VESSEL CO., INC.

Electrostatic Measuring Equip Eye-02　EYE-02

It is a compact electrostatic meter that can measure ion balance and charging potential.
It comes with a "maximum value (peak value) display" function which is convenient for charging and "continuous measurement" of "work running at high speed" where numerical values are hard to be determined.

HAKKO

Ground wire FG -450　B3584

Product Name: Ground Wire

HAKKO

Ion balance plate for FG-450　B3585

Product Name: Ion Balance Plate (With Screws)

HAKKO

Body charging level measurement plate　B3586

Product Name: Anthropometric Electrostatic Measurement Plate (With Screws)

HAKKO

Electrostatic level meter　FG450-01

Electrostatic electricity level meter that can check the charging status of film, resin, etc. • Rotary sensor heads hold at 45 degrees each and rotate at 180 degrees, allowing you to set the display in a position that is easy to read in any situation.
An ion balance plate is included as standard, so you can use the ion balance plate as well as electrostatic potential measurement to check the static electricity removal device. The ion balance can be measured in 1V units.

HAKKO

Static electricity level meter calibrated　FG450-02

Electrostatic electricity level meter that can check the charging status of film, resin, etc. • Rotary sensor heads hold at 45 degrees each and rotate at 180 degrees, allowing you to set the display in a position that is easy to read in any situation.
An ion balance plate is included as standard, so you can use the ion balance plate as well as electrostatic potential measurement to check the static electricity removal device. The ion balance can be measured in 1V units.

KOGANEI

EP Sensor DTYEPS Series　DTY-EPU-3LD

It has a small piezoelectric transformer and can be used to supply a constant voltage DC power supply. Blow type, fan type, bar type, etc. are available.
We have a lineup of sensors that are ideal for daily static electricity measurement management and fixed point monitoring of production lines.

KOGANEI

EP Sensor DTYEPS Series　DTY-EPU-B-3LD

It has a small piezoelectric transformer and can be used to supply a constant voltage DC power supply. Blow type, fan type, bar type, etc. are available.
We have a lineup of sensors that are ideal for daily static electricity measurement management and fixed point monitoring of production lines.

DESCO

Wrist Strap & Shoes Checker w/Dual Foot Plate and others

DESCO

Two Point Resistance Probe　19297

Probe for measuring resistance between 2 points (2 pins) for small area or small space
Gold plated spring load pin electrode with conductive rubber

DESCO

Low resistance tester　19249

Measure the ground resistance between the banana jack and other devices.
Select the test range of pass/fail: less than 1 Ω, less than 2 Ω, less than 10 Ω

DESCO

AC Adapter for Continuous Monitor IEC Plug　19258

Can be used in combination with Desco part numbers 19228, 19218 and 19247.

DESCO

AC Adapter for Continuous Monitor　19260

Replacement adapters for the following Desco standards 19205, 19208, 19212, 19214, 19215, 19216, 19217, 19218 19220, 19222, 19226, 19228, 19230, 19232, 19246; 94343, 98227
Made in the USA as 100~120VAC adapter for constant monitor

DESCO

Tester for Wrist Strap　19350

Quick and easy installation to ground both the wrist strap and the workbench mat
Test all circuits including wrist strap, cord and skin contact

DESCO

Portable Test Kit Upgrade for Ionizers　19440

This is a portable tool for testing ionizers according to ANSI/ESD SP3.3.
Conductive plate and charger set.

DESCO

Charging Plate for Field Meter　19441

19492 Electrifying Plate for Digital Electrostatic Measurements
Made in the USA

DESCO

Conductive Current Tester 0 -10Ω 0 -600V AC/DC　35100

Batteries are not included. Two AAA batteries are required to test a non-power circuit
The low voltage lamp tests a non-power circuit

DESCO

Conductive Tester 0 -50 Ω with Acoustic　35135

Highly audible 2 kHz loud sound, easy to check the continuity of the electrical circuit
Probe: Up to 270 mm 3 V

Surface Electrometer AS Mini2　AS-20

The use of a rotary sensor head makes it convenient and safe to measure from a narrow place or on a transport line.
The head part rotation angle is held at 180 degrees and 45 degrees each.

HASEGAWA Electric Co., Ltd.

［Discontinued］High-Voltage Live Line Alarm　HX6

A buzzer sound is used to alarm the approach to the high voltage charging section.
Ideal for electrical work safety.

ATOM KOUSAN Corporation

［Discontinued］Petermoba　PM-05B

It is a transfer tool that transfers minute parts by adhesive rubber at the tip.
It does not need to be pinched like tweezers, and can capture fine parts just by touching the tip of the capture plate, and can be dissociated just by pulling the sliding knob after transferring to a predetermined place.

MIDORI ANZEN CO., LTD.

［Discontinued］Anti-static Shose / Liststrap Checker MES-300　MES-300

Electrostatic shoes can be checked individually on the left and right sides.
You can select the upper and lower limit of the judgment level.

3M Company

［Discontinued］Wrist Strap Tester　746

Because it can be mounted on a wall or installed on a work bench, it can be checked regularly, inspected before work, and recorded quickly and easily.
This tester can measure the total resistance value including the human body by simple operation.

HOZAN TOOL INDUSTRIAL CO., LTD.

［Discontinued］Electrode (clothing)　F-103

Measurement electrode for clothing that meets the standard for static electricity protection (RCJS, IEC).
Combined with F-100, resistance measurement of anti-static clothing is possible.

HOZAN TOOL INDUSTRIAL CO., LTD.

［Discontinued］Wrist Straps Checker and others

HOZAN TOOL INDUSTRIAL CO., LTD.

［Discontinued］Electrostatic sampling Checker　Z-201

For detecting static electricity.
A dedicated checker that checks for the presence of static electricity in the workplace.

KOGANEI

［Discontinued］EP Sensor DTYEPS Series 　front protective cover　KB100

DESCO

［Discontinued］Monitor Continuous Multi Mount　19651

Constant monitoring of the wrist strap's grounding path and resistance detection in the range as low as 1 MΩ is more stable (compared to pulsed or intermittent).
An alarm sounds when a banana plug inserted into a worker's wrist strap cord or monitor jack is unexpectedly released.

DESCO

［Discontinued］Full-Time Continuous Monitor 100 V　19325

This is a single-station constant monitor for checking the ground condition of workers, work surfaces, and workers. • Waveform strain detection technology provides constant real-time monitoring of the worker's ground path and whether there is a 1 MΩ resistance. • Parking snap function. • Dual LED lamp and alarm sound function for monitoring workers and work tables. • Alarm signal. • Can be connected to an external relay (refer to relay box part number 50547). • Can be used in conjunction with a single-wire wrist strap. • Calibration unit for accurate on-site performance and conformity testing. Refer to Desco part number 98220. • NIST calibration certificate. • Made in the USA.

DESCO

［Discontinued］Digital Static Field Meter　19492

This is a portable static electricity meter.
Accuracy is guaranteed even if you use it repeatedly.

［Discontinued］HAKKO　498

Simply connect the ground wire and press the pad with your hand. If it passes, the green GOOD light will light and the buzzer will sound.

［Discontinued］HAKKO FG 460 100V flat type Plug　FG460-81

It fully supports JIS T 8103:2010.
It can support the measurement of electrostatic shoes and conductive shoes from the old standard to the new standard.