Fully calibrated, linearized, and temperature compensated ±2% RH typical Humidity Accuracy ±0.3°C typical Temperature Accuracy 16-Bit Humidity and Temperature Output Data I²C bus interface on mikroBUS socket I²C bus binary address hardware jumper 3.3 V (default) or 5 V power supply on mikroBUS socket Dimensions 28.6 x 25.4 mm

MikroElektronika

MikroElektronika MIKROE-2458, ECG Click Bundle Heart Rate Sensor mikroBus Click Board　MIKROE-2458

The ECG Click Board is available as a separate item, MikroElektronika part MIKROE-2455. The target board requires an MCU with a minimum 10-bit ADC. Click board comes with the header strips soldered. ECG click mikroBUS™ Bundle. The MikroElektronika ECG Click Board is an accessory board that provides a simple method of adding electrocardiogram measurement hardware to a development platform. This starter kit variant provides the required electrodes and cables in addition to the ECG Click Board. Like all Click Boards the ECG Click fits the popular mikroBUS™ socket, creating a plug-in solution to add functionality, removing the need for hardware configuration. The ECG Click measures electrical activity of the heart through 3 electrodes taped to the skin that connect to the board via a 3.5mm jack. The circuity of the ECG click amplifies the electrical signals from the heart and filters out noise, providing a clean and clear signal for the mother development board. The MikroElektronika MikroPlot software, a free to download data visualisation tool, can be used to analyse the data generated and create an ECG plot. Features. Fits the popular mikroBUS™ socket 7-block design (protection, preamplifier, high-pass filter #1, amplifier, high-pass filter #2, low-pass filter, DRL circuit) Jumpers for setting output voltage range Trimmer potentiometer to adjust gain MCP609 Op Amp MAX6106 Voltage Reference IC ESD, Overvoltage and Overcurrent protection Analogue output (mikroBUS™ AN pin) 5 V power supply. Package Contents. 1 x ECG Click Board 1 x 3 Lead ECG Cable with 3.5mm Jack 30 x Single Use ECG Electrodes

MikroElektronika

MikroElektronika MIKROE-2539, Grid-EYE Click Infrared (IR) Sensor mikroBus Click Board for AMG8853　MIKROE-2539

Click board comes with the header strips soldered. Grid-EYE click mikroBUS™. The Click accessory modules plug into the mikroBUS sockets in MikroElektronika microcontroller development boards. Grid-EYE click is an 8 x 8 thermal array sensor-detector featuring the Panasonic AMG8853 array sensor. This board detects long-wavelength infrared radiation - heat rather than light. AMG8853 thermal-infrared array sensor. Temperature measuring range: -20 to +100°C. Detecting distance: 5m. Viewing angle: 60°. Frame rate: 1 or 10fps. Communication: serial I²C bus. Power supply: +3.3 or +5Vdc. LED power indicator

MikroElektronika

MikroElektronika MIKROE-2510, Heart-Rate 4 Click Heart Rate Sensor mikroBus Click Board for MAX30101 for Wearable　MIKROE-2510

Heart Rate 4 click mikroBUS™. A Click accessory module for use with MikroElektronika mikroBUS microcontroller development boards. The Heart Rate 4 click utilises the Maxim MAX30101 high-sensitivity pulse oximeter and heart-rate sensor which includes internal LEDs, photodetectors, optical elements and low-noise electronics. The Click board communicates with the target MCU over I2C interface and requires a 3.3 or 5V power supply.

MikroElektronika

MikroElektronika MIKROE-2554, Fever Click Temperature Sensor mikroBus Click Board for MAX30205 for Wearable Devices　MIKROE-2554

Fever Click mikroBUS™. A Click accessory module for use with MikroElektronika mikroBUS microcontroller development boards. The Fever click board uses a Maxim MAX30205 human body temperature sensor and has a temperature measurement accuracy of ±0.1°C from 37 to 39°C. The click is designed to operate from a 3.3V power supply and communicates with the target MCU via I2C interface. Body temperature measurement accuracy of 0.1°C 1/256 °C temperature measurement resolution Operating temperature range 0 to 50°C

MikroElektronika

MikroElektronika MIKROE-2561, Earthquake Click Vibration Sensor mikroBus Click Board for D7S　MIKROE-2561

Earthquake click mikroBUS™. A Click accessory module for use with MikroElektronika mikroBUS microcontroller development boards. The Earthquake click utilises the DS7 high-precision seismic sensor from Omron to provide a spectral intensity (SI) acceleration value. The SI value has a high correlation with the seismic intensity scale that defines the magnitude of an earthquake. The click board communicates with the target MCU via I2C interface and requires a 3.3V or 5V power supply. Click board with Omron DS7 high-precision seismic sensor Acceleration detection range ±2,000 gal Shutoff output for seismic intensity level 5 or higher

MikroElektronika

MikroElektronika Brushless 3 Click I2C Development Board MIKROE-2766　MIKROE-2766

MikroElektronika

MikroElektronika RS485 2 Click RS-485 Add On Board MIKROE-2700　MIKROE-2700

MikroElektronika

MikroElektronika Ready for PIC MCU Development Board MIKROE-766　MIKROE-766

User guide, schematic, documentation DVD, USB cable. Ready for PIC Development Board. Ready for PIC is a development board for 40-pin DIP package Microchip PIC microcontrollers. A PIC18F device is supplied as standard. PIC18F45K22 64MHz 8-bit microcontroller, 32KB Flash memory, 1536B RAM, in DIP socket 8MHz crystal oscillator USB-UART connection via FTDI chip RESET button POWER LED GPIO port headers for Ports A/E, B, C & D mikroProg programming header Prototyping area 3.3V and 5V voltage regulators Power supply: 7-23Vac or 9-32Vdc via screw or barrel connector, 5V via USB connector Board dimensions: 141 x 84mm Pre-programmed with mikroBootloader

MikroElektronika

MIKROPROG FOR STM32,MIKROE-1100　MIKROE-1100

mikroProg for STM32 mikroProg is a high-speed USB programmer for microcontrollers with support for the mikroICD hardware in-circuit debugger.
STM32 ARM Cortex-M3 and Cortex-M4 microcontroller devices support DATA transfer display LED ACTIVE display LED LINK display LED POWER display LED

MikroElektronika

MikroElektronika SD Card Shield mikroBus Click Board - MIKROE-924　MIKROE-924

Click board comes with the header strips soldered. microSD click mikroBUS™. The Click accessory modules plug into the MikroBUS sockets in MikroElektronika microcontroller development boards. microSD Click features a microSD card slot for microSD cards used as a mass storage media for portable devices. SPI serial interface Power supply: 3.3V Ferrite voltage supply filter

MikroElektronika

MIKROE-511, 10 piece Breadboard Jumper Wire Kit　MIKROE-511

MikroElektronika Jumper Wires. Prototyping is made super easy with this range of jumper wires from MicroElektronika. This pack contains 10 jumper wires in an assortment of colours. Jumper wires, often just referred to as jumpers, are wires used on breadboards to create electronic circuits. They feature connectors at each end which easily attach to the breadboard, connector or equipment, without the need for soldering. Connections are therefore easy to change and move about the breadboard, which is essential during your prototyping phase. Each wire measures 15cm long and each pack contains 10 different coloured wires to make it really easy to identify them. There are 3 different packs available with different connector options, please refer to the information below for details.. Pack of 10 Assortment of colours 15cm long (each wire) Perfect for prototyping and education. Versions Available: ; 791-6450 791-6450 - MIKROE-511 Female to Female ; 791-6454 791-6454 - MIKROE-512 Male to Female ; 791-6463 791-6463 - MIKROE-513 Male to Male Colours included: Black Blue Green Grey Orange Pink Purple Red Yellow White

MikroElektronika

MIKROE-512, 10 piece Breadboard Jumper Wire Kit　MIKROE-512

MikroElektronika Jumper Wires. Prototyping is made super easy with this range of jumper wires from MicroElektronika. This pack contains 10 jumper wires in an assortment of colours. Jumper wires, often just referred to as jumpers, are wires used on breadboards to create electronic circuits. They feature connectors at each end which easily attach to the breadboard, connector or equipment, without the need for soldering. Connections are therefore easy to change and move about the breadboard, which is essential during your prototyping phase. Each wire measures 15cm long and each pack contains 10 different coloured wires to make it really easy to identify them. There are 3 different packs available with different connector options, please refer to the information below for details.. Pack of 10 Assortment of colours 15cm long (each wire) Perfect for prototyping and education. Versions Available: ; 791-6450 791-6450 - MIKROE-511 Female to Female ; 791-6454 791-6454 - MIKROE-512 Male to Female ; 791-6463 791-6463 - MIKROE-513 Male to Male Colours included: Black Blue Green Grey Orange Pink Purple Red Yellow White

MikroElektronika

MikroElektronika EasyPIC FUSION MCU Development Kit MIKROE-1207　MIKROE-1207

EasyPIC Fusion MCU Cards. MCU cards are 104-pin plug-in modules which carry supported PIC32, dsPIC33 and PIC24 microcontrollers in TQFP100 packaging.

MikroElektronika

MikroElektronika RFid click 13.56MHz RFID mikroBus Click Board for CR95HF - MIKROE-1434　MIKROE-1434

Click board comes with the header strips soldered. RFid click mikroBUS™. The Click accessory modules plug into the MikroBUS sockets in MikroElektronika microcontroller development boards. RFid click features a 13.56MHz contactless RFid transceiver and a trace antenna. CR95HF 13.56MHz contactless transceiver with trace antenna Supports ISO/IEC 14443 type A and B, ISO/IEC 15693 and ISO/IEC 18092 protocols (tags) It can detect, read and write NFC forum type 1, 2, 3 and 4 tags On-board dedicated internal frame controller and RF analogue front end (AFE) Communication: serial UART and SPI Power supply: +3.3Vdc Power indicator LED

MikroElektronika

MikroElektronika mikroBUS Bluetooth, Colour Sensing, GPS, GSM, Proximity, Thunder Detection, Wi-Fi, ZigBee Shield　MIKROE-1581

Click board comes with the header strips soldered. Arduino UNO click shield mikroBUS™. The MIKROE-1581 from MikroElektronika is an Arduino UNO click shield. It is an extension board which comes in a shield design, so it sits directly on top of your Arduino board. The MIKROE-158 provides you with access to an ecosystem of over 75 different click boards, each offering different functionality. Therefore opening up the possibilities of the Arduino UNO board. How does it connect to click boards? The Arduino UNO click shield houses two mikroBUS host sockets which provide easy connection to the click board range from MikroElektronika. Is it just the Arduino UNO that it works with? No, the MIKROE-158 can be used with any Arduino-compatible board. What ‘s on-board? 2 x mikroBUS host sockets Single headers: 1x10 and 1x6 Arduino connector Power supply: 3.3V or 5V What are click boards? Click boards are a range of modules from MikroElektronika which feature all sorts of technology. They provide straight-forward way of adding functionality to your microcontroller board. Categories include: Sensors Wireless Connectivity (i.e. WiFi, Zigbee and Bluetooth) Displays Human Machine Interface Motor Control Audio Power Management

MikroElektronika

MikroElektronika 4-20mA R Click MCU Add On Board MIKROE-1387　MIKROE-1387

Click board comes with the header strips soldered. 4-20 mA R click mikroBUS™. The 4-20 mA R click is an add-on board that works together with the 4-20 mA T click board ( ; 8828929 8828929 ) to create a complete 4-20 mA current loop standard - great for industrial process control and test system designs. When plugged into a microcontroller board, the R click board works as a receiver that receives an output current from a transmitter. This is converted into a voltage using the AD converter. The voltage is then converted into a 12-bit digital signal that is sent through the SPI interface. Key Features mikroBUS™ pinout standard INA196 current shunt monitor MCP3201 12-bit ADC TPS61041 DC/DC boost converter Suitable for 3.3 V or 5 V power supply

MikroElektronika

MikroElektronika MIKROE-1649, OLED W click OLED Display Add On Board With SSD1306　MIKROE-1649

Click board comes with the header strips soldered. OLED W click mikroBUS™. The OLED W click is an add-on board that allows you to add a white monochrome OLED display to your design. Key Features of the OLED W click mikroBUS™ pinout standard White monochrome passive matrix OLED display SSD1306 IC with functionality such as contrast control, normal or inverse image display and vertical/horizontal scrolling Wide viewing angle Energy saving Suitable for 3.3 V power supply 19.3 x 7.8 mm 96 x 39 px resolution

MikroElektronika

MikroElektronika MAX232 RS232 Driver Adapter Board MIKROE-222　MIKROE-222

Click board comes with the header strips soldered. MAX232 Adapter Board for RS232. The MikroElektronika MIKROE-222 is a MAX232 adapter module for serial UART communications. It is an add-on board which connects a microcontroller to RS232 devices, for example, a serial port on a PC. The MIKROE-222 features RS232 communication and can connect the MAX232 circuit device to a prototyping board. What is a MAX232? There is a MAX232 IC on this board. The MAX232 is a dual transmitter / receiver IC that converts RX, TX, CTS, RTS signals. It takes signals via the UART serial connector and converts them into signals that are RS232 standard and then sends that data to the RS232 device. What's on-board? MAX232 IC Female DB9 Connector (RS232) 6-pin connector connects with microcontroller pins for UART communication

MikroElektronika

MikroElektronika MikroElektronika MAX3232 RS232 Driver Adapter Board MIKROE-602　MIKROE-602

Click board comes with the header strips soldered. MAX3232 Adapter Board for RS232. The MAX3232 Adapter Board is ideal if you are looking to add RS232 communication to your design and require the flexibility to be able to use the board with a variety of microcontrollers. Features ; Benefits of the MAX3232 Adapter Board 3 V to 5 V operating range 250 kbps baud rates 6 prototyping connection pads to connect to other devices Energy saving

MikroElektronika

MikroElektronika, CAN Bus mikroBus Click Board for SN65HVD230 - MIKROE-986　MIKROE-986

Click board comes with the header strips soldered. CAN SPI click mikroBUS™. The CAN SPI click add-on board is great for adding CAN connectivity to your industrial and home automation designs. Features ; Benefits of the CAN SPI click mikroBUS™ pinout standard SN65HVD230 CAN transceiver Suitable for 3.3 V power supply Can withstand harsh environments

MikroElektronika

MikroElektronika MIKROE-1978, Temperature Sensor mikroBus Click Board　MIKROE-1978

Click board comes with the header strips soldered. Weather click mikroBUS™. The Click accessory modules plug into the MikroBUS sockets in MikroElektronika microcontroller development boards. The Weather click add-on board features the Bosch BME280 sensor providing accurate measurement of humidity, barometric pressure and temperature. Temperature measurement range: -40 to +85°C Humidity measurement range: 0 to 100% RH Barometric pressure measurement range: 300 to 1100hPa Three operating modes: Sleep, Forced and Normal Sleep mode: no operation, all registers accessible, lowest power, selected after startup Forced mode: perform one measurement, store results and return to sleep mode Normal mode: continuous cycling of measurements and inactive periods Communication: serial I²C, SPI Serial interface selected by jumper link Two I²C addresses available, selected by jumper link Supported by all MikroElektronika compilers Power supply: +3.3Vdc Dimensions: 28.6 x 25.4 x 3.3mm Applications: Home automation, fitness monitors, weather forecasting, vertical movement detection, remote sensing for the Internet of Things (IoT)

MikroElektronika

MikroElektronika, MikroBus Click RS-485 Interface Add On Board - MIKROE-989　MIKROE-989

Click board comes with the header strips soldered. RS485 click 3.3V mikroBUS™. The Click accessory modules plug into the mikroBUS sockets in MikroElektronika microcontroller development boards. The RS485 Click 3.3 V accessory board is designed for balanced data transmission with a 3.3V power supply. It has an on-board SN65HVD12 differential line transceiver and is supported by all MikroElektronika compliers.. mikroBus™ form factor Complies with EIA standards RS485 and RS422 UART communication interface Fits standard prototyping breadboard On-board Bias and Termination resistors mikroBUS™ is specially designed pinout standard with SPI, I2C, Analogue, UART, Interrupt, PWM, Reset and power supply pins

MikroElektronika

MikroElektronika MIKROE-1297, DALI Click DALI Add On Board for mikroBUS for Optocoupler　MIKROE-1297

Click board comes with the header strips soldered. DALI Click mikroBUS™. DALI Click is a mikroBUS add-on board for network-based systems which controls the lighting in building automation. The Digital Addressable Lighting Interface (DALI) technology is possible to address up to 64 devices in standalone systems. DALI signals received from peripherals are linked to the interrupt pin (INT). The input capture pin (PWM) can be selected instead by changing a jumper on-board. On-board optocouplers for isolating the receive and transmit signals Push button for address assignment by the physical selection method Screw terminal for the twisted wire connection 3.3 V or 5 V power supply on mikroBUS socket Dimensions 42.9 x 25.4 mm

MikroElektronika

mikroProg for CEC Programmer/Debugger　MIKROE-2002

mikroProg for CEC. mikroProg for CEC is a fast programmer and hardware debugger. It supports the Microchip CEC1302 and CEC1702(+EFUSE) , Low Power Crypto Embedded Controller, an ARM Cortex-M4 device. Integrates numerous cryptographic algorithms and secure firmware updates Enhanced Security with CEC1302 crypto features SWD Interface Power Supply from USB connection IDC10 Compatibility. Kit Contains. Damage resistant protective box mikroProg™ for CEC USB cable Documentation

MikroElektronika

MikroElektronika MIKROE-2161 TFT LCD Colour Display, 3.5in, 320 x 240pixels　MIKROE-2161

Riverdi Colour TFT LCD Displays. A range of high quality, cost effective Riverdi colour TFT LCD displays from MikroElektronika. These portrait format displays are suitable for a wide range of industrial and consumer applications and are available in basic or capacitive touch screen versions. Most of the displays are available with a white or black protective bezel. The interface type is I2C/SPI for the 2.8, 3.5 and 4.3 inch displays, and SPI/QSPI for the 5 and 7 inch displays. A MikroElektronika Riverdi click adapter board is available to allow use of the displays with various items of MikroElektronika hardware, see RS ; 136-0795 136-0795. 2.82" Displays, 320 x 240 pixels MIKROE-2156 ( ; 139-3629 139-3629 ) – Non touchscreen MIKROE-2158 ( ; 139-3630 139-3630 ) – Capacitive Touch MIKROE-2159 ( ; 139-3631 139-3631 ) – Capacitive Touch with White Bezel MIKROE-2160 ( ; 139-3632 139-3632 ) – Capacitive Touch with Black Bezel 3.5" Displays, 320 x 240 pixels MIKROE-2161 ( ; 139-3633 139-3633 ) – Non touchscreen MIKROE-2163 ( ; 139-3635 139-3635 ) – Capacitive Touch 4.3" Displays, 480 x 272 pixels MIKROE-2164 ( ; 139-3636 139-3636 ) – Non touchscreen MIKROE-2166 ( ; 139-3637 139-3637 ) – Capacitive Touch MIKROE-2167 ( ; 139-3638 139-3638 ) – Capacitive Touch with White Bezel MIKROE-2168 ( ; 139-3639 139-3639 ) – Capacitive Touch with Black Bezel 5.0" Displays, 800 x 480 pixels MIKROE-2169 ( ; 139-3641 139-3641 ) – Non touchscreen MIKROE-2171 ( ; 139-3642 139-3642 ) – Capacitive Touch MIKROE-2172 ( ; 139-3643 139-3643 ) – Capacitive Touch with White Bezel MIKROE-2173 ( ; 139-3644 139-3644 ) – Capacitive Touch with Black Bezel 7.0" Displays, 800 x 480 pixels MIKROE-2174 ( ; 139-3645 139-3645 ) – Non touchscreen MIKROE-2176 ( ; 139-3646 139-3646 ) – Capacitive Touch MIKROE-2177 ( ; 139-3647 139-3647 ) – Capacitive Touch with White Bezel MIKROE-2178 ( ; 139-3648 139-3648 ) – Capacitive Touch with Black Bezel

MikroElektronika

MikroElektronika MIKROE-2164 TFT LCD Colour Display, 4.3in, 320 x 240pixels　MIKROE-2164

Riverdi Colour TFT LCD Displays. A range of high quality, cost effective Riverdi colour TFT LCD displays from MikroElektronika. These portrait format displays are suitable for a wide range of industrial and consumer applications and are available in basic or capacitive touch screen versions. Most of the displays are available with a white or black protective bezel. The interface type is I2C/SPI for the 2.8, 3.5 and 4.3 inch displays, and SPI/QSPI for the 5 and 7 inch displays. A MikroElektronika Riverdi click adapter board is available to allow use of the displays with various items of MikroElektronika hardware, see RS ; 136-0795 136-0795. 2.82" Displays, 320 x 240 pixels MIKROE-2156 ( ; 139-3629 139-3629 ) – Non touchscreen MIKROE-2158 ( ; 139-3630 139-3630 ) – Capacitive Touch MIKROE-2159 ( ; 139-3631 139-3631 ) – Capacitive Touch with White Bezel MIKROE-2160 ( ; 139-3632 139-3632 ) – Capacitive Touch with Black Bezel 3.5" Displays, 320 x 240 pixels MIKROE-2161 ( ; 139-3633 139-3633 ) – Non touchscreen MIKROE-2163 ( ; 139-3635 139-3635 ) – Capacitive Touch 4.3" Displays, 480 x 272 pixels MIKROE-2164 ( ; 139-3636 139-3636 ) – Non touchscreen MIKROE-2166 ( ; 139-3637 139-3637 ) – Capacitive Touch MIKROE-2167 ( ; 139-3638 139-3638 ) – Capacitive Touch with White Bezel MIKROE-2168 ( ; 139-3639 139-3639 ) – Capacitive Touch with Black Bezel 5.0" Displays, 800 x 480 pixels MIKROE-2169 ( ; 139-3641 139-3641 ) – Non touchscreen MIKROE-2171 ( ; 139-3642 139-3642 ) – Capacitive Touch MIKROE-2172 ( ; 139-3643 139-3643 ) – Capacitive Touch with White Bezel MIKROE-2173 ( ; 139-3644 139-3644 ) – Capacitive Touch with Black Bezel 7.0" Displays, 800 x 480 pixels MIKROE-2174 ( ; 139-3645 139-3645 ) – Non touchscreen MIKROE-2176 ( ; 139-3646 139-3646 ) – Capacitive Touch MIKROE-2177 ( ; 139-3647 139-3647 ) – Capacitive Touch with White Bezel MIKROE-2178 ( ; 139-3648 139-3648 ) – Capacitive Touch with Black Bezel

MikroElektronika

MikroElektronika MIKROE-2173 TFT LCD Colour Display / Touch Screen, 5in, 800 x 480pixels　MIKROE-2173

Riverdi Colour TFT LCD Displays. A range of high quality, cost effective Riverdi colour TFT LCD displays from MikroElektronika. These portrait format displays are suitable for a wide range of industrial and consumer applications and are available in basic or capacitive touch screen versions. Most of the displays are available with a white or black protective bezel. The interface type is I2C/SPI for the 2.8, 3.5 and 4.3 inch displays, and SPI/QSPI for the 5 and 7 inch displays. A MikroElektronika Riverdi click adapter board is available to allow use of the displays with various items of MikroElektronika hardware, see RS ; 136-0795 136-0795. 2.82" Displays, 320 x 240 pixels MIKROE-2156 ( ; 139-3629 139-3629 ) – Non touchscreen MIKROE-2158 ( ; 139-3630 139-3630 ) – Capacitive Touch MIKROE-2159 ( ; 139-3631 139-3631 ) – Capacitive Touch with White Bezel MIKROE-2160 ( ; 139-3632 139-3632 ) – Capacitive Touch with Black Bezel 3.5" Displays, 320 x 240 pixels MIKROE-2161 ( ; 139-3633 139-3633 ) – Non touchscreen MIKROE-2163 ( ; 139-3635 139-3635 ) – Capacitive Touch 4.3" Displays, 480 x 272 pixels MIKROE-2164 ( ; 139-3636 139-3636 ) – Non touchscreen MIKROE-2166 ( ; 139-3637 139-3637 ) – Capacitive Touch MIKROE-2167 ( ; 139-3638 139-3638 ) – Capacitive Touch with White Bezel MIKROE-2168 ( ; 139-3639 139-3639 ) – Capacitive Touch with Black Bezel 5.0" Displays, 800 x 480 pixels MIKROE-2169 ( ; 139-3641 139-3641 ) – Non touchscreen MIKROE-2171 ( ; 139-3642 139-3642 ) – Capacitive Touch MIKROE-2172 ( ; 139-3643 139-3643 ) – Capacitive Touch with White Bezel MIKROE-2173 ( ; 139-3644 139-3644 ) – Capacitive Touch with Black Bezel 7.0" Displays, 800 x 480 pixels MIKROE-2174 ( ; 139-3645 139-3645 ) – Non touchscreen MIKROE-2176 ( ; 139-3646 139-3646 ) – Capacitive Touch MIKROE-2177 ( ; 139-3647 139-3647 ) – Capacitive Touch with White Bezel MIKROE-2178 ( ; 139-3648 139-3648 ) – Capacitive Touch with Black Bezel

MikroElektronika

MikroElektronika MIKROE-2174 TFT LCD Colour Display / Touch Screen, 7in, 800 x 480pixels　MIKROE-2174

Riverdi Colour TFT LCD Displays. A range of high quality, cost effective Riverdi colour TFT LCD displays from MikroElektronika. These portrait format displays are suitable for a wide range of industrial and consumer applications and are available in basic or capacitive touch screen versions. Most of the displays are available with a white or black protective bezel. The interface type is I2C/SPI for the 2.8, 3.5 and 4.3 inch displays, and SPI/QSPI for the 5 and 7 inch displays. A MikroElektronika Riverdi click adapter board is available to allow use of the displays with various items of MikroElektronika hardware, see RS ; 136-0795 136-0795. 2.82" Displays, 320 x 240 pixels MIKROE-2156 ( ; 139-3629 139-3629 ) – Non touchscreen MIKROE-2158 ( ; 139-3630 139-3630 ) – Capacitive Touch MIKROE-2159 ( ; 139-3631 139-3631 ) – Capacitive Touch with White Bezel MIKROE-2160 ( ; 139-3632 139-3632 ) – Capacitive Touch with Black Bezel 3.5" Displays, 320 x 240 pixels MIKROE-2161 ( ; 139-3633 139-3633 ) – Non touchscreen MIKROE-2163 ( ; 139-3635 139-3635 ) – Capacitive Touch 4.3" Displays, 480 x 272 pixels MIKROE-2164 ( ; 139-3636 139-3636 ) – Non touchscreen MIKROE-2166 ( ; 139-3637 139-3637 ) – Capacitive Touch MIKROE-2167 ( ; 139-3638 139-3638 ) – Capacitive Touch with White Bezel MIKROE-2168 ( ; 139-3639 139-3639 ) – Capacitive Touch with Black Bezel 5.0" Displays, 800 x 480 pixels MIKROE-2169 ( ; 139-3641 139-3641 ) – Non touchscreen MIKROE-2171 ( ; 139-3642 139-3642 ) – Capacitive Touch MIKROE-2172 ( ; 139-3643 139-3643 ) – Capacitive Touch with White Bezel MIKROE-2173 ( ; 139-3644 139-3644 ) – Capacitive Touch with Black Bezel 7.0" Displays, 800 x 480 pixels MIKROE-2174 ( ; 139-3645 139-3645 ) – Non touchscreen MIKROE-2176 ( ; 139-3646 139-3646 ) – Capacitive Touch MIKROE-2177 ( ; 139-3647 139-3647 ) – Capacitive Touch with White Bezel MIKROE-2178 ( ; 139-3648 139-3648 ) – Capacitive Touch with Black Bezel

MikroElektronika

MikroElektronika MIKROE-2176 TFT LCD Colour Display / Touch Screen, 7in, 800 x 480pixels　MIKROE-2176

Riverdi Colour TFT LCD Displays. A range of high quality, cost effective Riverdi colour TFT LCD displays from MikroElektronika. These portrait format displays are suitable for a wide range of industrial and consumer applications and are available in basic or capacitive touch screen versions. Most of the displays are available with a white or black protective bezel. The interface type is I2C/SPI for the 2.8, 3.5 and 4.3 inch displays, and SPI/QSPI for the 5 and 7 inch displays. A MikroElektronika Riverdi click adapter board is available to allow use of the displays with various items of MikroElektronika hardware, see RS ; 136-0795 136-0795. 2.82" Displays, 320 x 240 pixels MIKROE-2156 ( ; 139-3629 139-3629 ) – Non touchscreen MIKROE-2158 ( ; 139-3630 139-3630 ) – Capacitive Touch MIKROE-2159 ( ; 139-3631 139-3631 ) – Capacitive Touch with White Bezel MIKROE-2160 ( ; 139-3632 139-3632 ) – Capacitive Touch with Black Bezel 3.5" Displays, 320 x 240 pixels MIKROE-2161 ( ; 139-3633 139-3633 ) – Non touchscreen MIKROE-2163 ( ; 139-3635 139-3635 ) – Capacitive Touch 4.3" Displays, 480 x 272 pixels MIKROE-2164 ( ; 139-3636 139-3636 ) – Non touchscreen MIKROE-2166 ( ; 139-3637 139-3637 ) – Capacitive Touch MIKROE-2167 ( ; 139-3638 139-3638 ) – Capacitive Touch with White Bezel MIKROE-2168 ( ; 139-3639 139-3639 ) – Capacitive Touch with Black Bezel 5.0" Displays, 800 x 480 pixels MIKROE-2169 ( ; 139-3641 139-3641 ) – Non touchscreen MIKROE-2171 ( ; 139-3642 139-3642 ) – Capacitive Touch MIKROE-2172 ( ; 139-3643 139-3643 ) – Capacitive Touch with White Bezel MIKROE-2173 ( ; 139-3644 139-3644 ) – Capacitive Touch with Black Bezel 7.0" Displays, 800 x 480 pixels MIKROE-2174 ( ; 139-3645 139-3645 ) – Non touchscreen MIKROE-2176 ( ; 139-3646 139-3646 ) – Capacitive Touch MIKROE-2177 ( ; 139-3647 139-3647 ) – Capacitive Touch with White Bezel MIKROE-2178 ( ; 139-3648 139-3648 ) – Capacitive Touch with Black Bezel

MikroElektronika

8x8 Blue Click Shield　MIKROE-1307

Click board comes with the header strips soldered. 8x8 B LED click mikroBUS™. The Click accessory modules plug into the MikroBUS sockets in MikroElektronika microcontroller development boards.The 8x8 B Click features an 8 x 8 blue LED matrix with a serial interface. MAX7219 common-cathode display driver with serial I/O interface Analogue and digital brightness control Communication: serial SPI Power supply: +3.3V or +5Vdc

MikroElektronika

MikroElektronika solar panel　MIKROE-651

Solar Cells
Mikro Elektronika's solar cells can be used as a power source for devices by generating electricity in direct sunlight.　Main features of MIKROE-651 solar cells Panels consist of single crystal silicon solar cells sealed with PC film laminationMaximum voltage: 4.0 VMaximum current: 100 mAMaximum power: 0.4 W 70 x 65 x 3.2 mm

MikroElektronika

mikroBus Click add-on 8x8 Green LED　MIKROE-1306

Click board comes with the header strips soldered. 8x8 G click mikroBUS™. The Click accessory modules plug into the mikroBUS sockets in MikroElektronika microcontroller development boards. The add-on board features MAX7219 8-digit LED display driver module and 64 Green LED diodes. The 8 x 8 G Click™ has a 5 V power supply and communicates to the MCU via the SPI Interface.. 8 x 8 G Click is an add-on board in mikroBUS™ form factor Serial 8 x 8 GREEN LED display matrix Analogue and digital brightness control On-chip BCD code-B decoder 5 V power supply can be used with 3.3 V Microcontrollers Supported in all MikroElektronika compilers mikroBUS™ is specially designed pinout standard with SPI, I2C, Analogue, UART, Interrupt, PWM, Reset and power supply pins

MikroElektronika

mikroBus Click add-on 2-digit 7-seg LED　MIKROE-1201

Click board comes with the header strips soldered. 7seg click mikroBUS™. The Click accessory modules plug into the mikroBUS sockets in MikroElektronika microcontroller development boards. The 7seg click is easy to use and lets you add a two digit seven segment display to your device. It features two 74HC595 shift register ICs, green power LED and SMD jumper.. mikroBUS™ form factor Two 7 segment digits on-board 7seg Click connects with target board via SPI interface SMD Jumper: Operates on 3.3 V or 5 V power supply 2 x 74HC595 serial-in parallel-out shift registers with SPI interface Supported in all MikroElektronika compilers. mikroBUS™ is a specially designed pinout standard with SPI, I2C, Analogue, UART, Interrupt, PWM, Reset and power supply pins

MikroElektronika

mikroBus Click add-on 8x8 Red LED　MIKROE-1295

Click board comes with the header strips soldered. 8x8 R click mikroBUS™. The Click accessory modules plug into the mikroBUS sockets in MikroElektronika microcontroller development boards. The add-on board features MAX7219 8-digit LED display driver module and 64 Red LED diodes. The 8 x 8 G Click™ has a 5 V power supply and communicates to the MCU via the SPI Interface.. 8 x 8 R Click is an add-on board in mikroBUS™ form factor Serial 8 x 8 Red LED display matrix Analogue and digital brightness control On-chip BCD code-B decoder 5 V power supply can be used with 3.3 V Microcontrollers Supported in all MikroElektronika compilers mikroBUS™ is specially designed pinout standard with SPI, I2C, Analogue, UART, Interrupt, PWM, Reset and power supply pins

MikroElektronika

mikroBus Click add-on 8x8 Yellow LED　MIKROE-1294

Click board comes with the header strips soldered. 8x8 Y click mikroBUS™. The Click accessory modules plug into the mikroBUS sockets in MikroElektronika microcontroller development boards. The add-on board features MAX7219 8-digit LED display driver module and 64 Yellow LED diodes. The 8 x 8 G Click™ has a 5 V power supply and communicates to the MCU via the SPI Interface. 8 x 8 Y Click is an add-on board in mikroBUS™ form factor Serial 8 x 8 Yellow LED display matrix Analogue and digital brightness control On-chip BCD code-B decoder 5 V power supply can be used with 3.3 V Microcontrollers Supported in all MikroElektronika compilers mikroBUS™ is specially designed pinout standard with SPI, I2C, Analogue, UART, Interrupt, PWM, Reset and power supply pins

MikroElektronika

MikroProg programmer for PSoC 5LP　MIKROE-1449

MikroElektronika

MikroProg programmer for Kinetis MCU　MIKROE-2331