Sakaguchi E.H VOC Corp.

67-6668-82　Polyimide Heater Samicon MPI Type 25.4 x 76.2 mm 28 V 15 W　MPI-13

Name: 67-6668-82 Polyimide Heater Samicon MPI Type 25.4 x 76.2 mm 28 V 15 W MPI-13
Price: 397.69 USD

Check the Series Lineup

Products Information

Features

[High heat resistance] High heat resistance special polyimide film is used for the insulation that holds the heating wire, so it is a heater that can be used up to 200°C normally.
[Uniform temperature distribution] Since foil-shaped heating lines are evenly arranged on the heater surface and the heating area occupies a large portion of the heater surface area, it is a heater with low heating unevenness and high thermal efficiency.
[Environmentally Friendly] This is an eco-friendly heater that uses the characteristics of a thin heater to develop a terminal structure that does not use solder to connect the lead wire to the terminal.
[Low Outgassing] Since no adhesive is used for bonding insulators, this heater generates very little outgassing. In addition, since siloxane gas is not generated, it can be used in environments where the generation of siloxane gas is disliked.
[Fast Temperature Rising Response] Very thin insulator thickness of less than 0.2 mm and small heat capacity, this heater has especially fast temperature rising response of the heated object.

Spec

A(mm):25.4
B(mm):76.2
C(mm):200
Lead AWG: 26
Voltage (V): 28
Capacity (W): 15
Heater Surface Temperature: Normal 200°C (This is only a guide. The temperature that can be used may vary depending on the actual operating environment.)
Power density: (1) Suspended in still air: 1.0w/cm2 max. (2) Adhered to object to be heated: 1.5w/cm2 max.
Insulation resistance: 100 MΩ or more at 500 VDC mega
Thickness: 0.2 mm or less (excluding lead connection)
Precautions for Use
Do not use the product at a temperature higher than the specification limit. Be sure to control the temperature and use it at an appropriate temperature.
Do not repair, modify or disassemble the product by yourself.
Do not use in corrosive or high humidity environments.
Do not forcibly bend or pull the lead wire.
Do not bend the heater.
If there are any abnormalities such as smoke or strange smell, please stop using the heater immediately.
Store in a clean and dry place away from direct sunlight.
If the degree of adhesion to the object to be heated is low, an abnormally high temperature will occur, causing premature wire breakage.
Consult the manufacturer (Sakaguchi Electric Heating) when using by adhering to objects to be heated.
The joint of the lead wire is particularly vulnerable to external forces (Tension, bending, etc.).
Do not use multiple heaters.
WARNING: Mishandling of this product may cause electric shock, fire, or other accidents. Please observe the following precautions when using this product.
[Caution against ignition]
Never operate the product at a voltage higher than the rated voltage.
Do not use in flammable atmosphere as it is not explosion-proof.
Keep flammable materials away from the product.
[Electric shock caution]
Do not damage the heater surface and lead wires.
It's for indoor use only, and it's not waterproof. Do not let water, solution or steam come into contact with the heater.
[High temperature caution]
During or immediately after use, the heater and its peripherals are hot, so do not touch them until they have cooled sufficiently.

Order No.	67-6668-82
Model No.	MPI-13
Standard price	JPY: 63,400 USD: 397.69 Excange rate 1USD= 159.42JPY Valid price in Japan
Quantity	1sheet
Stock in Japan
Supplier Stock

Product Variations (Different Sizes, Specifications, Optional Products, etc.)

Order No.	Name	Model No.	Quantity	Standard price	Valid price in Japan
67-6668-80	Polyimide Heater Samicon MPI Type 25.4 x 25.4 mm 28 V 5 W　MPI-11	MPI-11	1sheet	JPY: 46,700	USD: 292.94
67-6668-81	Polyimide Heater Samicon MPI Type 25.4 x 50.8 mm 28 V 10 W　MPI-12	MPI-12	1sheet	JPY: 55,000	USD: 345.00
67-6668-82	Polyimide Heater Samicon MPI Type 25.4 x 76.2 mm 28 V 15 W　MPI-13	MPI-13	1sheet	JPY: 63,400	USD: 397.69