67-4915-70 Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Densitometer Mode Ii, Display: 0.0~25.0%O2) MG3010-B0
Features
- It receives the output from the oxygen sensor or oxygen meter and gives instructions and alarm.
- The MG3010 is a dedicated measurement monitor that receives the transmission output signal from the MG1000 series oxygen meter and the MG2100 oxygen sensor at a remote location, and can confirm the measured value and determine the alarm.
- Equipped with DC voltage output function for MG2100 drive, it can measure and monitor oxygen concentration in the field without power supply.
Spec
- Received Signal: 0~250 mV DC
- alarm setting
- Densitometer Mode Type II (fixed by user)
- Lower limit value, Upper limit value, buzzer enabled/disabled, lamp enabled/disabled, relay output enabled/disabled, output holding enabled/disabled
- Unspecified parameters are the default values for densitometer mode Type I.
- Display range: 0.0~25.0%O2
- Measurement value display: Digital display with 3-digit yellow-green LED
- Display range (resolution): 0.0~25.0 (0.1)%O2
- Accuracy rating: ±0.3%O2±1digit
- DC voltage output
- Used as a power supply for MG2100
- Output voltage: 5 V±0.5 V DC
- Connected Model: 1 MG2100 or MG1000 Series
- Alarm function: Measured value alarm ...
- Alarm setting code: Densitometer mode *1
- *1 Alarm setting "A" is set to the initial value at the time of shipment, and alarm setting "B" is set to the state of alarm setting "0" for unspecified alarm value and alarm output operation.
- Lower warning value: specified within 0~26% *2
- Upper warning value: specified within 0~26% *2
- *2 The lower alarm value cannot be set to a value larger than the upper alarm value or cannot be specified. When alarm release alarm is held, it is released by front reset key.
- Relay output yes/no: Optional
- Buzzer with/without: Optional
- Lamp ON/OFF: Optional
- Output Hold Yes/No: Optional
- Power failure warning: When the power supply to the tester is OFF or when the fuse is broken, relay output is ON.
- Alarm relay output: number of output circuits (2), output capacity (Resistive Load 110 V AC 0.2 A, 24 V DC 1 A/Inductive Load 110 V AC 0.1 A, 24 V DC 0.5 A)
- Warm-up time: 5 minutes
- Note)Alarm signal OFF during warm-up
- Operating Temperature Range: 0~40°C
- Operating humidity range: 80%rh or less
- Power: 100 VAC ±10% 50/60Hz
- Power Consumption
- Approx. 5VA for the main body only (when DC voltage output is unloaded)
- Approx. 8.5VA when used in combination with MG2100 series
- Weight: about 500 g
- Mounting method: wall or switchbox mounting
- ISO 14001 Certified JQA-EM2414
- ISO 9001 Certification JQA-0656
Package size：120×55×120 mm 500 g [About Package size]
| Order No. | 67-4915-70 | |
|---|---|---|
| Model No. | MG3010-B0 | |
| JAN Code | 4562208231564 | |
| Standard price |
JPY: 80,000
USD: 501.47
Excange rate 1USD= 159.53JPY
Valid price in Japan |
|
| Quantity | 1piece | |
| Stock in Japan |
|
|
| Supplier Stock |
|
|
Product Variations (Different Sizes, Specifications, Optional Products, etc.)
| Product image | Order No. | Name | Model No. | Quantity | Standard price | Valid price in Japan | Stock [Supplier Stock] |
|
|---|---|---|---|---|---|---|---|---|
 |
67-4915-66 | Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Anoxic Meter Mode I, Indication: 0.0~25.0%O2) MG3010-00 | MG3010-00 | 1piece | JPY: 72,000 | USD: 451.33 |
|
|
 |
67-4915-67 | Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Anoxic Meter Mode Ii, Indication: 0.0~25.0%O2) MG3010-10 | MG3010-10 | 1piece | JPY: 75,000 | USD: 470.13 |
|
|
 |
67-4915-68 | Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Densitometer Mode I, Display: 0.0~25.0%O2) MG3010-A0 | MG3010-A0 | 1piece | JPY: 75,000 | USD: 470.13 |
|
|
 |
67-4915-69 | Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Densitometer Mode I, Display: 0.00~2.50%O2) MG3010-A1 | MG3010-A1 | 1piece | JPY: 78,000 | USD: 488.94 |
|
|
 |
67-4915-70 | Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Densitometer Mode Ii, Display: 0.0~25.0%O2) MG3010-B0 | MG3010-B0 | 1piece | JPY: 80,000 | USD: 501.47 |
|
|
 |
67-4915-71 | Mg3010Series 1 Point Measurement Monitor (Reception: 0~250 Mv, Densitometer Mode Ii, Display: 0.00~2.50%O2) MG3010-B1 | MG3010-B1 | 1piece | JPY: 83,000 | USD: 520.28 |
|
