[Pico Technology]Oscilloscopes & Accessories
Filters
-
Pico Technology TA050 Attenuator, For Use With 1 GHz Signals TA050
TA050 attenuators must be used with a matched 50Ω source and load. If users wish to attenuate a signal before feeding it into a high-impedance measuring instrument, they must add a 50Ω feedthrough terminator such as Pico TA051 ( < 898-6791') 898-6791/ ). Pico Attenuator Set TA050 BNC 50Ω 1W 1GHz, 3, 6, 10, 20 dB. The Pico TA050 attenuator set consists of 4 coaxial attenuators designed for use with signals up to 1GHz. Each attenuator has a male and a female BNC connector.. Bandwidth DC to 1GHz Attenuation 3, 6, 10, 20 dB Maximum power dissipation 1W Input impedance 50Ω Output impedance 50Ω VSWR 1.5:1 or better Dimensions 56 x 20 x 17 mm Connectors BNC, 1 male + 1 female Shielded inner box with plastic shell Weight 24g each
1 products found
JPY: 16,400
USD: 102.04
-
Pico Technology PR121 Thermocouple Terminal Board PR121
Pico USB TC-08 Single Channel Terminal Board PR121. This Pico single-channel terminal board plugs into a channel on the Pico TC-08 data logger ( < 492-5105') 492-5105/ ) and turns it into a 20-bit high resolution data logger. Screw terminals enable wires to be attached to the data logger without soldering. The four input ranges (±50mV, ±500 mV, ±5 V and 4–20 mA) allow a wide range of other sensors and signals to be measured.
1 products found
JPY: 7,770
USD: 48.35
-
Pico Technology Oscilloscope Probe, Probe Type: Passive 1.5GHz 12V 1:10 TA061
Pico 1.5GHz Low Impedance Passive Probe TA061, 10:1 with SMA. Pico TA061 is a low-impedance, low-capacitance probe designed for use with oscilloscopes that have 50Ω input impedance and SMA input connectors. Applications include digital communications and RF design. Narrow 2.5 mm diameter at the probe tip New IC contact system for 0.5 to 1.27 mm pitch Interchangeable spring contact tip Ideal for measurements of SMT components Coaxial design Input resistance 500Ω Input capacitance 2pF Input coupling of the measuring instrument 50Ω System bandwidth (–3dB) 1.5GHz Rise time (10% – 90%) 240ps Rated voltage 12 V DC including AC pk Cable length 1.3m
1 products found
JPY: 89,600
USD: 557.49
-
Pico Technology Oscilloscope Probe, Probe Type: Passive 1.5GHz 12V 1:10 TA062
Pico 1.5GHz Low Impedance Passive Probe TA062, 10:1 with BNC. Pico TA062 is a low-impedance, low-capacitance probe designed for use with oscilloscopes that have 50Ω input impedance and a BNC input connector. Applications include digital communications and RF design. Narrow 2.5mm diameter at the probe tip New IC contact system for 0.5 to 1.27 mm pitch Interchangeable spring contact tip Ideal for measurements of SMT components Coaxial design Input resistance 500Ω Input capacitance 2pF Input coupling of the measuring instrument 50Ω System bandwidth (–3dB) 1.5GHz Rise time (10% – 90%) 240ps Rated voltage 12 V DC including AC pk Cable length 1.3m
1 products found
JPY: 106,000
USD: 659.53
-
Pico Technology PP877 Oscilloscope Adapter, For Use With Oscilloscope PP877
EN61326-1:2006. Mounting magnet, BNC to BNC cables (x3), battery (lithium primary cell) CR123(A). Pico Three Axis Accelerometer and Oscilloscope Interface PP877. Pico Technology supplies accelerometers that connect to an oscilloscope for measuring noise and vibration. The Pico PP877 is a MEMS-based three-axis accelerometer and oscilloscope interface. It is supplied with 3 short BNC to BNC cables which plug directly into any PicoScope oscilloscope with 3 or more analog channels. The PP877 is particularly recommended for use with high-resolution oscilloscopes such as the PicoScope 4000 Series, in order to take advantage of their increased sensitivity.. ± 5 g measurement range (measurable acceleration) DC to 350 Hz vibration frequency range Output BNC 0-2 V DC coupled Output scaling 99 to 122 mV/g 0 g output (all axes) 0.85 to 1.15 V BNC overvoltage protection 30 V Shock survivability (sensor head) 10,000 g Thread mounting (sensor) " x 28 UNF Temperature range (operating) sensor head -40 to +85 °C Dimensions 105 x 65 x 27 mm (sensor interface including BNCs), 12 mm x 18 mm diameter (magnet, including fitted grub screw) Weight 120 g (interface), 80 g (vibration sensor)
1 products found
JPY: 101,000
USD: 628.42
-
Pico Technology TA067 Test Probe Accessory Kit, For Use With TA133 Probes, TA150 Probes TA067
Pico 2.5 mm Oscilloscope Probe Standard Accessory Kit TA067. Pico TA067 is a standard accessory kit for 2.5 mm passive probes. The TA067 kit contains:15cm ground lead; 2.5mm insulating cap; 2.5mm PCB adapter kit; 0.5mm Solid tip CuBe; 0.5mm spring tip gold plated; 2.5mm sprung hook; BNC adapter. Compatible probes are: TA061 ( < 898-6832') 898-6832/ ) 1.5 GHz low-impedance probe with SMA; TA062 ( < 898-6836') 898-6836/ )1.5 GHz low-impedance probe with BNC; TA150 ( < 898-6826') 898-6826/ )350 MHz high-impedance probe; TA133 ( < 898-6820') 898-6820/ ) 500 MHz high-impedance probe. Pico ergonomically designed passive oscilloscope probes are suitable for use with the PicoScope range of USB oscilloscopes and all major brands of oscilloscopes.
1 products found
JPY: 12,000
USD: 74.66
-
Pico Technology TA065 Test Probe Accessory Kit, For Use With TA133 Probes, TA150 Probes TA065
Pico 2.5 mm Oscilloscope Probe Advanced Accessory Kit TA065. Pico TA065 is an advaned accessory kit for 2.5 mm passive probes. The TA065 kit contains: coding rings (set) 3x4 colours; 2.5mm ground blade;15cm ground lead; 2.5mm ground spring; 2.5mm IC cap 0.5 mm pitch, green;; 2.5mm IC cap 0.65 mm pitch, blue; 2.5mm IC cap 0.8 mm pitch, grey; 2.5mm IC cap 1.0 mm pitch, brown; 2.5mm IC cap 1.27 mm pitch, black; insulating cap; 2.5mm PCB adapter kit; self-adhesive Cu pad 2 x 2 cm (x2); 0.5mm Solid tip CuBe; 0.5mm spring tip gold plated; 2.5mm sprung hook; BNC adapter. Compatible probes are: TA061 ( < 898-6832') 898-6832/ ) 1.5 GHz low-impedance probe with SMA; TA062 ( < 898-6836') 898-6836/ )1.5 GHz low-impedance probe with BNC; TA150 ( < 898-6826') 898-6826/ )350 MHz high-impedance probe; TA133 ( < 898-6820') 898-6820/ ) 500 MHz high-impedance probe. Pico ergonomically designed passive oscilloscope probes are suitable for use with the PicoScope range of USB oscilloscopes and all major brands of oscilloscopes.
1 products found
JPY: 16,400
USD: 102.04
-
Pico Technology TA152 Oscilloscope Adapter, For Use With 2.5 mm Scope Probes TA152
Pico Probe Tip to BNC Adapter TA152. Pico TA152 is a useful adapter designed for connecting an oscilloscope probe tip directly to the BNC input of a DUT or source. This accessory is compatible with 2.5 mm scope probes: 350Hz and 500Hz high impedance (TA101, TA133, TA150); 1.5GHz low impedance (TA061 and TA062).
1 products found
JPY: 4,350
USD: 27.07
-
［Discontinued］pico Technology Hard Carrying Case, Dimensions 340 x 270 x 83mm, Height 83mm, length 340mm, For Use With PicoScope 2206 MI136
PicoScope carry case is a replacement for that supplied with the Pico oscilloscope kits. PicoScope Carry Case. Used to protect the PicoScope Oscilloscope when used in the field, and to safely store it when not needed Constructed from high-density foam to securely hold the PicoScope 2202, 3200 range and 4000 Series Space is also proved to store leads and scope probes External dimensions: 340 x 270 x 83 mm (13.4 x 10.6 x 3.3 in)
1 products found
JPY: 5,920
USD: 36.83
-
［Discontinued］Pico Technology KA044 Oscilloscope 20-Way Digital Cable, Model TA136, For Use With PicoScope 2205 MSO KA044
PicoScope 6 high-end oscilloscope kit. PicoScope 2000. The PicoScope 2000 offers excellent performance and value. It is an extremely versatile all-in-one full-function oscilloscope, spectrum analyser, signal generator and arbitrary waveform generator (AWG). It has a compact footprint of 100 x 135 mm and fits neatly into a laptop or travel bag. The small, rugged case has three BNC connectors; two dedicated input channels and a dedicated BNC for the signal generator and arbitrary waveform generator. Power is taken directly from the PC and uses the full USB 2.0 bandwidth (480 Mbps) allowing a fast screen update rate without compromising accuracy and detail. All PicoScope® PC oscilloscopes are powered by high-end PicoScope 6 Windows software, with updates, feature extensions and improvements that will remain free for the lifetime of the product. PicoScope 6 is powerful yet easy to operate. Users benefit from the power of the PC, and the familiar Windows interface and controls, making the software easy to learn and easy to use on a daily basis. Data is easily saved in a variety of formats including CSV text, PNG and BMP images and MATLAB binary files. Drivers and examples are included for LabVIEW, C/C++, Delphi and VB for integration into custom applications. Oscilloscope Mixed Kit < 749-4966') 749-4966/ is supplied with: PicoScope 2205 MSO, TA136 Digital Cable, 2 x TA139 [ack of 10 test clips, 2 x MI007 Probes, PicoScope probe pouch, Software and Reference CD, Quick Start Guied and USB Cable. PicoScope® 2000 series accessories available separately include: < 749-4957') 749-4957/ PP787 2x 60MHz MI007 probes for PicoScope 2204, 2205 & 2206, supplied in PicoScope probe pouch; < 749-4950') 749-4950/ PP821 2x 150MHz probes for PicoScope 2207; < 749-4954') 749-4954/ PP822 2x 250MHz probes for PicoScope 2208; < 749-4960') 749-4960/ TA136 20-way, 25cm digital cable; < 749-4979') 749-4979/ TA139 pack of 10 test clips.. Connected and powered via USB 2.0 (480 Mbps) Lightweight and compact size ideal for field use Compatible with LabVIEW, C/C++, Delphi and VB Operates with Windows XP and Vista
1 products found
JPY: 2,350
USD: 14.62
-
［Discontinued］pico Technology PicoScope 4000 Series 4824 Oscilloscope, PC Based, 8 Channels, 20MHz KA393
5. PicoScope 4824 High Precision PC Oscilloscope. PicoScopes are small, light, readily portable oscilloscopes powered via USB (eliminating the need for a bulky adaptor). The 4824 has 8 high-precision, low-noise inputs, a bandwidth of 20MHz and sensitivity from 2mV/div. These attributes make the 4824 well-suited to applications ranging from general purpose testing to power supply start sequencing, decode and time-aligned display of related I/O, 7-channel audio systems, 3-phase voltage ; current measurements and multi-phase motor drives. A maximum sampling rate of 80MS/s, deep buffer memory of 256MS and data streaming enable the 4824 to capture detailed timing data over prolonged periods. Features included as standard include: 20MHz FFT spectrum analyzer, segmented memory (for bursts of up to 10,000 captures in fewer than 30 milliseconds); math channels; automatic measurements; colour persistence display mode; advanced digital triggering; mask limit testing; serial decoding (SPI, l ;sup>2 ;/sup>C, l ;sup>2 ;/sup>S, RS-232/UART, CAN, LIN and FlexRay. A free SDK is included for developing applications in popular programming languages including C, Microsoft Visual Basic®, National Instruments LabView® and MathWorks MATLAB®. Suitable accessories, available separately, include passive voltage oscilloscope probe MI007 ( RS ; 800-3029 800-3029 ), 60MHz, x1/x10. 8-channel, 12-bit resolution PC oscilloscope High performance arbitrary waveform generator SuperSpeed USB 3.0 interface PicoScope 6 software displays up to 16 scope and spectrum views at once Low sine and pulse distortion Advanced digital triggers Serial bus decoding
1 products found
JPY: 267,000
USD: 1,661.27
-
［Discontinued］Pico Technology Oscilloscope Probe, Probe Type: Active, Differential 200MHz 60V 1:10 TA045
Pico 200MHz 20V Differential ProbeTA045, 10:1. Pico TA045 is a 200MHz bandwidth active differential probe suitable for high-speed measurement applications with a differential measurement range of ±20V and a common-mode range of up to ±60V (DC + peak AC). This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high-voltage differential measurements. Applications include making safe measurements in power circuit applications and acquisition of low-speed balanced differential signals found in serial communications buses. The TA045 is optimised for small-signal applications such as telecom measurement, xDSL, high-speed power measurement and differential transmitter and receiver design. Bandwidth DC to 200MHz (–3 dB) Attenuation 10:1 Rise time 1.75ns Accuracy ±1% Input impedance 500kΩ ll 7pF each side to ground Differential range ±20V Common mode range ±60V Absolute maximum voltage (either input to ground) ±60V Swing (into 50 Ω load) ±2V Offset (typical) <±2mV Noise (typical) 0.3mVRMS Source impedance (typical) 50Ω CMRR (typical) 80dB @ 100Hz; 50dB @ 10MHz Ambient operating temperature -10 to +40°C Ambient storage temperature -30 to +70°C Power requirement 4xAA cells or 6VDC/90mA mains adaptor or 9VDC/70mA mains adaptor Length of input leads 50cm Length of BNC lead 125cm Weight 300g Dimensions 111 x 22 x 14 mm
1 products found
JPY: 143,000
USD: 889.75
-
［Discontinued］Pico Technology Oscilloscope Probe, Probe Type: Active, Differential 800MHz 30V 1:10 TA046
Pico 800MHz 15V Differential Probe TA046,10:1. Pico TA046 is a high-bandwidth differential probe. With a fast 800MHz bandwidth it is ideal for measuring high-speed differential signals. This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high-voltage differential measurements. Applications include making safe measurements in power circuit applications and acquisition of low-speed balanced differential signals found in serial communications buses. Capabilities cover wireless and data communication, disk drive design, communication pulse shape compliance and troubleshooting ground bounce problems. Bandwidth DC to 800MHz (twin pin configuration) Accuracy ±2% Input impedance 100 kΩ ll 2pF Attenuation 10:1 Input voltage maximum differential ±15V Input voltage common mode ±30V Input voltage absolute maximum ±40V Swing (into 50Ω load) ±1.5V Offset (typical) <±5mV Noise (typical) 0.3mVRMS Output impedance(typical) 50Ω CMRR (typical) 60dB @ 60Hz; 15dB @ 500MHz Output BNC cable length 1.2m Power requirement 15 VDC/100mA regulated mains adaptor Ambient operating temperature -10 to +40°C Ambient storage temperature -30 to +70°C Weight 130g Dimensions 111 x 22 x 14 mm
1 products found
JPY: 162,000
USD: 1,007.96
-
［Discontinued］Pico Technology Oscilloscope Probe, Probe Type: Active, Differential 25MHz 1kV 1:20, 1:200 TA057
Pico 25MHz 1400V Differential Probe TA057, 20:1/200:1. Pico TA057 is 25MHz bandwidth active differential probe suitable for high common-mode voltage measurement applications up to ±1400V (DC + peak AC). This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high-voltage differential measurements. Applications include making safe measurements in power circuit applications and acquisition of low-speed balanced differential signals found in serial communications buses. The TA057 is suitable for measuring transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays, as well as signals in the millivolt range from sensors and other instrumentation. The differential inputs make it possible to measure voltages on floating circuits. Bandwidth DC to 25MHz (–3 dB) Attenuation ratio 20:1/200:1 Accuracy ±2% Rise time 14ns Input impedance 4MΩ ll 5.5pF each side to ground Differential range (20:1) ±140V (DC + peak AC) or 140VRMS Maximum differential (200:1) ±1400V (DC + peak AC) or 1000VRMS Common mode range ±1400V (DC + peak AC) or 1000VRMS (20:1 & 200:1) Absolute maximum voltage (differential or common mode) ±1400V (DC + peak AC) or 1000VRMS CATIII (20:1 & 200:1) Maximum amplitude ±7V into 50kΩ load Offset (typical) <±5mV Noise (typical) 0.7mVRMS Source impedance (typical) 1Ω @ 1kHz, 8Ω @ 1MHz CMRR (typical) 80dB @ 50Hz; 60dB @ 20kHz Ambient operating temperature -10 to +40 °C Ambient storage temperature -30 to +70°C Power requirement 4xAA cells or 6VDC/60mA mains adaptor or regulated 9VDC/40mA mains adaptor Length of input leads 45cm Length of BNC lead 95cm Weight 400g Dimensions 170 x 63 x 21 mm
1 products found
JPY: 51,680
USD: 321.55
-
［Discontinued］Pico Technology Oscilloscope Probe, Probe Type: Active, Differential 50MHz 600V 1:10 TA058
Pico 50MHz 70V Differential Probe TA058,10:1. Pico TA058 is a 50MHz bandwidth active differential probe suitable for high common-mode voltage measurement applications up to ±700V (DC + peak AC). This differential probe extends the functionality of standard single-ended input oscilloscopes to allow a safe and accurate method of making high-voltage differential measurements. Applications include making safe measurements in power circuit applications and acquisition of low-speed balanced differential signals found in serial communications buses. The TA058 is suitable for measuring transients in switching power supplies, inverters and motor drives, electronic ballasts and CRT displays, as well as signals in the millivolt range from sensors and other instrumentation. The differential inputs make it possible to measure voltages on floating circuits. Bandwidth DC to 50MHz (–3 dB) Attenuation ratio 10:1 Accuracy ±1% Rise time <7ns Input impedance 1.6MΩ ll 7pF each side to ground Differential range ±70V (DC + peak AC) or 70VRMS Common mode range ±700V (DC + peak AC) or 600VRMS Absolute maximum voltage (either input to ground) ±700V (DC + peak AC) or 600VRMS CATI Swing ±7V into 5kΩ load Offset (typical) <±2mV Noise (typical) 0.7mVRMS Source impedance (typical) 50Ω CMRR (typical) 95dB @ 60Hz; 60dB @ 1MHz Ambient operating temperature -10 to +40 °C Ambient storage temperature -30 to +70°C Power requirement 4xAA cells or 6VDC/90mA mains adaptor or regulated 9VDC/70mA mains adaptor Length of input leads 50cm Length of BNC lead 125cm Weight 300g Dimensions 111 x 22 x 14 mm
1 products found
JPY: 65,130
USD: 405.24
-
［Discontinued］Pico Technology MI077 Current Probe MI077
Retractable hook tip, compensation adjustment tool, locating sleeves (x2), marker rings (x6), ground lead. Pico 600 A AC/DC Current Probe MI077, 4 mm (Banana) Plug Type Connector. Pico MI077 current clamp can measure AC and DC currents up to 600A. Two current ranges controlled by selector switch Low–battery indicator Zero offset button Output connectors 4 mm (banana) plug type Accuracy: DC 0 to 600A ± (2% reading +2A); AC 0 to 300A ± (2% reading +2A); AC/DC 300A to 500A ± (3% reading +2A); AC/DC 500A to 600A ± (6% reading +2A) AC frequency range 50Hz to 400Hz Voltage output 1mV per 1A (0 to 600mV AC & DC) Max conductor size 30mm Operating environment 0 to +50 °C, 70% RH Battery life 100 hours with carbon zinc Battery type 9 V DC NEDA 1604, 6F22, 006P Dimensions 178 x 70 x 33 mm
1 products found
JPY: 14,500
USD: 90.22
-
［Discontinued］Pico Technology TA019 Current Probe TA019
Pico 600 A AC/DC Current Probe TA019, BNC Connector. Pico TA019 current probe can measure AC and DC currents up to 60A.. Two current ranges controlled by selector switch Low–battery indicator Zero offset button Output connectors BNC with screened lead Screened lead for noise suppression Accuracy: DC 0 to 600 A ± (2% reading +2 A); AC 0 to 300 A ± (2% reading +2 A); AC/DC 300 A to 500 A ± (3% reading +2 A); AC/DC 500 A to 600 A ± (6% reading +2 A) AC frequency range 50Hz to 400Hz Voltage output1mV per 1A (0 to 600 mV AC & DC) Max conductor size 30 mm Operating environment 0 to +50 °C, 70% RH Battery life 100 hours with carbon zinc Battery type 9 V DC NEDA 1604, 6F22, 006P Dimensions 178 x 70 x 33 mm
1 products found
JPY: 15,300
USD: 95.20
-
［Discontinued］Pico Technology Oscilloscope Probe, Probe Type: Passive 500MHz 1:10 TA133
IEC/EN 61010-031. Coding rings (set) 3x4 colours; ground blade 2.5mm; ground lead 15cm; ground spring 2.5mm; IC-Cap 2.5, 0.5mm pitch, green; IC-Cap 2.5, 0.65mm pitch, blue; IC Cap 2.5, 0.8mm pitch, grey; IC Cap 2.5, 1.0mm pitch, brown; IC Cap 2.5, 1.27mm pitch, black; insulating cap; self-adhesive Cu pad 2 x 2 cm (x2); Solid tip CuBe 0.5mm; spring tip gold plated 0.5mm; sprung hook; trim tool; PCB adaptor kit. Pico 500MHz High Impedance Passive Probe TA133, 10:1 with BNC. Pico TA133 is a high-impedance passive probe with 500MHz bandwidth. It is designed for use with oscilloscopes with a 1MΩ input impedance and has a fixed attenuation of 10:1. The TA133 has been compensated to ensure optimal performance with the PicoScope 6404 oscilloscopes. The compact design of this high-performance probe means there is only 2.5mm housing diameter at the probe tip compared to the conventional 5mm housing, making it easier to see the device under test and making it ideal for measurements of SMT components. Resistance at probe tip 10MΩ Capacitance at probe tip 9.5pF Scope input impedance 1MΩ Bandwidth (3dB) DC to 500MHz Maximum working voltage 300 V RMS CAT II Rise time (10% to 90%) 700ps Compensation range 10 to 25 pF Compatible with PicoScope 6404A/B/C/D Cable length 1.3m
1 products found
JPY: 47,800
USD: 297.41
-
［Discontinued］Pico Technology Oscilloscope Probe, Probe Type: Passive 350MHz 1:10 TA150
Coding rings (set) 3x4 colours; ground blade; ground lead 15cm; ground spring; insulating cap; sprung hook; trim tool. Pico 350MHz High Impedance Passive Probe TA150, 10:1 with BNC. Pico TA150 is a high-impedance passive probe with 350MHz bandwidth. It is designed for use with oscilloscopes with a 1MΩ input impedance and has a fixed attenuation of 10:1. The TA150 has been compensated to ensure optimal performance with the PicoScope 6402 and 6403 oscilloscopes. The compact design of this high-performance probe means there is only 2.5mm housing diameter at the probe tip compared to the conventional 5mm housing, making it easier to see the device under test and making it ideal for measurements of SMT components. Resistance at probe tip 10MΩ Capacitance at probe tip 9.5pF Scope input impedance 1MΩ Bandwidth (3dB) DC to 350MHz Maximum working voltage 300 V RMS CAT II Rise time (10% to 90%) 1ns Compensation range 10 to 25 pF Compatible with PicoScope PicoScope 6402A/B/C/D, 6403A/B/C/D Cable length 1.3m
1 products found
JPY: 26,590
USD: 165.44
-
［Discontinued］Pico Technology TA066 Test Probe Accessory Kit, For Use With TA133 Probes, TA150 Probes TA066
Pico 2.5 mm Oscilloscope Probe Basic Accessory Kit TA066. Pico TA066 is a basic accessory kit for 2.5 mm passive probes. The TA066 kit contains:15cm ground lead; 0.5mm Solid tip CuBe; 0.5mm spring tip gold plated; 2.5mm sprung hook. Compatible probes are: TA061 ( < 898-6832') 898-6832/ ) 1.5 GHz low-impedance probe with SMA; TA062 ( < 898-6836') 898-6836/ )1.5 GHz low-impedance probe with BNC; TA150 ( < 898-6826') 898-6826/ )350 MHz high-impedance probe; TA133 ( < 898-6820') 898-6820/ ) 500 MHz high-impedance probe. Pico ergonomically designed passive oscilloscope probes are suitable for use with the PicoScope range of USB oscilloscopes and all major brands of oscilloscopes.
1 products found
JPY: 6,820
USD: 42.43
