[WORLDTOOL (Astro Products)] AllProducts
Lab Instruments & Supplies
-
Emergency Supplies
Factory Work Tools & Supplies
-
Work Tools, Supplies
-
Production Processing Equipment
-
Construction Equipment
-
Office Housing Supplies
-
Oil Filter Pliers 2009000003040
This is a plier type oil filter remover.
The plier type makes it easy to apply force, so you can remove the filter which is hard to remove.1 products found
JPY: 1,400
USD: 8.71
-
2PC Hose Remover Set 2007000010754
It is useful for removing a hose that has become stuck during the removal of a radiator hose or a rubber intake joint.
The rubber grip is easy to grip.1 products found
JPY: 710
USD: 4.42
-
T-type spr Ring Hook 2007000002001
This hook can be used when pulling muffler springs or side stand springs.
1 products found
JPY: 700
USD: 4.36
-
Tire Lever Grip 2002000011664
The R-shaped tip makes it difficult to damage the wheel rim.
We recommend that you use them in pairs.1 products found
JPY: 1,400
USD: 8.71
-
Lock type caliper piston tool 2007000011089
This is a plier used to remove the piston of the disc brake caliper.
With a locking mechanism to keep the piston in a restrained state.1 products found
JPY: 3,290
USD: 20.47
-
Brake piston cube 2007000000526
It is mainly used for turning back the piston of the rear disc brake.
The protrusion coming out of the cube fits and secures into the groove of the piston, making it easy to rotate the piston.1 products found
JPY: 810
USD: 5.04
-
Rigid Rack 2 t pin with rubber 2PC 2007000004296
A rigid rack that is held when a vehicle is jacked up.
You can adjust the height for each stage and pin it.1 products found
JPY: 4,670
USD: 29.06
-
2PC Low floor rigid Rack 3 t pin with rubber 2007000010655
Since it is a low floor type, it is suitable when using the lowest jack or when working in a low position.
Also, it has a rubber pad, so it is hard to scratch the surface.1 products found
JPY: 5,900
USD: 36.71
-
Sheet creeper 2003000002201
A parts tray is attached under the sheet, so you can place parts, screws, tools, etc. removed during work.
The seat creeper is just the right height to sit and work.1 products found
JPY: 4,050
USD: 25.20
-
Roller Sheet 2007000005354
It is a castor mobile chair that eases the burden on the lower back.
It also comes with a small tray and can be moved with tools and parts.1 products found
JPY: 5,500
USD: 34.22
-
Jack MZJ01 2007000000687
The jack handle is removable and has a 21 mm HEX shape when removed.
It can also be used on Bic scooters and domestic American bikes.1 products found
JPY: 9,500
USD: 59.11
-
Motor Cyclades Ruby Iodide Breaker Black 2007000011263
Bead breaker used for dropping tire beads for motorcycles.
Supports up to 150 mm (6 inch) wide tires and is mainly used for small bike tires.1 products found
JPY: 4,050
USD: 25.20
-
Lightweight aluminum ladder Flat 1PC 2007000011171
It is a folding ladder rail made of aluminum that is convenient when loading two-wheeled vehicles.
Since it uses an arch type, it is suitable for vehicles with low vehicle height.1 products found
JPY: 14,110
USD: 87.79
-
Bicycle Display Stands 2003000003673
This is a simple type rear stand for bicycles used with the hub of the rear wheel in between.
The height can be adjusted by opening the unit.1 products found
JPY: 1,520
USD: 9.46
-
Pick appt Rack Box 2003000002027
Large capacity multipurpose aluminum box.
Just the right size for the back of a light truck.1 products found
JPY: 28,500
USD: 177.33
-
Gasoline Can 3L and others
3 products found
JPY: 2,500-
USD: 15.56-
-
Stainless Steel Gasoline Can 10L and others
2 products found
JPY: 12,900-
USD: 80.26-
-
Shield Leiber Set 2007000000021
Seal screwdriver that can drive oil seals straight in.
The resin attachment makes it difficult to damage the object.1 products found
JPY: 3,700
USD: 23.02
-
11PC Bearing Puller-Set 2007000010310
Puller set for removing inner type bearing.
It can be used for a wide range of work such as wheel bearings for two-wheelers and bearings for water pumps, as it can accommodate a wide range of diameters from φ8 to φ34 mm.1 products found
JPY: 19,900
USD: 123.82
-
Stud Bolt Remove & installer 2007000010334
A set of stud bolt installers and removers.
By separating the installer from the remover, the thread can be removed and inserted without crushing.1 products found
JPY: 5,500
USD: 34.22
-
M/C disc brake piston tool 2007000011720
Compact type ideal for pushing back disc brake pistons for small vehicles such as motorcycles.
The plate is equipped with two types, the thin side and the thick side. By using the thick side, the brake piston of the automobile can be used.1 products found
JPY: 7,000
USD: 43.55
-
Drums Pump (aluminum) 2009000002043
Depending on the depth, the length of the inner tube can be changed to accommodate 50 L, 100 L and 200 L drums.
You can easily suck up the oil by stroking the lever up and down.1 products found
JPY: 5,500
USD: 34.22
-
Long neck Poly Drum Funnels 2009000004269
Long nozzle funnel.
Since the nozzle is long, it is suitable for use in deep places.1 products found
JPY: 340
USD: 2.12
-
Oil Poly Drum Funnels 200mm 2009000004283
It is a large diameter funnel.
Because of its large diameter, it is suitable for injecting many liquids.1 products found
JPY: 400
USD: 2.49
-
Blind Bearing Puller-Plastic Case 2010000000021
Slide hammer type puller for 8~30 mm inner diameter bearings.
It is a type that adheres to the inside, and can be used even in narrow places.1 products found
JPY: 21,900
USD: 136.26
-
Bolt Type puller 13 Piece Set 2010000000625
Install the supplied bolt into the service hole of the object and install the puller.
Various bolts of millimeter and inch are included in the set, so it can be used for various vehicles and equipment.1 products found
JPY: 1,900
USD: 11.82
-
Giapular thin claw 2010000000632
Thin-claw type puller.
The nail is a sliding type that moves independently from left to right.1 products found
JPY: 3,490
USD: 21.72
-
Tie-rod End Puller 2007000013526
This is a special tool used to remove tie rod ends and ball joints.
The lifting amount can be adjusted to two levels by changing the position of the pin.1 products found
JPY: 3,500
USD: 21.78
-
Tool Box 2003000007633
It is a portable size tool box for storing and storing tools.
It is a tool box of portable size, but with storage space inside the lid and 3 drawers, it has storage capacity.1 products found
JPY: 8,110
USD: 50.46
-
Brake Piston Tool 2007000012994
This tool pushes back the disc brake piston.
Can be used for single type, parallel type, opposite 2-piston type, etc.1 products found
JPY: 4,200
USD: 26.13
-
Mini Bearing Separator Set 2007000013366
This puller is a set of a separator and a nail puller.
Can be used to remove bearings, gears and pulleys.1 products found
JPY: 4,200
USD: 26.13
-
Plastic Ladder 2007000013625
It is a ladder rail that is used when the height needs to be secured when using a jack.
The slope is gentle and the lift is low, so it can be used for vehicles with low vehicle height.1 products found
JPY: 4,350
USD: 27.07
-
An Oil Pan 7L 2009000003743
It is an oil pan with a handle.
Since oil can be discharged from the nozzle, waste oil can be easily disposed of without spilling.1 products found
JPY: 700
USD: 4.36
-
Oil Pan Square 2009000004108
It is an oil pan with a net that is useful when you cut the oil from the oil filter or place the removed drain bolt.
It has a discharge port which is useful for discharging waste oil.1 products found
JPY: 700
USD: 4.36
-
Wire injector 2009000004467
Since the wire can be pressed in two places, the lubricant does not leak easily.
Lubricant can be fed directly into the inner wire by simply inserting the outer wire and injecting the lubricant through the injection port.1 products found
JPY: 800
USD: 4.98
-
Air Tire Gauge 2001000008476
This is an air tire gauge for filling tires such as cars and motorcycles with air by connecting to an air compressor.
Since it is connected to the valve of the tire with a clip chuck, there is no need to press the chuck against it during filling.1 products found
JPY: 1,600
USD: 9.96
-
Wrench Rack and others
2 products found
JPY: 500-
USD: 3.11-
-
Oil Tool Extractor 2009000004702
This is a manual type extractor that does not require a power source and removes oil from oil level gauge guides and oil filler openings.
Two types of hoses with different outer diameters can be used according to the oil viscosity.1 products found
JPY: 3,500
USD: 21.78
-
Pick-up tool 2007000001219
Catch small parts that are out of reach with four fingernails on the tip.
It is flexible and can be folded freely.1 products found
JPY: 440
USD: 2.74
-
Cowling Holder 2007000003572
A convenient bonnet holder that can be easily fixed by stretching and twisting.
The tip has a non-slip rubber leg to prevent scratches on objects.1 products found
JPY: 1,400
USD: 8.71

