67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20
Features
- It is a suction type oxygen meter to measure the oxygen concentration in the furnace.
- MG6000 is an oximeter with a built-in suction pump.
- Measurement gas at high or low temperature in places where oxygen meters or oxygen sensors cannot be directly attached can be sucked by a pipe and measured at around normal temperature.
- Low concentration measurement gas can be sucked to measure oxygen concentration in a furnace or equipment at a distance.
- Measurement of hot or cold gases
- Since a suction pump and a flowmeter are built in, measuring gas can be radiated in the middle of pipes and piping and connected to an oxygen meter at around normal temperature.
- Since a filter containing activated carbon is built in, trace amounts of toxic gas and dust can be removed by the filter.
- An optional filter unit containing activated carbon can be added depending on the operating environment.
- high precision
- It has a high accuracy of ±0.5%O2, and the calibration gas connection port is provided in the body to facilitate calibration with reference gas and maintain accuracy.
- Excellent stability and long life
- It uses a high-performance compact zirconia solid electrolyte oxygen sensor that has a long life and is easy to maintain, so the accuracy is stable for a long time.
- Small and thin for easy operation
- Both the filter unit and the measuring unit are small and thin and easy to install.
- zirconia oximeter
- Stabilized zirconia is known as an oxygen ion conductor.
- The stabilized zirconia is used as a substrate, and a platinum electrode and an oxygen diffusion limiting hole are formed on one surface of the substrate, and a platinum heater is formed on the other surface.
- In order to obtain practical oxygen ion conductivity, the substrate is heated to several hundred °C by energizing the heater. When a voltage is applied between the electrodes, a current with oxygen ions as carriers flows through the substrate.
- Due to the oxygen diffusion limiting hole formed on the cathode, the amount of oxygen flowing into the cathode is limited, and a flat region (limit current) is observed in the current-voltage characteristics.
- Since the limiting current varies in proportion to the oxygen concentration, it is possible to determine the oxygen concentration in the atmosphere by measuring the limiting current.
SpecSpec class="init">
67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20 【AXEL GLOBAL】<!--@[ss-27]@--> アズワン<!--@/[ss-27]@-->
Contact us
CHINO CORPORATION
67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20
特徴
- It is a suction type oxygen meter to measure the oxygen concentration in the furnace.
- MG6000 is an oximeter with a built-in suction pump.
- Measurement gas at high or low temperature in places where oxygen meters or oxygen sensors cannot be directly attached can be sucked by a pipe and measured at around normal temperature.
- Low concentration measurement gas can be sucked to measure oxygen concentration in a furnace or equipment at a distance.
- Measurement of hot or cold gases
- Since a suction pump and a flowmeter are built in, measuring gas can be radiated in the middle of pipes and piping and connected to an oxygen meter at around normal temperature.
- Since a filter containing activated carbon is built in, trace amounts of toxic gas and dust can be removed by the filter.
- An optional filter unit containing activated carbon can be added depending on the operating environment.
- high precision
- It has a high accuracy of ±0.5%O2, and the calibration gas connection port is provided in the body to facilitate calibration with reference gas and maintain accuracy.
- Excellent stability and long life
- It uses a high-performance compact zirconia solid electrolyte oxygen sensor that has a long life and is easy to maintain, so the accuracy is stable for a long time.
- Small and thin for easy operation
- Both the filter unit and the measuring unit are small and thin and easy to install.
- zirconia oximeter
- Stabilized zirconia is known as an oxygen ion conductor.
- The stabilized zirconia is used as a substrate, and a platinum electrode and an oxygen diffusion limiting hole are formed on one surface of the substrate, and a platinum heater is formed on the other surface.
- In order to obtain practical oxygen ion conductivity, the substrate is heated to several hundred °C by energizing the heater. When a voltage is applied between the electrodes, a current with oxygen ions as carriers flows through the substrate.
- Due to the oxygen diffusion limiting hole formed on the cathode, the amount of oxygen flowing into the cathode is limited, and a flat region (limit current) is observed in the current-voltage characteristics.
- Since the limiting current varies in proportion to the oxygen concentration, it is possible to determine the oxygen concentration in the atmosphere by measuring the limiting current.
仕様
- Transmission signal output: 0~250 mV
- alarm setting
- Densitometer Mode Type I (optional by user)
- Initial value 18% lower limit, 26% upper limit, buzzer, lamp, relay output enabled, output held
- Display range: 0.0~25.0%O2/0.00~2.50%O2
- Transmission output range: output corresponding to 0.0~25.0%O2
- Measurement Principle: Zirconia Solid Electrolyte Method
- Air sampling method: suction pump type
- Response time: 90% Response within 1 minute
- Measurement value display: Digital display with 3-digit yellow-green LED
- Measurement Range (Resolution): 0.00~2.50 (0.01)/2.0~25.0 (0.1)%O2 (Automatic Range Switching)
- accuracy rating
- For 0.0~25.0%O2 ...±0.5%O2±1digit
- For 0.00~2.50%O2 ... +/- 0.05%O2 +/- 1digit (in a dry gas of oxygen and nitrogen)
- Transmission method: 0~100% of output doublet for 0.00~2.50 and 8~100% of output quad for 2.0~25.0
- Alarm function: Measured value alarm ...
- Alarm setting code: Densitometer mode *1
- *1 Alarm setting "A" is set to the initial value at the time of shipment, and alarm setting "B" is set to the state of alarm setting "0" for unspecified alarm value and alarm output operation.
- Lower warning value: within 0~26% Optional *2
- Upper warning value: within 0~26% Optional *2
- *2 The lower alarm value cannot be set to a value larger than the upper alarm value or cannot be specified. When alarm release alarm is held, it is released by front reset key.
- Relay output ON/OFF: Optional setting
- Buzzer Blow On/Off: Optional
- Lamp ON/OFF: Optional setting
- With/without output holding: Optional setting
- Detection element abnormality alarm: When the heater current to the oxygen detection element is abnormal, relay output is ON, buzzer is blown, and lamp is lit regardless of the content of the measured value alarm.
- Power failure warning: When the power supply to the tester is OFF or when the fuse is broken, relay output is ON.
- Alarm relay output: number of output circuits (1), output capacity (Resistive Load 110 V AC 0.2 A, 24 V DC 1 A/Inductive Load 110 V AC 0.1 A, 24 V DC 0.5 A)
- Warm-up time: 5 minutes
- Note)Warning signal is OFF and transmission signal is not output during warm-up.
- Operating Temperature Range: 0~40°C
- Operating humidity range: 80%rh or less
- Power: 100 VAC 50/60Hz
- Power Consumption: Approx. 13VA
- Mass: Approx. 4.6 kg
- Mounting Method: Body Bolt Mounting
- ISO 14001 Certified JQA-EM2414
- ISO 9001 Certification JQA-0656
- External Dimensions (Excluding Protrusions)
-
Package sizePackage sizes="init">
67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20 【AXEL GLOBAL】ASONE
Contact us
CHINO CORPORATION
67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20
Features
- It is a suction type oxygen meter to measure the oxygen concentration in the furnace.
- MG6000 is an oximeter with a built-in suction pump.
- Measurement gas at high or low temperature in places where oxygen meters or oxygen sensors cannot be directly attached can be sucked by a pipe and measured at around normal temperature.
- Low concentration measurement gas can be sucked to measure oxygen concentration in a furnace or equipment at a distance.
- Measurement of hot or cold gases
- Since a suction pump and a flowmeter are built in, measuring gas can be radiated in the middle of pipes and piping and connected to an oxygen meter at around normal temperature.
- Since a filter containing activated carbon is built in, trace amounts of toxic gas and dust can be removed by the filter.
- An optional filter unit containing activated carbon can be added depending on the operating environment.
- high precision
- It has a high accuracy of ±0.5%O2, and the calibration gas connection port is provided in the body to facilitate calibration with reference gas and maintain accuracy.
- Excellent stability and long life
- It uses a high-performance compact zirconia solid electrolyte oxygen sensor that has a long life and is easy to maintain, so the accuracy is stable for a long time.
- Small and thin for easy operation
- Both the filter unit and the measuring unit are small and thin and easy to install.
- zirconia oximeter
- Stabilized zirconia is known as an oxygen ion conductor.
- The stabilized zirconia is used as a substrate, and a platinum electrode and an oxygen diffusion limiting hole are formed on one surface of the substrate, and a platinum heater is formed on the other surface.
- In order to obtain practical oxygen ion conductivity, the substrate is heated to several hundred °C by energizing the heater. When a voltage is applied between the electrodes, a current with oxygen ions as carriers flows through the substrate.
- Due to the oxygen diffusion limiting hole formed on the cathode, the amount of oxygen flowing into the cathode is limited, and a flat region (limit current) is observed in the current-voltage characteristics.
- Since the limiting current varies in proportion to the oxygen concentration, it is possible to determine the oxygen concentration in the atmosphere by measuring the limiting current.
Spec
- Transmission signal output: 0~250 mV
- alarm setting
- Densitometer Mode Type I (optional by user)
- Initial value 18% lower limit, 26% upper limit, buzzer, lamp, relay output enabled, output held
- Display range: 0.0~25.0%O2/0.00~2.50%O2
- Transmission output range: output corresponding to 0.0~25.0%O2
- Measurement Principle: Zirconia Solid Electrolyte Method
- Air sampling method: suction pump type
- Response time: 90% Response within 1 minute
- Measurement value display: Digital display with 3-digit yellow-green LED
- Measurement Range (Resolution): 0.00~2.50 (0.01)/2.0~25.0 (0.1)%O2 (Automatic Range Switching)
- accuracy rating
- For 0.0~25.0%O2 ...±0.5%O2±1digit
- For 0.00~2.50%O2 ... +/- 0.05%O2 +/- 1digit (in a dry gas of oxygen and nitrogen)
- Transmission method: 0~100% of output doublet for 0.00~2.50 and 8~100% of output quad for 2.0~25.0
- Alarm function: Measured value alarm ...
- Alarm setting code: Densitometer mode *1
- *1 Alarm setting "A" is set to the initial value at the time of shipment, and alarm setting "B" is set to the state of alarm setting "0" for unspecified alarm value and alarm output operation.
- Lower warning value: within 0~26% Optional *2
- Upper warning value: within 0~26% Optional *2
- *2 The lower alarm value cannot be set to a value larger than the upper alarm value or cannot be specified. When alarm release alarm is held, it is released by front reset key.
- Relay output ON/OFF: Optional setting
- Buzzer Blow On/Off: Optional
- Lamp ON/OFF: Optional setting
- With/without output holding: Optional setting
- Detection element abnormality alarm: When the heater current to the oxygen detection element is abnormal, relay output is ON, buzzer is blown, and lamp is lit regardless of the content of the measured value alarm.
- Power failure warning: When the power supply to the tester is OFF or when the fuse is broken, relay output is ON.
- Alarm relay output: number of output circuits (1), output capacity (Resistive Load 110 V AC 0.2 A, 24 V DC 1 A/Inductive Load 110 V AC 0.1 A, 24 V DC 0.5 A)
- Warm-up time: 5 minutes
- Note)Warning signal is OFF and transmission signal is not output during warm-up.
- Operating Temperature Range: 0~40°C
- Operating humidity range: 80%rh or less
- Power: 100 VAC 50/60Hz
- Power Consumption: Approx. 13VA
- Mass: Approx. 4.6 kg
- Mounting Method: Body Bolt Mounting
- ISO 14001 Certified JQA-EM2414
- ISO 9001 Certification JQA-0656
- External Dimensions (Excluding Protrusions)
-
Package size：250×105×250 mm 4.6 kg
[About Package size]
Order No.
67-4915-88
Model No.
MG6000-A20
JAN Code
4562208231748
Standard price
JPY: 444,000
USD: 2,783.18
Excange rate 1USD= 159.53JPY
Valid price in Japan
Quantity
1piece
Stock in Japan
Supplier Stock
Product Variations (Different Sizes, Specifications, Optional Products, etc.)
Product image
Order No.
Name
Model No.
Quantity
Standard price
Valid price in Japan
Stock
[Supplier Stock]
67-4915-84
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Acidity Meter Mode I, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-000
MG6000-000
1piece
JPY: 428,000
USD: 2,682.88
67-4915-85
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Acidity Meter Mode Ii, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-100
MG6000-100
1piece
JPY: 431,000
USD: 2,701.69
67-4915-86
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-A00
MG6000-A00
1piece
JPY: 431,000
USD: 2,701.69
67-4915-87
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.00~2.50%O2 Fixed, Transmission Output: Supports 0.00~2.50%O2) MG6000-A11
MG6000-A11
1piece
JPY: 447,000
USD: 2,801.98
67-4915-88
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20
MG6000-A20
1piece
JPY: 444,000
USD: 2,783.18
67-4915-89
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~250%O2/0.00~2.50%O2, Display: 000~250) MG6000-A22
MG6000-A22
1piece
JPY: 447,000
USD: 2,801.98
67-4915-90
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-B00
MG6000-B00
1piece
JPY: 436,000
USD: 2,733.03
67-4915-91
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Display: 0.00~2.50%O2 Fixed, Transmission Output: Supports 0.00~2.50%O2) MG6000-B11
MG6000-B11
1piece
JPY: 452,000
USD: 2,833.32
67-4915-92
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Indication: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-B20
MG6000-B20
1piece
JPY: 449,000
USD: 2,814.52
67-4915-93
Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Display: 0.0~25.0%O2/0.00~2.50%O2, Display: 000~250) MG6000-B22
MG6000-B22
1piece
JPY: 452,000
USD: 2,833.32
Related Products
67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20
特徴
- It is a suction type oxygen meter to measure the oxygen concentration in the furnace.
- MG6000 is an oximeter with a built-in suction pump.
- Measurement gas at high or low temperature in places where oxygen meters or oxygen sensors cannot be directly attached can be sucked by a pipe and measured at around normal temperature.
- Low concentration measurement gas can be sucked to measure oxygen concentration in a furnace or equipment at a distance.
- Measurement of hot or cold gases
- Since a suction pump and a flowmeter are built in, measuring gas can be radiated in the middle of pipes and piping and connected to an oxygen meter at around normal temperature.
- Since a filter containing activated carbon is built in, trace amounts of toxic gas and dust can be removed by the filter.
- An optional filter unit containing activated carbon can be added depending on the operating environment.
- high precision
- It has a high accuracy of ±0.5%O2, and the calibration gas connection port is provided in the body to facilitate calibration with reference gas and maintain accuracy.
- Excellent stability and long life
- It uses a high-performance compact zirconia solid electrolyte oxygen sensor that has a long life and is easy to maintain, so the accuracy is stable for a long time.
- Small and thin for easy operation
- Both the filter unit and the measuring unit are small and thin and easy to install.
- zirconia oximeter
- Stabilized zirconia is known as an oxygen ion conductor.
- The stabilized zirconia is used as a substrate, and a platinum electrode and an oxygen diffusion limiting hole are formed on one surface of the substrate, and a platinum heater is formed on the other surface.
- In order to obtain practical oxygen ion conductivity, the substrate is heated to several hundred °C by energizing the heater. When a voltage is applied between the electrodes, a current with oxygen ions as carriers flows through the substrate.
- Due to the oxygen diffusion limiting hole formed on the cathode, the amount of oxygen flowing into the cathode is limited, and a flat region (limit current) is observed in the current-voltage characteristics.
- Since the limiting current varies in proportion to the oxygen concentration, it is possible to determine the oxygen concentration in the atmosphere by measuring the limiting current.
仕様
- Transmission signal output: 0~250 mV
- alarm setting
- Densitometer Mode Type I (optional by user)
- Initial value 18% lower limit, 26% upper limit, buzzer, lamp, relay output enabled, output held
- Display range: 0.0~25.0%O2/0.00~2.50%O2
- Transmission output range: output corresponding to 0.0~25.0%O2
- Measurement Principle: Zirconia Solid Electrolyte Method
- Air sampling method: suction pump type
- Response time: 90% Response within 1 minute
- Measurement value display: Digital display with 3-digit yellow-green LED
- Measurement Range (Resolution): 0.00~2.50 (0.01)/2.0~25.0 (0.1)%O2 (Automatic Range Switching)
- accuracy rating
- For 0.0~25.0%O2 ...±0.5%O2±1digit
- For 0.00~2.50%O2 ... +/- 0.05%O2 +/- 1digit (in a dry gas of oxygen and nitrogen)
- Transmission method: 0~100% of output doublet for 0.00~2.50 and 8~100% of output quad for 2.0~25.0
- Alarm function: Measured value alarm ...
- Alarm setting code: Densitometer mode *1
- *1 Alarm setting "A" is set to the initial value at the time of shipment, and alarm setting "B" is set to the state of alarm setting "0" for unspecified alarm value and alarm output operation.
- Lower warning value: within 0~26% Optional *2
- Upper warning value: within 0~26% Optional *2
- *2 The lower alarm value cannot be set to a value larger than the upper alarm value or cannot be specified. When alarm release alarm is held, it is released by front reset key.
- Relay output ON/OFF: Optional setting
- Buzzer Blow On/Off: Optional
- Lamp ON/OFF: Optional setting
- With/without output holding: Optional setting
- Detection element abnormality alarm: When the heater current to the oxygen detection element is abnormal, relay output is ON, buzzer is blown, and lamp is lit regardless of the content of the measured value alarm.
- Power failure warning: When the power supply to the tester is OFF or when the fuse is broken, relay output is ON.
- Alarm relay output: number of output circuits (1), output capacity (Resistive Load 110 V AC 0.2 A, 24 V DC 1 A/Inductive Load 110 V AC 0.1 A, 24 V DC 0.5 A)
- Warm-up time: 5 minutes
- Note)Warning signal is OFF and transmission signal is not output during warm-up.
- Operating Temperature Range: 0~40°C
- Operating humidity range: 80%rh or less
- Power: 100 VAC 50/60Hz
- Power Consumption: Approx. 13VA
- Mass: Approx. 4.6 kg
- Mounting Method: Body Bolt Mounting
- ISO 14001 Certified JQA-EM2414
- ISO 9001 Certification JQA-0656
- External Dimensions (Excluding Protrusions)
Package sizePackage sizes="init">
67-4915-88 Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20
Features
- It is a suction type oxygen meter to measure the oxygen concentration in the furnace.
- MG6000 is an oximeter with a built-in suction pump.
- Measurement gas at high or low temperature in places where oxygen meters or oxygen sensors cannot be directly attached can be sucked by a pipe and measured at around normal temperature.
- Low concentration measurement gas can be sucked to measure oxygen concentration in a furnace or equipment at a distance.
- Measurement of hot or cold gases
- Since a suction pump and a flowmeter are built in, measuring gas can be radiated in the middle of pipes and piping and connected to an oxygen meter at around normal temperature.
- Since a filter containing activated carbon is built in, trace amounts of toxic gas and dust can be removed by the filter.
- An optional filter unit containing activated carbon can be added depending on the operating environment.
- high precision
- It has a high accuracy of ±0.5%O2, and the calibration gas connection port is provided in the body to facilitate calibration with reference gas and maintain accuracy.
- Excellent stability and long life
- It uses a high-performance compact zirconia solid electrolyte oxygen sensor that has a long life and is easy to maintain, so the accuracy is stable for a long time.
- Small and thin for easy operation
- Both the filter unit and the measuring unit are small and thin and easy to install.
- zirconia oximeter
- Stabilized zirconia is known as an oxygen ion conductor.
- The stabilized zirconia is used as a substrate, and a platinum electrode and an oxygen diffusion limiting hole are formed on one surface of the substrate, and a platinum heater is formed on the other surface.
- In order to obtain practical oxygen ion conductivity, the substrate is heated to several hundred °C by energizing the heater. When a voltage is applied between the electrodes, a current with oxygen ions as carriers flows through the substrate.
- Due to the oxygen diffusion limiting hole formed on the cathode, the amount of oxygen flowing into the cathode is limited, and a flat region (limit current) is observed in the current-voltage characteristics.
- Since the limiting current varies in proportion to the oxygen concentration, it is possible to determine the oxygen concentration in the atmosphere by measuring the limiting current.
Spec
- Transmission signal output: 0~250 mV
- alarm setting
- Densitometer Mode Type I (optional by user)
- Initial value 18% lower limit, 26% upper limit, buzzer, lamp, relay output enabled, output held
- Display range: 0.0~25.0%O2/0.00~2.50%O2
- Transmission output range: output corresponding to 0.0~25.0%O2
- Measurement Principle: Zirconia Solid Electrolyte Method
- Air sampling method: suction pump type
- Response time: 90% Response within 1 minute
- Measurement value display: Digital display with 3-digit yellow-green LED
- Measurement Range (Resolution): 0.00~2.50 (0.01)/2.0~25.0 (0.1)%O2 (Automatic Range Switching)
- accuracy rating
- For 0.0~25.0%O2 ...±0.5%O2±1digit
- For 0.00~2.50%O2 ... +/- 0.05%O2 +/- 1digit (in a dry gas of oxygen and nitrogen)
- Transmission method: 0~100% of output doublet for 0.00~2.50 and 8~100% of output quad for 2.0~25.0
- Alarm function: Measured value alarm ...
- Alarm setting code: Densitometer mode *1
- *1 Alarm setting "A" is set to the initial value at the time of shipment, and alarm setting "B" is set to the state of alarm setting "0" for unspecified alarm value and alarm output operation.
- Lower warning value: within 0~26% Optional *2
- Upper warning value: within 0~26% Optional *2
- *2 The lower alarm value cannot be set to a value larger than the upper alarm value or cannot be specified. When alarm release alarm is held, it is released by front reset key.
- Relay output ON/OFF: Optional setting
- Buzzer Blow On/Off: Optional
- Lamp ON/OFF: Optional setting
- With/without output holding: Optional setting
- Detection element abnormality alarm: When the heater current to the oxygen detection element is abnormal, relay output is ON, buzzer is blown, and lamp is lit regardless of the content of the measured value alarm.
- Power failure warning: When the power supply to the tester is OFF or when the fuse is broken, relay output is ON.
- Alarm relay output: number of output circuits (1), output capacity (Resistive Load 110 V AC 0.2 A, 24 V DC 1 A/Inductive Load 110 V AC 0.1 A, 24 V DC 0.5 A)
- Warm-up time: 5 minutes
- Note)Warning signal is OFF and transmission signal is not output during warm-up.
- Operating Temperature Range: 0~40°C
- Operating humidity range: 80%rh or less
- Power: 100 VAC 50/60Hz
- Power Consumption: Approx. 13VA
- Mass: Approx. 4.6 kg
- Mounting Method: Body Bolt Mounting
- ISO 14001 Certified JQA-EM2414
- ISO 9001 Certification JQA-0656
- External Dimensions (Excluding Protrusions)
Package size：250×105×250 mm 4.6 kg [About Package size]
| Order No. | 67-4915-88 | |
|---|---|---|
| Model No. | MG6000-A20 | |
| JAN Code | 4562208231748 | |
| Standard price |
JPY: 444,000
USD: 2,783.18
Excange rate 1USD= 159.53JPY
Valid price in Japan |
|
| Quantity | 1piece | |
| Stock in Japan |
|
|
| Supplier Stock |
|
|
Product Variations (Different Sizes, Specifications, Optional Products, etc.)
| Product image | Order No. | Name | Model No. | Quantity | Standard price | Valid price in Japan | Stock [Supplier Stock] |
|
|---|---|---|---|---|---|---|---|---|
|
67-4915-84 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Acidity Meter Mode I, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-000 | MG6000-000 | 1piece | JPY: 428,000 | USD: 2,682.88 |
|
|
|
67-4915-85 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Acidity Meter Mode Ii, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-100 | MG6000-100 | 1piece | JPY: 431,000 | USD: 2,701.69 |
|
|
|
67-4915-86 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-A00 | MG6000-A00 | 1piece | JPY: 431,000 | USD: 2,701.69 |
|
|
|
67-4915-87 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.00~2.50%O2 Fixed, Transmission Output: Supports 0.00~2.50%O2) MG6000-A11 | MG6000-A11 | 1piece | JPY: 447,000 | USD: 2,801.98 |
|
|
|
67-4915-88 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-A20 | MG6000-A20 | 1piece | JPY: 444,000 | USD: 2,783.18 |
|
|
|
67-4915-89 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode I, Display: 0.0~250%O2/0.00~2.50%O2, Display: 000~250) MG6000-A22 | MG6000-A22 | 1piece | JPY: 447,000 | USD: 2,801.98 |
|
|
|
67-4915-90 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Display: 0.0~25.0%O2 Fixed, Transmission Output: Supports 0.0~25.0%O2) MG6000-B00 | MG6000-B00 | 1piece | JPY: 436,000 | USD: 2,733.03 |
|
|
|
67-4915-91 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Display: 0.00~2.50%O2 Fixed, Transmission Output: Supports 0.00~2.50%O2) MG6000-B11 | MG6000-B11 | 1piece | JPY: 452,000 | USD: 2,833.32 |
|
|
|
67-4915-92 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Indication: 0.0~25.0%O2/0.00~2.50%O2, Transmission Output: 0.0~25.0%O2) MG6000-B20 | MG6000-B20 | 1piece | JPY: 449,000 | USD: 2,814.52 |
|
|
|
67-4915-93 | Mg6000Series Wall-Mounted Suction Type Oxygen Meter (Transmission: 0~250 Mv, Densitometer Mode Ii, Display: 0.0~25.0%O2/0.00~2.50%O2, Display: 000~250) MG6000-B22 | MG6000-B22 | 1piece | JPY: 452,000 | USD: 2,833.32 |
|
