Digilent

Digilent 240-021-2 for use with 12-Pin Pmod Board　240-021-2

2 x 6-pin gender changers, right-angle male header, 12-pin gender changer. Pmod Cable Kit, 12-pin. These extension cables let you locate a Pmod 150mm away from its host board, or use a 12-pin Pmod on a system board with only two 6-pin Pmod headers available.

Digilent

Digilent Pmod MAXSONAR Maxbotix Range Finder Expansion Board 240-071　240-071

Pmod MAXSONAR Range Finder. The Pmod MAXSONAR is a single-transducer ultrasonic range finder based on the MaxBotix® LV-MaxSonar®-EZ1™ module. Effective object detection range: 150 to 6480mm Distance resolution: 25mm over detection range Free-run operation readings every 50ms Host communication: UART, PWM and Analogue Dimensions: 23 x 20mm

Digilent

Digilent Analog-to-Digital Converter Expansion Module 410-064　410-064

Pmod AD1 Dual 1Msps 12-bit ADC. The Digilent Pmod AD1 is a two-channel, 12-bit ADC module featuring the Analog Devices AD7476A device. Simultaneous A/D conversion at up to 1MSPS per channel Dual 2-pole Sallen-Key anti-alias filters Host communication: SPI bus 6-pin Pmod connector with GPIO interface Dimensions: 24 x 20mm

Digilent

Digilent Pmod RS232 Expansion Module 410-068　410-068

Pmod RS232 UART-RS232 Converter. The Pmod RS232 converts the digital logic-voltage levels of a UART device to RS-232 voltage levels required by a PC COM port for example. The RS-232 module is configured as a Data Communications Equipment (DCE) device, it connects to Data Terminal Equipment (DTE) devices such as a PC serial COM port, using a straight-through cable. Whats on-board? MAX3232 RS-232 transceiver device Standard DE9 female connector for RS-232 output Jumper links for optional RTS/CTS flow control when available Follows Digilent Pmod Interface Specification Type 3 Dimensions: 25 x 33mm

Digilent

Digilent Expansion Module 410-113　410-113

Pmod DA2 Dual 12-bit DAC. The Pmod DA 2 is a dual 12-bit Digital-to-Analogue converter module featuring the Texas Instruments DAC121S101 device. 2 x simultaneous conversion channels Settling time: 8μs Power down mode Host communication: serial 6-pin Pmod connector with GPIO interface Dimensions: 25 x 20mm

Digilent

Digilent Pmod BB Breadboard Expansion Board 410-136　410-136

Solderless breadboard. Pmod BB Wire-Wrap/Breadboard. The Pmod BB is a prototyping board with a 266 point grid of solder pads for custom development. A solderless breadboard is also provided which can be stuck on the board instead. 266 tie-point solder area Optional 170 tie-point solderless breadboard Additional Pmod host port Jumper links to tie port power pins together 2 x 12-pin port signal breakout headers Dimensions: 89 x 38mm

Digilent

Digilent LED Expansion Module 410-163　410-163

Pmod 8LD 8 x HB LEDs. The Digilent Pmod 8 LD features eight high-brightness LEDs driven by logic level transistors so that each LED can be individually illuminated from a logic high signal. 8 x High-Brightness green LEDs Logic-level inputs (Logic 1 = LED on) 2 ;font face="symbol">´ ;/font> 6-pin Pmod connector with GPIO interface Dimensions: 28 x 20mm

Digilent

Digilent 410-183 Basys Artix-7 Development Board　410-183

Basys 3 Artix-7 FPGA Trainer Board. The Basys 3 is an entry-level FPGA development board designed for the Vivado Design Suite, featuring Xilinx Artix-7 architecture. Vivado Design Suite WebPACK edition can be downloaded for free from Xilinx. Expanded features are available through purchase of the Design Edition. Xilinx Artix-7 FPGA (XC7A35T-1CPG236C) 33280 logic cells in 5200 slices (each slice contains 4 x 6-input LUTs and 8 x flip-flops) 1800Kbit Fast Block RAM 5 x Clock Management Tiles, each with a phase-locked loop (PLL) 90 x DSP slices Internal clock speeds exceeding 450MHz On-chip Analogue-to-Digital Converter (XADC) On-board 32Mbit Quad-SPI Serial Flash memory Programmable over JTAG, Quad-SPI or USB USB-UART Bridge via microUSB socket USB-A HID Host socket for mice, keyboards and memory sticks 12-bit VGA display output on DE15 connector FPGA Programming-Done LED 16 x User LEDs 4-digit 7-segment LED display 5 x User Pushbuttons 16 x User Slide-Switches 3 x Standard Pmod 2 x 6-pin connectors Dual purpose XADC signal / Standard Pmod 2 x 6-pin connector Powered from either USB socket or external +5V header

Digilent

Digilent 410-249 Programmer Adapter for use with Xilinx FPGAs　410-249

Xilinx JTAG 2 x 7-pin 2mm connector adapter, USB cable. This cable is not needed for Digilent Xilinx FPGA boards as they have this functionality built-in. JTAG-HS2 FPGA Programming Cable. The JTAG - HS 2 programming cable allows high-speed programming of Xilinx FPGA devices from a host PC. Features. Compatible with all Xilinx tools Compatible with IEEE 1149.7-2009 Class T0 - Class T4 (includes 2-Wire JTAG) On-board ADP123AUJZ 300mA voltage regulator Separate Vref drives JTAG/SPI signal voltages Vref can be any voltage between +1.8V and +5V USB 2.0 HS port drives JTAG/SPI bus at up to 30Mbit/sec JTAG/SPI frequency settable by user PC connector: MicroUSB JTAG connector: 0.1in 6-pin SPI programming modes 0/2 up to 30Mbit/sec, modes 1/3 up to 2Mbit/sec Fully supported by Digilent's Adept software and Adept SDK. Supported Target Devices. Xilinx FPGAs Xilinx Zynq-7000 Xilinx CoolRunner™/CoolRunner-II CPLDs Xilinx Platform Flash ISP configuration PROMs Selected third-party SPI PROMs Selected third-party BPI PROMs. Target Devices Not Supported. Xilinx 9500/9500XL CPLDs Xilinx 1700 and 18V00 ISP configuration PROMs Xilinx FPGA eFUSE programming

Digilent

Digilent Accelerometer Expansion Module 410-255　410-255

Pmod ACL2 3-axis Accelerometer. The Pmod ACL 2 is a 3-axis MEMS accelerometer module featuring the Analog Devices ADXL362 device. Measurement ranges: ±2g, ±4g, ±8g Up to 12-bit resolution on each axis User-selectable resolution Free-fall detection 512-sample FIFO buffer Host communication: SPI bus Follows Digilent Pmod Interface Specification Type 2A Activity/inactivity monitoring Power-saving modes Dimensions: 25 x 20mm

Digilent

Digilent Oscilloscope Adapter BNC Adapter Board, Model 410-263 for use with Analog Discovery 2　410-263

Discovery 2 Kit: Project box, USB cable, 2 x 15 flywire signal cable assembly, 5-pack of 6-pin male headers, ferrite cable snap-on. Discovery 2 USB PC Multi-Function Instrument. The Analogue Discovery 2 is a USB oscilloscope and multi-function instrument that allows users to measure, generate, record and control mixed-signals of all kinds. The optional Discovery BNC Adapter Board provides standard BNC probe connections. Discovery 2 is aimed at engineering students, hobbyists and electronics enthusiasts who can download tutorials and other information from: https://reference.digilentinc.com/reference/instrumentation/analog-discovery-2/start. 2-channel PC USB 14-bit 100Msps Digital Oscilloscope 2-channel 14-bit 100Msps Arbitrary Function Generator Stereo audio headphone/speaker amplifier 16-channel 100Msps Digital Logic Analyzer 16-channel 100Msps Pattern Generator 16-channel Virtual Digital I/O including buttons, switches and LEDs 2 x I/O Digital Trigger signals for linking multiple instruments Single-channel AC/DC Voltmeter Network Analyzer: 1Hz to 10MHz Bode, Nyquist, Nichols transfer diagrams Spectrum Analyzer: Power spectrum and spectral measurements (noise floor, SFDR, SNR, THD, etc.) Digital Bus Analyzers for SPI, I²C, UART and Parallel ports 2 x Programmable Power Supplies (0 to +5V, 0 to -5V) WaveForms 2015 (Mac, Linux and Windows Compatible) software. RS Product Codes. 134-6480 134-6480 410-321 Analogue Discovery 2 Instrument Kit 134-6460 134-6460 410-263 Analogue Discovery BNC Adapter Board

Digilent

Digilent 410-292 Nexys 4 DDR Artix-7 Development Board　410-292

Hardshell plastic case with protective foam, USB cable. Nexys 4 DDR Artix-7 FPGA Trainer Board. The Nexys 4 is an FPGA development board designed for the educational market, featuring Xilinx Artix-7 architecture. The Nexys 4 DDR is compatible with the high-performance Vivado Design Suite as well as the ISE® toolset, which includes ChipScope™ and EDK. WebPACK editions of these toolsets can be downloaded for free from Xilinx. Expanded features are available through purchase of the Design Edition. Xilinx Artix-7 FPGA (XC7A100T-1CSG324C) Features. 101440 logic cells in 15850 slices (each slice contains 4 x 6-input LUTs and 8 x flip-flops). 4860Kbit Fast Block RAM. 6 x Clock Management Tiles, each with a phase-locked loop (PLL). 240 x DSP slices. Internal clock speeds exceeding 450MHz. On-chip Analogue-to-Digital Converter (XADC). Nexys 4 DDR Board Features. MT47H64M16HR-25 128MiB DDR2 SDRAM S25FL128S 16MiB Quad-SPI Serial Flash memory ADXL362 SPI bus 3-axis accelerometer ADT7420 I²C bus temperature sensor ADMP421 MEMS microphone with PDM output Programmable over JTAG, Quad-SPI or USB FPGA Programming-Done LED 2 x 4-digit 7-segment LED displays 16 x User LEDs 2 x User RGB LEDs 5 x User Pushbuttons 16 x User Slide-Switches USB-UART Bridge via microUSB socket USB-A HID Host socket for mice, keyboards and memory sticks 12-bit VGA display output on DE15 connector RJ45 socket for 10/100 Ethernet connection 3.5mm jack socket for mono audio output microSD card slot 4 x Standard Pmod™ 2 x 6-pin connectors Analogue XADC Pmod™ 2 x 6-pin connector Powered from either USB, barrel jack socket or external battery pack

Digilent

Digilent RS-485 Expansion Module 410-310　410-310

Pmod RS485 UART-RS485 Converter. The Pmod RS485 uses the Analog Devices ADM2582E chip to provide RS-485 / RS-422 differential signalling between devices in environments with high electrical noise. High-speed RS-485 differential signalling module Isolated RS-485/RS-422 interfaces for use in noisy environments 16Mbps maximum data rate Connect up to 256 nodes on one bus Differential half- or full-duplex communication Thermal shutdown and ±15kV ESD protection Host communication: serial UART Dimensions: 37 x 20mm

Digilent

Digilent Pmod OLEDrgb Expansion Module 410-323　410-323

Pmod OLEDrgb OLED display. Digilent ‘s Pmod OLEDrgb (Revision B) is an organic RGB LED module with a 96 x 64 pixel display capable of 16-bit colour resolution. Designed to work in conjunction with a host board, communicating via the SPI protocol, the Pmod OLEDrgb is a graphical display that allows users the option to light up any individual pixel on the OLED screen. Utilising a Solomon Systech SSD1331 display controller, the PmodOLEDrgb receives information from the host board to be displayed on the OLED screen. Ideal for displaying a range of information including graphs and text as well as full colour pictures. What ‘s on-board? 20 x 13mm RGB OLED display 96 x 64 pixels 16-bit colour resolution 12-pin Pmod connector w/SPI interface Serial SPI host communication 2x low-power display shutdown modes 35 x 25mm overall size

Digilent

Digilent 410-328-35 Cmod A7 Artix-7 Module　410-328-35

Cmod A7 Artix-7 FPGA DIP Module. The Digilent Cmod A7 is a small 48-pin DIP form factor development board built around a Xilinx Artix-7 FPGA. Ideal for use with solderless breadboards. Xilinx Artix-7 FPGA (XC7A35T-1CPG236C) 33280 logic cells in 5200 slices (each slice contains 4 x 6-input LUTs and 8 x flip-flops) 1800Kbit Fast Block RAM 5 x Clock Management Tiles, each with a phase-locked loop (PLL) 90 x DSP slices Internal clock speeds exceeding 450MHz On-board IS61WV5128BLL-10BLI 512KB SRAM On-board N25Q032A 4MB Quad-SPI Flash memory MicroUSB connector USB-JTAG Programming Circuit On-board FT2232HQ USB-UART Bridge 2 x User LEDs User RGB LED 2 x User Pushbuttons 48-pin DIP connector with 44 x GPIO and 2 x Analogue inputs Standard Pmod 2 x 6-pin connector Power supply: USB or external +3.3V to +5.5Vdc connected to DIP pins

Digilent

Digilent Digital Discovery USB Logic Analyser Portable Logic Analyzer & Digital Pattern Generator 410-338　410-338

Digital Discovery Logic Analyser 2 x 6-flywire assembly, 2 x 16-flywire assembly, USB-A to micro-B cable. For sampling rates over 200Msps, a High Speed Adapter (Digilent Part No. ; 410-349 410-349 ) must be used. Digital Discovery Logic Analyser. Digilent ‘s Digital Discovery™ unit is both a logic analyser and a pattern generating instrument specially designed to help optimize channels as well as both speed and portability. Allowing you to debug and visualize as well as simulate digital signals for most embedded projects. The Digital Discovery is driven by the free WaveForms software. The programmable power supply supplies the Logic Analyser input buffers as well as the Pattern Generator input/output buffers to keep logic-level consistency with the circuit under test. The small and portable unit has been designed for use in a wide range of applications and environments to withstand a variety of conditions. What ‘s on board? Digital Logic Analyser: 8 channels @ 800Msps, 16 channels @ 400Msps or 32 channels @ 200Msps 16-channel 100Msps Pattern Generator 16-channel Virtual Digital I/O including buttons, switches and LEDs Digital Bus Analyser: SPI, I²C, UART and Parallel Programmable Power Supply: +1.2 to +3.3Vdc @ 100mA 2 x I/O digital trigger signals for linking multiple instruments USB communication with host PC via micro-AB connector

Digilent

Digilent 410-346-20 Arty Z7-20 APSoC Zynq-7000 Development Board　410-346-20

Arty Z7 Zynq-7000 Development Board. The Arty Z7-20 is a development platform designed around the Xilinx Zynq-7000™ All Programmable System-on-Chip (AP SoC). The Zynq-7000 architecture integrates a dual-core, 650MHz ARM Cortex-A9 processor with Artix-7 series FPGA logic. This pairing surrounds a powerful processor with a unique set of software defined peripherals and controllers. The Vivado, Petalinux, and SDSoC toolsets each provide a path between defining your custom peripheral set and bringing its functionality up to a Linux OS or 'bare-metal' program running on the processor. Xilinx Zynq-7000 (XC7Z020-1CLG400C). Processor: 650MHz dual ARM Cortex-A9 core Look-up Tables (LUTs): 53200 Flip-flops: 106400 Block RAM: 630KB Clock Management Tiles: 4 Available Shield I/O: 49 DDR3 memory controller with 8 x DMA channels and 4 x AXI3 Slave ports High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO Low-bandwidth peripheral controller: SPI, UART, CAN, I²C Programmable from JTAG, Quad-SPI Flash or microSD card Programmable logic equivalent to Artix-7 FPGA Memory. Board Memory and Power. On-board IS43TR16256A-125KBL 512MB DDR3 SDRAM with 16-bit bus @ 1050Mbps On-board S25FL128S 16MB Quad-SPI Flash with 48-bit unique EUI-48/64™ compatible identifier microSD card slot Powered from USB or +7V to +15Vdc via barrel jack. System Connectivity. 10/100/1000 Ethernet via RJ45 connector USB-UART Bridge via micro-B socket USB-JTAG Programming via micro-B socket USB OTG PHY (supports Host only) via USB-A socket. Audio and Video. HDMI sink port (input) HDMI source port (output) PWM driven mono audio output via 3.5mm jack socket. Switches and LEDs. Reset and Program pushbuttons 4 x User pushbuttons 2 x User slide-switches 4 x User LEDs 2 x User RGB LEDs. Expansion Connectors. chipKIT/Arduino R3 Shield headers 2 x Standard 12-pin Pmod™ connectors

Digilent

Digilent Temperature & Humidity Sensor Expansion Module 410-347　410-347

Library and example code available at: reference.digilentinc.com/reference/pmod/pmodhygro/. Pmod HYGRO Humidity/Temperature Sensor. The Pmod HYGRO module is a relative humidity sensor with integrated temperature sensor for highly accurate measurements at low power. Relative Humidity Accuracy: ±2% Temperature Sensor Accuracy: ±0.2°C Good stability at high humidity 14-bit measurement resolution Internal resistive heating element 6-pin Pmod connector with serial I²C bus interface Pass-through Pmod host port for I²C bus daisy-chaining

Digilent

Digilent Pmod VGA Development Board Development Board 410-345　410-345

Digilent

Digilent Oscilloscope Probe, Probe Type: Passive 6MHz 1:10　460-004

Digilent

Digilent Pmod SSD 7-Segment Display 410-126　410-126

Digilent

Non-Isolated DC-DC Converter, ±12V dc Output, 100mA　410-293-A

PowerBRICK • PowerBRICK is a split-rail power supply designed to be used with solder-free breadboards. Generates both negative and positive voltage rails on a single + 5V USB Vbus input.
RS Product Code

Digilent

Non-Isolated DC-DC Converter, ±9V dc Output, 130mA　410-293-B

PowerBRICK • PowerBRICK is a split-rail power supply designed to be used with solder-free breadboards. Generates both negative and positive voltage rails on a single + 5V USB Vbus input.
RS Product Code

Digilent

Non-Isolated DC-DC Converter, ±5V dc Output, -200 mA, 250 mA　410-294-A

PowerBRICK • PowerBRICK is a split-rail power supply designed to be used with solder-free breadboards. Generates both negative and positive voltage rails on a single + 5V USB Vbus input.
RS Product Code

Digilent

Digilent, DC Motor Controller, Voltage Control, 3.125 → 5.5 V, 10 mA　410-333

2.5 mm Vinyl Chloride Tube 610 mm in Length
Use only for pressure measurement of dry air. Not suitable for liquids.

Digilent

Digilent Blue OLED Display 128 x 32pixels SPI Interface　410-222

Pmod OLED 128x32pixel Mono OLED Display. The Pmod OLED is a 128 x 32pixel monochrome organic LED (OLED) panel featuring a Solomon Systech SSD1306 controller and a UG-2832HSWEG04 display from Univision Technology Inc. 128 x 32pixel graphic monochrome OLED display Internal display buffer 16 x brightness settings Host communication: serial SPI bus 12-pin Pmod connector with SPI interface Dimensions: 45.7 x 20.3mm

Digilent

［Discontinued］Digilent 240-035 Target Cable for use with PICkit 3 Programmer　240-035

6-pin gender changer, 6-pin right-angle male header. PICkit™ 3 Programming Cable Kit. A 150mm long 6-way cable set for connecting a chipKIT™ board to the Microchip PICkit™ 3 debugger/programmer.

Digilent

［Discontinued］Digilent, 12 V dc, 2.2 (Stall) kgf.cm, 0.3 kgf.cm, Brushed DC Geared Motor, Output Speed 639 rpm, 15000 rpm, 789 (No　290-006

2mm mounting screws. DC Motor/Gearbox + Quadrature Encoder. Rugged motor/gearbox/encoder set suitable for use with automation/robotic projects. 12V Brushed DC Motor with 1:19 reduction gearbox Stall current: 2.4A Stall torque: 2.2kgf-cm No-load speed: 789rpm ±15% Output shaft diameter: 4mm Rotation sensor: 2-channel Hall sensor in phase quadrature. Accessory Pmod™ Driver Board. 134-6447 134-6447 410-106 Pmod HB5 2A H-bridge Driver Module

Digilent

［Discontinued］340-002, Breadboard Solderless Breadboard Kit　340-002

4 x 4mm screw power supply terminals, 5 x adhesive rubber feet. Digilent Solderless Breadboard, Large. Large solderless breadboard with rugged steel backing. 3 x 630 tie-point terminal strips 5 x 100 tie-point distribution strips. Accessory Plug-in Power Supply Modules. 134-6469 134-6469 410-294-B PowerBRICK +/-3.3V Breadboard USB PSU 134-6468 134-6468 410-294-A PowerBRICK +/-5V Breadboard USB PSU 134-6467 134-6467 410-293-B PowerBRICK +/-9V Breadboard USB PSU 134-6466 134-6466 410-293-A PowerBRICK +/-12V Breadboard USB PSU

Digilent

［Discontinued］Digilent H-Bridge Expansion Module 410-069　410-069

Pmod HB3 2A H-bridge Driver. The Pmod HB3 features a full H-Bridge driver circuit for driving a brushed DC motor from the system board. Two external pins are provided for optional sensor feedback from the motor. Drives a brushed DC motor up to +12V @ 2A Logic-level Direction select input pin Logic-level PWM Speed control input pin Screw terminals for motor connection Screw terminals for motor power supply Header for external QE feedback sensor connection 6-pin Pmod port with GPIO interface Dimensions: 20 x 30mm

Digilent

［Discontinued］Digilent H-Bridge Expansion Module 410-106　410-106

Pmod HB5 2A H-bridge Driver. The Pmod HB 5 features a full H-Bridge driver circuit for driving a brushed DC motor from the system board. Functionally identical to the Pmod HB3, it differs in that the motor connection is a 6-pin JST socket compatible with Digilent motor/gearboxes (Example: RS ; 134-6440 134-6440 ). Drives a brushed DC motor up to +12V @ 2A. Logic-level Direction select input pin. Logic-level PWM Speed control input pin. 6-pin JST connector for direct connection to Digilent motor/gearboxes. Screw terminals for motor power supply. 6-pin Pmod port with GPIO interface. Follows Digilent Pmod Interface Specification Type 5. Dimensions: 20 x 30mm

Digilent

［Out of stock］Digilent 410-316 Nexys Video Artix-7 Development Board　410-316

Hardshell plastic case with protective foam, USB cable. Nexys Video Artix-7 FPGA Trainer Board. The Nexys Video FPGA Board features a large, high-capacity Artix-7 FPGA device, generous external memories, high-speed digital video ports and a 24-bit audio codec. It is perfectly suited for audio and video processing applications. Compatible with ISE® toolset and the Vivado® Design Suite. It is also supported under the free WebPACK™ license. Xilinx Artix-7 FPGA (XC7A200T-1SBG484C) Features. 215360 logic cells in 33650 slices (each slice contains 4 x 6-input LUTs and 8 x flip-flops) 13Mbit Fast Block RAM 10 x Clock Management Tiles, each with a phase-locked loop (PLL) 740 x DSP slices Internal clock speeds exceeding 450MHz On-chip Analogue-to-Digital Converter (XADC) Up to 3.75Gbps GTP transceivers. Nexys Video Board Features. MT41K256M16HA-187E 512MiB DDR3 SDRAM S25FL256S 32MiB Quad-SPI Serial Flash memory 24AA025E48 EEPROM for Ethernet node MAC address ADAU1761 SigmaDSP stereo audio codec HDMI output connector HDMI input connector Programmable over JTAG, Quad-SPI or USB 0.91in 128 x 32pixel OLED display FPGA Programming-Done LED 8 x User LEDs 5 x User Pushbuttons 8 x User Slide-Switches MicroUSB (JTAG) connector for USB programming USB-UART Bridge via microUSB socket USB-A HID Host socket for mice, keyboards and memory sticks DisplayPort output mDP connector 160-pin LPC FMC connector RJ45 socket for 10/100/1000 Ethernet connection 3.5mm jack socket for mono microphone In 3.5mm jack socket for stereo audio Line In 3.5mm jack socket for stereo audio Line Out 3.5mm jack socket for stereo headphone Out microSD card slot 3 x Standard Pmod 2 x 6-pin connectors Dual Analogue/Digital XADC Pmod 2 x 6-pin connector Powered from barrel jack socket or external +12Vdc header

Digilent

［Discontinued］Digilent 410-319 Arty Artix-7 Development Board　410-319

An adapter Shield allowing up to five more Pmod™ peripheral modules to be interfaced is available: RS ; 136-8283 136-8283 Software Voucher Code is provided on the product packaging. Arty Artix-7 FPGA Development Board. Arty is a development platform designed around the Artix-7™ Field Programmable Gate Array (FPGA) from Xilinx. Arty was designed specifically for use as a MicroBlaze Soft Processing System. Xilinx Artix-7 FPGA (XC7A35T-1CSG324-1L). 33280 logic cells in 5200 slices (each slice contains 4 x 6-input LUTs and 8 x flip-flops) 1800Kbit Fast Block RAM 5 x Clock Management Tiles, each with a phase-locked loop (PLL) 90 x DSP slices Internal clock speeds exceeding 450MHz On-chip Analogue-to-Digital Converter (XADC) Programmable over JTAG and Quad-SPI Flash. Board Memory and Power. 256MB DDR3L SDRAM with 16-bit bus @ 667MHz 16MB Quad-SPI Flash memory USB-JTAG Programming circuit Powered from USB connector or +7V to +15Vdc barrel jack socket. System Connectivity. 10/100 Ethernet via RJ45 connector USB-UART Bridge via microUSB socket. Switches and LEDs. 4 x User Slide-Switches 4 x User Pushbuttons Reset Pushbutton Status LEDs: Power-on, FPGA programming status and USB/Ethernet port status 4 x User LEDs 4 x User RGB LEDs. Expansion Connectors. 2 x Standard Pmod™ 2 x 6-pin connectors 2 x High-Speed Pmod™ 2 x 6-pin connectors chipKIT/Arduino R3 Shield headers

Digilent

［Discontinued］Digilent Inertial Sensor Expansion Module 410-326　410-326

Pmod NAV Inertial Navigation Unit. The Pmod NAV uses the LSM9DS1 3-axis accelerometer/gyroscope/magnetometer, plus the LPS25HB digital barometer to provide the basics of an Inertial Measurement Unit (IMU). ±2/4/8/16g linear accelerometer ±245/500/2000dps gyroscope ±4/8/12/16gauss magnetometer 260-1260hPa piezoresistive pressure sensor Embedded temperature sensors for compensation Host communication: SPI bus Follows Digilent Interface Specification Type 2A Dimensions: 20 x 20mm

Digilent

［Discontinued］Digilent OpenScope MZ Series OpenScope MZ Oscilloscope, PC Based, 2, 10 (User Programmable), 2 (Oscilloscope) Channels,　410-324

Digilent

［Discontinued］Digilent 471-015 Zynq-7000 ARM/FPGA SoC Development Board Development Board Zybo Z7-20　471-015

Digilent

［Discontinued］Non-Isolated DC-DC Converter, ±3.3V dc Output, -320 mA, 350 mA　410-294-B

PowerBRICK • PowerBRICK is a split-rail power supply designed to be used with solder-free breadboards. Generates both negative and positive voltage rails on a single + 5V USB Vbus input.
RS Product Code

Digilent

［Discontinued］Digilent 410-317 TFT LCD Colour Display / Touch Screen, 2.8in QVGA, 320 x 240pixels　410-317

Multi-Touch Display Shield for Arduino. The Multi-Touch Display Shield is a 2.8in touchscreen TFT colour display with a PIC32 on-board microcontroller for graphics processing tasks. A highlight of the Multi-Touch Display Shield is the programming experience provided by its Multi-Touch Display System (MTDS) Firmware and the associated libraries. The libraries are supported in Arduino IDE and Xilinx SDK, and have been tested with Arduino, chipKIT and Arty host boards. 2.8in 320 x 240p (QVGA) TFT display with 16-bit colour 2-finger capacitive multi-touch panel On-board 200MHz PIC32MZ 32-bit microcontroller Host communication: serial SPI bus microSD card slot Arduino Uno V3 Shield headers for host connection On-board libraries with 100+ API functions