[Pilz]Automation & Control Gear
Filters
-
Pilz P2HZ X3 24 V dc Safety Relay Dual Channel With 2 Safety Contacts 774350
PILZ P2HZ X3 Safety Relay. The PILZ P2HZ X3 range is an affordable, durable and reliable safety relay designed with two handed control units in mind. Useful when you need to control your press controllers and safety circuits. Features and benefits. Specially designed for two handed control/operation. The P2HZ series will not function unless the operator has their hands outside the danger zone area during hazardous movement. LED indicator for switching your channel status from 1 to 2 and also to monitor your supply voltage Single or Dual channel input operation (Single channel are used more beneficially with smaller type machines where you need to use a dedicated logic device that only has a small function to cut off in an emergency – Dual allows you to take control of more safety circuits and control a greater amount of control zones at any given time) Suitable for DIN rail mounting Durable and has an extended service life vs. competitors Positive guided relay outputs (2 safety contacts, 1 auxiliary). Safety features. The relay will provide the circuit self-monitoring. The safety functions of the device remain in effect even in the case of component failures. The relay will prevent the circuit from further press strokes in the case of, relay failures, contact welding, coil defects or open/short circuits. Applications. Mechanical presses Hydraulic presses General safety circuits (in accordance with EN 60204-1). Technical safety parameters. EN 60204-1 EN 954-1 EN (IEC) 62061 EN ISO 13849-1 IEC 61511 – SIL 3
1 products found
JPY: 106,000
USD: 664.45
-
Pilz PSWZ X1P 24 → 240 V ac/dc Safety Relay Single or Dual Channel With 2 Safety Contacts 777949
VDE 0113; EN 60204-1; IEC 204-1. BG, UL, CUL. PSWZX1P Safety Relay by PILZ. The PSWZX1P range of safety relays from PILZ offers you safety and performance all in one. The PSWZX1P offers you different modes of operation such as single or dual channel switches. Suitable specifically for operating your safe standstill machinery or tools that are deemed dangerous or hazardous to health. Features and benefits:. DIN rail mounted with screw terminals LED display that offers you the following measures: - Supply voltages - Standstill on Channel 1 / 2 - Switch status - Fault signal if simultaneity time is exceeded Semiconductor output signal (input for reset function): - Error - Switch status Measure inputs for single or three-phase motors Measuring voltage is selectable Feedback loop is in operation Plug in connection terminals is possible. Safety features:. Relays K1 ; K2 are interlocked specifically designed so that the unit cannot be switched back on in the case of contact welding or an open circuit (ensuring your safety at all times) The unit will monitor and measure and look out for an open circuit. If the circuit does open, the unit will immediately switch itself off to prevent hazards The standstill motor which is unique to the PSWZ X1P prevents the plant from being enabled, in the following cases: - Power supply failure - Component failure - Measuring circuits are open circuit - Coil deflect / open circuit. Applications:. B>Safe standstill monitoring – this is the units main purpose and is specifically designed for safe standstill where areas of operation such as plants have dangerous machinery or tools in use. Safe standstill monitoring is only detected on power free measuring circuits. Any residual voltages, induced voltages or drives with in the position control will prevent the relay from its main function so take this into consideration when in use. Technical safety parameters:. EN 60204-1 EN 62061 EN ISO 13849-1 EN ISO 14119 VDE 0113-1
1 products found
JPY: 155,000
USD: 971.60
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 541009
The safety level PLe (Cat. 4)/SIL CL 3 is only achieved if the safety outputs use 2-channel processing. EN 60947-5-3 with the actuator PSEN cs3.1 PDDB; EN 62061 SIL CL 3; EN ISO 13849-1 PLe Cat. 4; EN ISO 14119 coding level Low, Type4. CE, cULus Listed, TÜV, BG, CCC. Actuator. PSENcode Compact Non-Contact Safety Switch, Coded. The PSEN cs3.1 and PSEN cs3.1p safety switches are coded and only switch with an actuator from the PSEN cs3.1 series. There is no restriction on the number of times the actuator can be used and reset. Features and Benefits. Transponder technology for presence detection (safety function) Coded switch Dual-channel operation 2 safety inputs for series connection of multiple safety switches 2 safety outputs 1 signal output LED display for state of the actuator, state of the inputs and supply voltage/fault 1 direction of actuation IP69K protection Stock no. ; 918-6655 918-6655 has an M12 8 pole male connector Stock no. ; 918-6664 918-6664 has an M8 8 pole male connector
1 products found
JPY: 34,500
USD: 216.26
-
Pilz PNOZ XV2 24 V dc Safety Relay Dual Channel With 2 Safety Contacts 774502
EN 60204-1, EN 62061, EN ISO 13849-1, VDE 0113-1, EN 60947-5-1. CE, cULus Listed, TÜV, KOSHA, CCC. PNOZ XV2 Safety Relay, Adjustable Time Delayed. The PNOZ XV2 range of safety relays from PILZ offers you safety and performance of a top branded safety relay all in one. The PNOZ XV2 offers you different modes of operation such as single or dual channel switches. Suitable for several different applications which are listed below. Features and benefits:. DIN rail mounted with screw terminals 2 instantaneous delay-on re-energised safety contacts LED operating voltage displayed alongside switching psitions and also the reset circuit Connections built in for safety limit switches, e-stops and more Single or dual channel operation Simple and fast wiring saving you time, effort and money long term Save costs when exchanging units (there ‘s no need to rewire therefore you should eliminate potential wiring errors). Electromechanical, potential-free. Safety features. The circuit is redundant with built-in self-monitoring. The safety function remains effective in the case of a component failure. The correct opening and closing of the safety function relays is tested automatically in each on-off cycle. International certification Faster commissioning and simple wiring through units with plug-in terminals High plant availability and short downtimes thanks to a convenient diagnostic options on the device. Applications. E-STOP pushbuttons Safety gate limit switches Reset buttons. Technical safety parameters. EN 60947-5-1 EN 60204-1 VDE 0113-1
1 products found
JPY: 118,000
USD: 739.67
-
Pilz PNOZ 11 24 V ac/dc Safety Relay Dual Channel With 7 Safety Contacts 774080
Safety Relay for Emergency Stop Circuits and Safety Gates, PNOZ 11. Single or dual channel cabling with short-circuit detection Choice of self-monitoring or automatic reset Display LEDs for status of channels 1 and 2, input circuits, power supply voltage and reset Return loop for monitoring external contactors 2 solid state outputs
1 products found
JPY: 134,000
USD: 839.97
-
Pilz PNOZ X10 24 V dc Safety Relay Single or Dual Channel With 6 Safety Contacts 774709
PNOZ X10, Dual Channel. Introducing the PNOZ X10 range of safety relay from the well-known brand PILZ, manufacturer of many safety related monitoring products. The PNOZ X10 range is the top of its class offering you different modes of operation including, single, automatic and dual channel functions. You will find that the PNOZ X10 has many different applications that you can use that offer you versatility in the face of machine safety. Features and benefits. LED indicator statuses to support switching channel status between 1 or 2 signals ; also for monitoring the supply voltage currently in the relay Featuring 6 safety contacts (instantaneous) and 4 auxiliary contacts furthering the reliability of the machines safety output. DIN rail mounting as standard Single/Dual channel operation Detection of short circuits across the contacts which can specifically detect earth faults and short circuiting. Safety features. The circuit is redundant with built in self-monitoring Safety functions remain effective in the case of a component failure Correct opening and closing of the safety functions is tested automatically at the end of each of the relays on/off safety cycles. Your X10 is short circuit proof, using an electronic fuse on a DC supply provides this reliability. Applications. Emergency stop buttons Safety gate limit switches Reset buttons Light barriers. Technical safety parameters. EN 60947-5-1 EN 60204-1 VDE 0113-1
1 products found
JPY: 130,000
USD: 814.89
-
Pilz PZE X4 24 V dc Safety Relay Single Channel With 4 Safety Contacts 774585
BG, UL listed for Canada and US. All base units must have a feedback control loop. PZE X4 24VDC 4n/o Safety Relay from PILZ. The PILZ PZE X4 is primarily used for increasing the number of contacts you can use between your safety related control devices such as E stops, safety gates and more. The reliability Safety Relay technology from PILZ means you can control your environment with confidence that the safety status is being monitored. Features and benefits. Universal power supply, compatible with many different outlets of power sources LED indicator for switching your channel status from 1 to 2 and also to monitor your supply voltage Plug in terminal connections with either a spring loaded terminal or screw terminal giving you versatility in where your unit can be used. Feedback loop monitoring come with all base units allowing you to monitor the safety loop and identify hazards before they happen. Single or Dual channel input operation (Single channel are used more beneficially with smaller type machines where you need to use a dedicated logic device that only has a small function to cut off in an emergency – Dual allows you to take control of more safety circuits and control a greater amount of control zones at any given time). Safety features. Earth fault in the feedback loop can be detected depending on the base unit that is used Earth faults in the input circuit can be detected as the output will de-energise the relays and open the safety contacts. The device will retain its safety functions in any case of component failures ensuring your safety. Any safety functions in your existing circuit can be easily transferred with this expansion module with ease. Applications. Guard systems Emergency stop buttons Pull wire emergency stop switches Safety light curtains Safety sensors. Technical safety parameters. EN 60204-1 EN 62061 EN ISO 13849-1 VDE 0113-1
1 products found
JPY: 46,100
USD: 288.97
-
Pilz PNOZ XV1P 24 V dc Safety Relay Single or Dual Channel With 2 Safety Contacts 777602
EN954-1, IEC / EN60204-1. BG, UL listed for Canada and US. PNOZ XV1P, Adjustable Time Delayed. The PNOZ XV1P Series of Safety relays from PILZ offers you affordable, reliable and trustworthy safety relays that adhere to protecting you and your environment. The PNOZ XV1P comes with a variety of different features and functions that diversify it from some of its competitors, some of these features are listed below. Features and benefits. An adjustable time delay allows you full control over when you need the device to function, stop or start. B>Single or Dual channel input operation ( Single channel are used more beneficially with smaller type machines where you need to use a dedicated logic device that only has a small function to cut off in an emergency – Dual allows you to take control of more safety circuits and control a greater amount of control zones at any given time) B>Automatic or Manual reset ( Automatic reset is there to automatically take over when there is no reset switch linked to the feedback circuit, meaning that the device will automatically start when an input turns ON. Manual is the opposite in that when a reset switch is present it will feed into the circuit and will not start automatically, giving you further control over when you wish to run the device. B>LED status indicators giving you the ability to monitor and action any problems before they arise. B>DIN rail mounting with snap on capabilities allowing you to plug and play the safety relay where needed. Applications. Guard systems Emergency stop buttons Pull wire emergency stop switches Safety light curtains Safety sensors. Technical safety parameters. EN 60204-1 EN 62061 EN ISO 13849-1 VDE 0113-1
1 products found
JPY: 94,000
USD: 589.23
-
Pilz PNOZ XV1P 24 V dc Safety Relay Single or Dual Channel With 2 Safety Contacts 777601
EN954-1, IEC / EN60204-1. BG, UL listed for Canada and US. PNOZ XV1P, Adjustable Time Delayed. The PNOZ XV1P Series of Safety relays from PILZ offers you affordable, reliable and trustworthy safety relays that adhere to protecting you and your environment. The PNOZ XV1P comes with a variety of different features and functions that diversify it from some of its competitors, some of these features are listed below. Features and benefits. An adjustable time delay allows you full control over when you need the device to function, stop or start. B>Single or Dual channel input operation ( Single channel are used more beneficially with smaller type machines where you need to use a dedicated logic device that only has a small function to cut off in an emergency – Dual allows you to take control of more safety circuits and control a greater amount of control zones at any given time) B>Automatic or Manual reset ( Automatic reset is there to automatically take over when there is no reset switch linked to the feedback circuit, meaning that the device will automatically start when an input turns ON. Manual is the opposite in that when a reset switch is present it will feed into the circuit and will not start automatically, giving you further control over when you wish to run the device. B>LED status indicators giving you the ability to monitor and action any problems before they arise. B>DIN rail mounting with snap on capabilities allowing you to plug and play the safety relay where needed. Applications. Guard systems Emergency stop buttons Pull wire emergency stop switches Safety light curtains Safety sensors. Technical safety parameters. EN 60204-1 EN 62061 EN ISO 13849-1 VDE 0113-1
1 products found
JPY: 94,000
USD: 589.23
-
Pilz PZE X4V 24 V dc Safety Relay Single Channel With 4 Safety Contacts 774581
BG, UL listed for Canada and US. EN954-1, IEC / EN60204-1. All base units must have a feedback control loop. PZE X4VP, Expansion Module, Time Delayed. Category 4 to EN954-1 Contact expansion for use with safety relays Resets with base unit LED status indication Screw terminals DIN rail mounting
1 products found
JPY: 50,700
USD: 317.81
-
Pilz PZE X4V 24 V dc Safety Relay Single Channel With 4 Safety Contacts 774583
BG, UL listed for Canada and US. EN954-1, IEC / EN60204-1. All base units must have a feedback control loop. PZE X4VP, Expansion Module, Time Delayed. Category 4 to EN954-1 Contact expansion for use with safety relays Resets with base unit LED status indication Screw terminals DIN rail mounting
1 products found
JPY: 50,700
USD: 317.81
-
PSENmag Magnetic Safety Switch, Plastic, 24 V dc 540100
EN60947-5-3 standard is only met if entire system consisting of safety switch (PSENcode), actuator (PSENcode) and a safety monitoring module (PNOZ X or PNOZmulti) is used. EN954-1 (Cat 4), EN60204-1, EN60947-5-3. CE, cULus Listed, TÜV, FCC, IC. Actuator. When the safety gate is closed the switch provides 2 N/C semiconductor outputs. PSENcode Large Non-Contact Safety Switch, Fully Coded. The PSEN cs2.1p safety switch is fully coded and will only switch with an actuator from the PSEN cs2.1 series. The actuator must be taught and can be taught up to a maximum of 8 times but with only 1 actuator at a time. Series connection - you can connect more than 10 safety switches in sequence to Cat 4 of EN954-1 The switch reacts to a single actuator but can be taught a new actuator up to 8 times if operational damage occurs 5 directions of actuation M12 connection, 8-pin
1 products found
JPY: 56,100
USD: 351.66
-
PSENmag Magnetic Safety Switch, Plastic, 24 V dc 540200
EN60947-5-3 standard is only met if entire system consisting of safety switch (PSENcode), actuator (PSENcode) and a safety monitoring module (PNOZ X or PNOZmulti) is used. EN954-1 (Cat 4), EN60204-1, EN60947-5-3. BG, cUL, CCC. Actuator. When the safety gate is closed the switch provides 2 N/C semiconductor outputs. PSENcode Large Non-Contact Switch, Unique Coded. The PSEN cs2.2p safety switch is fully coded and the coding is unique which means it will only switch with the supplied actuator. If the actuator/switch is lost or broken, you will need to buy a new set. Series connection - you can connect more than 10 safety switches in sequence to Cat 4 of EN954-1 Unique assignment of switch and its actuator. They are coded only to each other for their operational life 5 directions of actuation M12 connection, 8-pin
1 products found
JPY: 63,800
USD: 399.93
-
PSENme Solenoid Interlock Switch Power to Unlock 24 V ac/dc 570000
VDE 0660 T100, EN 60947-1, VDE 0660 T200, EN 60947-5-1, IEC 60947-5-1 GS-ET-19. EC, BG, CCC, cCSAus. PSENmech Safety Switch. The PSENmech mechanical safety switch is suitable for the safe monitoring of a movable guard. The safety switch is triggered if the guards are opened, and the hazardous machine movement is stopped via a Pilz evaluation device. The PSENmech safety switch prevents the safety gate from being opened unintentionally by using increased extraction force on the actuator. It complies with EN 1088 standard (protection against defeat) thanks to its mechanically coded actuator. Flexibility and speed during installation plus high plant availability Compact design Up to four horizontal and four vertical approach directions Innovative connection technology Universal integration - possible to connect to all common control voltages Built-in manipulation protection Long service life Robust design and high mechanical load capacity Heavy duty positive opening safety contacts with galvanic isolation Wide operating temperature range IP67 protection Easy to service cage clamp terminals
1 products found
JPY: 48,500
USD: 304.02
-
PSENme Solenoid Interlock Switch Power to Unlock 24 V ac/dc 570001
VDE 0660 T100, EN 60947-1, VDE 0660 T200, EN 60947-5-1, IEC 60947-5-1 GS-ET-19. EC, BG, CCC, cCSAus. PSENmech Safety Switch. The PSENmech mechanical safety switch is suitable for the safe monitoring of a movable guard. The safety switch is triggered if the guards are opened, and the hazardous machine movement is stopped via a Pilz evaluation device. The PSENmech safety switch prevents the safety gate from being opened unintentionally by using increased extraction force on the actuator. It complies with EN 1088 standard (protection against defeat) thanks to its mechanically coded actuator. Flexibility and speed during installation plus high plant availability Compact design Up to four horizontal and four vertical approach directions Innovative connection technology Universal integration - possible to connect to all common control voltages Built-in manipulation protection Long service life Robust design and high mechanical load capacity Heavy duty positive opening safety contacts with galvanic isolation Wide operating temperature range IP67 protection Easy to service cage clamp terminals
1 products found
JPY: 62,000
USD: 388.64
-
PSENrope Cable Switch With E-Stop, Straight, 75m, NC/NO 570300
PSEN Safety Rope Pull Switch. The PSENrope from Pilz is a manually operated rope pull switch used to safely shut down functional processes that extend over a wide area, such as conveyors. It provides maximum safety, as the emergency stop function can be triggered at any point along the rope. Available with either a polyamide or aluminium enclosure which has three M20x1.5 cable entries. When the cover is closed correctly and an equivalent specification cable gland used, IP67 protection can be achieved. Flexible to use as the operating range is limited only by the length of the rope Extremely resilient and suitable for both indoor and outdoor use High level of safety due to the wiring space being physically separate from the mechanics Dual function mushroom type pushbutton with E-STOP and pull-to-release
1 products found
JPY: 51,000
USD: 319.69
-
Pilz 570312 Roller Guide, For Use With PSEN Safety Switch 570312
PSEN Safety Rope Pull Accessories. A range of accessories to support the Pilz PSENrope safety rope pull switch.
1 products found
JPY: 7,820
USD: 49.02
-
Pilz 570313 Rope Pulley, For Use With PSEN Safety Switch 570313
PSEN Safety Rope Pull Accessories. A range of accessories to support the Pilz PSENrope safety rope pull switch.
1 products found
JPY: 3,910
USD: 24.51
-
Pilz PNOZ X3P 24 <arrow/> 240 V V ac/dc Safety Relay Dual Channel With 3 Safety Contacts 777313
CE, cULus Listed, TÜV, KOSHA, CCC. PNOZ X3 Series of Safety Relays by PILZ. The PNOZ X3 range of Safety Relays by PILZ introduces your circuit to a safety related interruption wherein the primary applications are typically in potential hazardous environments where you need that quick power cut off. Particularly useful in automated environments with high foot traffic such as factories and warehouses. Features and benefits. LED indicator statuses to support switching channel status between 1 or 2 signals ; also for monitoring the supply voltage currently in the relay Semiconductor output signals: switch status channel 1 / 2 3 safety contacts and 1 auxiliary contact Several connection outputs ; status indicators Your opening and closing of the safety function relays is tested automatically within each on-off cycle A monitored manual reset is available in this unit DIN rail mounting as standard. Safety features. The circuit is redundant with built in self-monitoring Reliable X3 functionality means your safety function remains effective even in the event of component failure The transformer is short circuit proof and an electronic fuse is used on a DC supply. Applications. Emergency stop buttons Safety gate limit switches Reset buttons Light barriers. Technical safety parameters. EN 60204-1 EN (IEC) 62061 EN ISO 13849-1 VDE 0113-1 EN 60947-5-1
1 products found
JPY: 82,800
USD: 519.03
-
PSENmag ATEX Magnetic Safety Switch, Plastic, 24 V dc 540105
EN60947-5-3 standard is only met if entire system consisting of safety switch (PSENcode), actuator (PSENcode) and a safety monitoring module (PNOZ X or PNOZmulti) is used. EN954-1 (Cat 4), EN60204-1, EN60947-5-3. II 3GD EEx nC IIC T6; TUV. EX8 04 11 20132 014. CE, cULus Listed, ATEX, TÜV, FCC, IC, ECOLAB. Actuator. When the safety gate is closed the switch provides 2 N/C semiconductor outputs. PSENcode Large Non-Contact Safety Switch, Hazardous Area. The PSEN cs1.1p safety switch (stock no. ; 918-6689 918-6689 ) is coded and switches with an actuator from the PSEN cs1.1 series. There is no restriction on the number of times the actuator can be used and reset. The PSEN cs2.13p safety switch (stock no. ; 619-2795 619-2795 ) is fully coded and switches with an actuator from the PSEN cs2.1 series. These actuators must be taught. It can be taught up to a maximum of 8 times but only 1 actuator at a time is taught. Features and Benefits. Series connection, more than 10 safety switches in sequence to Cat 4 of EN954-1 Switch reacts to a single actuator but can be taught a new actuator up to 8 times 5 directions of actuation M12 connection, 8-pin For use in EX area Category 3, Zones 2 and 22 in accordance with EN50021 IP67 protection
1 products found
JPY: 85,200
USD: 534.07
-
Pilz 540010 Bolt and Handle, For Use With PSEN Safety Switch 540010
The PSEN b1 is without escape release and without locking pin. The PSEN b2 is with escape release and has a locking pin (which can be deactivated) to protect the bolt from closing unintentionally. PSENbolt. The PSENbolt from Pilz comprises of a handle and bolt to provide protection against failure and manipulation in areas where safety gates are frequently opened and closed, or difficult to adjust. Ready made solution comprising bolt and handle Space saving due to compact design Mechanical protection of the safety switch ensures long service life Protection from manipulation and defeat in conjunction with the coded safety switch PSENcode Suitable for use on left and right hand gates Slot on bolt to allow a padlock to be fitted to to stop it being opened or closed unintentionally
1 products found
JPY: 56,500
USD: 354.17
-
PSENslock Magnetic Safety Switch, Plastic, 24 V dc 570602
PSENslock Safety Gate System. The PSENslock from Pilz is a non-contact safety gate system which combines safety gate monitoring and a non-contact magnetic interlock in a single unit. The combination of safe position monitoring and process guarding make the PSENslock suitable for universal use and the highest category applications. The magnetic guard locking device is largely non-wearing, compared with mechanical technologies. System optimised for safe position monitoring with process guarding Suitable for the highest safety requirements Highest level of manipulation protection (coding) Process protection through magnetic guard locking Four assembly directions Tolerant to gate misalignment Flexible connectors Optimised for mounting on to 45mm profiles User friendly diagnostics via double sided LED display Ideal for rugged industrial application as it is insensitive to dust and water (IP67) Long product service life as it is mechanically non-wearing
1 products found
JPY: 220,000
USD: 1,379.05
-
Pilz 540020 Bolt and Handle, For Use With PSEN Safety Switch 540020
The PSEN b1 is without escape release and without locking pin. The PSEN b2 is with escape release and has a locking pin (which can be deactivated) to protect the bolt from closing unintentionally. PSENbolt. The PSENbolt from Pilz comprises of a handle and bolt to provide protection against failure and manipulation in areas where safety gates are frequently opened and closed, or difficult to adjust. Ready made solution comprising bolt and handle Space saving due to compact design Mechanical protection of the safety switch ensures long service life Protection from manipulation and defeat in conjunction with the coded safety switch PSENcode Suitable for use on left and right hand gates Slot on bolt to allow a padlock to be fitted to to stop it being opened or closed unintentionally
1 products found
JPY: 65,700
USD: 411.84
-
PSENrope Cable Switch With E-Stop, Side Mount, 75m, 2NO/2NC 570302
PSEN Safety Rope Pull Switch. The PSENrope from Pilz is a manually operated rope pull switch used to safely shut down functional processes that extend over a wide area, such as conveyors. It provides maximum safety, as the emergency stop function can be triggered at any point along the rope. Available with either a polyamide or aluminium enclosure which has three M20x1.5 cable entries. When the cover is closed correctly and an equivalent specification cable gland used, IP67 protection can be achieved. Flexible to use as the operating range is limited only by the length of the rope Extremely resilient and suitable for both indoor and outdoor use High level of safety due to the wiring space being physically separate from the mechanics Dual function mushroom type pushbutton with E-STOP and pull-to-release
1 products found
JPY: 56,900
USD: 356.67
-
Pilz 570314 Rope Pull Kit, For Use With PSEN Safety Switch 570314
PSEN Safety Rope Pull Accessories. A range of accessories to support the Pilz PSENrope safety rope pull switch.
1 products found
JPY: 39,800
USD: 249.48
-
Pilz 570315 Rope Pull Kit, For Use With PSEN Safety Switch 570315
PSEN Safety Rope Pull Accessories. A range of accessories to support the Pilz PSENrope safety rope pull switch.
1 products found
JPY: 79,000
USD: 495.21
-
Pilz 570311 Spring, For Use With PSEN Safety Switch 570311
PSEN Safety Rope Pull Accessories. A range of accessories to support the Pilz PSENrope safety rope pull switch.
1 products found
JPY: 21,400
USD: 134.14
-
PSEN sg2c Solenoid Interlock Switch 24 V dc 570800
EN 60204-1, EN 60947-5-3, EN 62061: SIL CL 3, EN ISO 13849-1: PL e and Cat. 4, EN 1088. EC, TÜV. PSENsgate Safety Gate Monitoring System. Safe guard locking device Safe interlocking Transponder technology 2 safety inputs for series connection of several safety switches 2 safety output Locking pin keeps the bolt tongue from being opened unintentionally Detection of bolt tongue and locking pin breakage Padlock for restart interlock Auxiliary release for opening the safety gate, when the plant's voltage is switched off Escape release for fast release in emergency situations from within the danger zone Suitable for left and right hinged gates Plug-in spring-loaded terminals LED for: supply voltage/fault, gate closed, status of the hazardous machinery, status of the inputs, bolt tongue is engaged. The PSENsgate Safety Gate Monitoring System combines secure safety gate monitoring, safe guard locking and control elements in one system. Also included with this non-contact switch is additional functions such as E-STOP and escape release.
1 products found
JPY: 232,000
USD: 1,454.27
-
PNOZmulti 2 PNOZ m ES Ethernet Communication Module, 24 V dc 772130
CE, cULus Listed, TÜV, BG, CCC. Screw terminals. PNOZmulti 2 Communication/Fieldbus Module ETH. The PNOZ m ES ETH communication module connects to a base unit from the PNOZmulti 2 configurable control system. Features and Benefits. Can be configured in the PNOZmulti Configurator 2 Ethernet interfaces Status indicators for supply voltage, communication and errors Maximum 1 communication module can be connected to the left of the base unit PNOZmulti 2 Transmission rate 10 Mbps or 100 Mbps Connection to fieldbus via RJ45 connector
1 products found
JPY: 61,700
USD: 386.76
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 540000
EN 60947-5-3 with actuator PSEN cs1.1 PDDB; EN 62061 SIL CL 3; EN ISO 13849-1 PLe Cat. 4; EN ISO 14119 coding level Low, Type 4. CE, cULus Listed, TÜV, FCC, IC. PSEN cs1.1 actuator. PSENcode Large Non-Contact Safety Switch, Coded. The PSEN cs1.1p safety switch is coded and only switches when used with an actuator from the PSEN cs1.1 series. There is no restriction on the number of times the actuator can be used and reset. Features and Benefits. Transponder technology for presence detection (safety function) Coded switch Dual-channel operation 2 safety inputs for series connection of multiple safety switches 2 safety outputs 1 signal output LED display for state of the actuator, state of the inputs and supply voltage/fault 4 directions of actuation M12 8 pole male connector IP67 protection. Applications. The PSEN cs1.1p is designed for use in an industrial environment.
1 products found
JPY: 43,900
USD: 275.18
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 542000
The safety level PLe (Cat. 4)/SIL CL 3 is only achieved if the safety outputs use 2-channel processing. EN 60947-5-3; EN 62061 SIL CL 3; EN ISO 13849-1 PLe Cat. 4; EN ISO 14119 Coding level Low, Type4. CE, TÜV, UL/cUL, FCC, IC, ECOLAB. Actuator. PSENcode Slim Non-Contact Safety Switch, Coded. The PSEN cs5.11 and PSEN cs5.1p safety switches are coded and only switch when used with an actuator from the PSEN cs1.1 series. There is no restriction on the number of times the actuator can be used and reset. Features and Benefits. Transponder technology for presence detection Coded switch Dual-channel operation 2 safety inputs for series connection of multiple safety switches 2 safety outputs Safety Device Diagnostics (SDD) Safety Device Diagnostics can be used to poll sensor information, to perform actions and to read configuration parameters Diagnostic input for Y1 for Safety Device Diagnostics (SDD) Signal output/diagnostic output Y32 for Safety Device Diagnostics LED display for state of actuator detection, state of the inputs and supply voltage/fault IP66 / IP67 protection. PSEN cs5.11 (stock no. ; 918-6667 918-6667 ). 1 actuation direction with 3 approach directions: square marking for normal operating distance M12 8 pole male connector 30 N holding force. PSEN cs5.1p (stock no. ; 918-6661 918-6661 ). 4 actuation directions, each with 3 approach directions: square marking for normal operating distance and triangle marking for short operating distance M8 8 pole male connector
1 products found
JPY: 28,700
USD: 179.90
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 542011
The safety level PLe (Cat. 4)/SIL CL 3 is only achieved if the safety outputs use 2-channel processing. EN 60947-5-3; EN 62061 SIL CL 3; EN ISO 13849-1 PLe Cat. 4; EN ISO 14119 Coding level Low, Type4. CE, TÜV, UL/cUL, FCC, IC, ECOLAB. Actuator. PSENcode Slim Non-Contact Safety Switch, Coded. The PSEN cs5.11 and PSEN cs5.1p safety switches are coded and only switch when used with an actuator from the PSEN cs1.1 series. There is no restriction on the number of times the actuator can be used and reset. Features and Benefits. Transponder technology for presence detection Coded switch Dual-channel operation 2 safety inputs for series connection of multiple safety switches 2 safety outputs Safety Device Diagnostics (SDD) Safety Device Diagnostics can be used to poll sensor information, to perform actions and to read configuration parameters Diagnostic input for Y1 for Safety Device Diagnostics (SDD) Signal output/diagnostic output Y32 for Safety Device Diagnostics LED display for state of actuator detection, state of the inputs and supply voltage/fault IP66 / IP67 protection. PSEN cs5.11 (stock no. ; 918-6667 918-6667 ). 1 actuation direction with 3 approach directions: square marking for normal operating distance M12 8 pole male connector 30 N holding force. PSEN cs5.1p (stock no. ; 918-6661 918-6661 ). 4 actuation directions, each with 3 approach directions: square marking for normal operating distance and triangle marking for short operating distance M8 8 pole male connector
1 products found
JPY: 38,900
USD: 243.84
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 540005
EN60947-5-3 standard is only met if entire system consisting of safety switch (PSENcode), actuator (PSENcode) and a safety monitoring module (PNOZ X or PNOZmulti) is used. EN954-1 (Cat 4), EN60204-1, EN60947-5-3. II 3GD EEx nC IIC T6; TUV. EX8 04 11 20132 014. CE, cULus Listed, ATEX, TÜV, FCC, IC, ECOLAB. Actuator. When the safety gate is closed the switch provides 2 N/C semiconductor outputs. PSENcode Large Non-Contact Safety Switch, Hazardous Area. The PSEN cs1.1p safety switch (stock no. ; 918-6689 918-6689 ) is coded and switches with an actuator from the PSEN cs1.1 series. There is no restriction on the number of times the actuator can be used and reset. The PSEN cs2.13p safety switch (stock no. ; 619-2795 619-2795 ) is fully coded and switches with an actuator from the PSEN cs2.1 series. These actuators must be taught. It can be taught up to a maximum of 8 times but only 1 actuator at a time is taught. Features and Benefits. Series connection, more than 10 safety switches in sequence to Cat 4 of EN954-1 Switch reacts to a single actuator but can be taught a new actuator up to 8 times 5 directions of actuation M12 connection, 8-pin For use in EX area Category 3, Zones 2 and 22 in accordance with EN50021 IP67 protection
1 products found
JPY: 62,300
USD: 390.52
-
Pilz PNOZ XV3P 24 V dc Safety Relay Dual Channel With 3 Safety Contacts 777512
EN 60204-1, EN 62061, EN ISO 13849-1, VDE 0113-1, EN 60947-5-1. CE, cULus Listed, TÜV, CCC. PNOZ XV3 Safety Relay. The PNOZ XV3P 3 safety relay provides a safety-related interruption of a safety circuit. It meets the requirements of EN 60947-5- 1, EN 60204-1 and VDE 0113-1. Features and Benefits. Relay outputs, instantaneous 3 safety contacts (n/o), positive-guided Relay outputs, delay-on re-energised: 2 safety contacts (n/o), positive-guided with adjustable or fixed delay-on de-energisation (dependent on unit) LED for operating voltage, LED's for switching positions of all output relays and reset circuit Connection for safety limit switches, E-stops, safety gate switches and for external reset buttons Output circuit is redundant Single or two channel operation Feedback control loop for monitoring external contactors/relays Prevents machine operation in the event of a power supply failure, component failure, coil defect in a relay, cable break and earth fault DIN Rail mounted Screw terminals. Applications. The PNOZ XV3P 3 safety relay is used in applications with E-stops and safety gates.
1 products found
JPY: 107,000
USD: 670.72
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 541010
The safety level PLe (Cat. 4)/SIL CL 3 is only achieved if the safety outputs use 2-channel processing. EN 60947-5-3 with the actuator PSEN cs3.1 PDDB; EN 62061 SIL CL 3; EN ISO 13849-1 PLe Cat. 4; EN ISO 14119 coding level Low, Type4. CE, cULus Listed, TÜV, BG, CCC. Actuator. PSENcode Compact Non-Contact Safety Switch, Coded. The PSEN cs3.1 and PSEN cs3.1p safety switches are coded and only switch with an actuator from the PSEN cs3.1 series. There is no restriction on the number of times the actuator can be used and reset. Features and Benefits. Transponder technology for presence detection (safety function) Coded switch Dual-channel operation 2 safety inputs for series connection of multiple safety switches 2 safety outputs 1 signal output LED display for state of the actuator, state of the inputs and supply voltage/fault 1 direction of actuation IP69K protection Stock no. ; 918-6655 918-6655 has an M12 8 pole male connector Stock no. ; 918-6664 918-6664 has an M8 8 pole male connector
1 products found
JPY: 32,400
USD: 203.10
-
PSENcode Magnetic Safety Non-Contact Switch, Plastic, 24 V dc 542100
The safety level PLe (Cat. 4)/SIL CL 3 is only achieved if the safety outputs use 2-channel processing. EN 60947-5-3 with the actuator PSEN cs6.1PDDB; EN 62061 SIL CL3; EN ISO 13849-1 PLe Cat. 4; EN ISO 14119 coding level high, Type 4. CE, TÜV, UL/cUL, FCC, IC, ECOLAB. Actuator. PSENcode Slim Non-Contact Safety Switch, Fully Coded. The PSEN cs6.1p safety switch is fully coded and switches with an actuator from the PSEN cs6.1 series. The actuators must be taught and can be taught up to a maximum of 8 times but only 1 actuator at a time. Features and Benefits. Transponder technology for presence detection Fully coded switch Dual-channel operation 2 safety inputs for series connection of multiple safety switches 2 safety outputs Safety Device Diagnostics (SDD) can be used to poll sensor information, to perform actions and to read configuration parameters Diagnostic input for Y1 for Safety Device Diagnostics (SDD) Signal output/diagnostic output Y32 for Safety Device Diagnostics LED display for state of actuator detection, state of the inputs and supply voltage/fault 4 actuation directions, each with 3 approach directions: square marking for normal operating distance; triangle marking for short operating distance; 2 semicircle markings for a lateral approach IP66 / IP67 protection M8 8 pole male connector
1 products found
JPY: 40,000
USD: 250.74
-
Pilz 540080 Actuator, For Use With PSEN Safety Switch 540080
CE, cULus Listed, TÜV. PSENcode Large Actuator. The PSEN cs1.1 1 actuator is designed for use with the PSENcode large design non-contact safety switches. Features and Benefits. Transponder technology Large design IP6K9K protection
1 products found
JPY: 5,980
USD: 37.49
-
［Out of stock］PSENmag Magnetic Safety Switch, Plastic, 24 V dc 504220
EN954-1 (Cat 4), EN60204-1, EN60947-5-3. CE, cULus Listed, TÜV. Actuator. Only stock nos. ; 744-8702 744-8702 and ; 824-4918 824-4918 have an LED. PSENmag Non Contact Switches, Square. The PSENmag Non-contact Switch meets the highest safety requirements offers a complete solution that is safe and economical. It is approved up to PLe of EN ISO 13849-1, SIL 3 of EN/IEC 62061 and Category 4 of EN 954-1. Features and Benefits. Connected via a plug connection or with cable Flexible cable outlet, including connector, so there is no need for an angled connector Flexible mounting, both the sensor and the actuator support every conceivable mounting configuration Cost effective thanks to series connection Operating distance of 3 mm or 10 mm Extra signal contact and LED. Applications. The PSENmag safety switch is suitable for use in applications with heavy soiling, thanks to its non-contact design.
1 products found
JPY: 17,400
USD: 109.07
-
［Discontinued］PNOZmulti Series Safety Controller, 20 Safety Inputs, 6 Safety Outputs, 24 V dc 773110
EN954-1 (Cat 2,3,4), EN60204-1, EN61508 (SIL3) and others. UL, CCC, GOST R, TUV, NFPA 79:2002, UL508, OSHA. Plug-in screw terminals and 32K SIM card. Configuration software and pre-license sold separately (stock no. ; 619-2767 619-2767 ). Call Pilz to register, this activates the software and is used for technical queries and support from Pilz. In order to program the controller from your PC you will need an adaptor (stock no. ; 218-239 218-239 ) and cable (stock no. ; 812-926 812-926 ). PNOZmulti Base Unit Base Unit, Safety Functions (Fieldbus only, no Expansion Modules). One system covers both safety-related (E-stop, light curtain etc) and standard control functions Economical non-expandable solution Simple wiring means short commissioning times Simple intuitive programming resulting in time and cost saving Flexible to apply, as only one solution required for applications up to Category 4 (EN954-1) and applications up to SIL 3 (EN61508) Simple, user-friendly diagnostics mean short down-time and high plant availability Compact design, DIN rail mount Certified worldwide
1 products found
JPY: 87,470
USD: 548.30
-
［Discontinued］PNOZmulti Series Safety Controller, 20 Safety Inputs, 6 Safety Outputs, 24 V dc 773100
EN954-1 (Cat 2,3,4), EN60204-1, EN61508 (SIL3) and others. UL, CCC, GOST R, TUV, NFPA 79:2002, UL508, OSHA. Plug-in screw terminals and 32K SIM card. Configuration software and pre-license sold separately (stock no. ; 619-2767 619-2767 ). Call Pilz to register, this activates the software and is used for technical queries and support from Pilz. In order to program the controller from your PC you will need an adaptor (stock no. ; 218-239 218-239 ) and cable (stock no. ; 812-926 812-926 ).
1 products found
JPY: 153,700
USD: 963.46
