Features

• Supports Ethernet connectivity
• Wide Area Monitoring Using Ethernet Environments
• By combining Ethernet connection with specified low power radio, it is possible to easily manage data collected over a wide area, which was difficult by radio communication alone.
• Integrated management of 6 receivers on a PC
• Up to 6 receivers can be connected on the Ethernet, and each receiver can collect and monitor data from 60 transmitters.
• Mail report by receiver alone
• Each transmitter performs measurement and monitoring even when the application software is not running.
• When the alarm is judged, contact output (3 points) and mail report are performed from the receiver body. You can register 5 recipients, and you can set a mail report recipient for each sender. You can also send a test mail by pressing the front key.
• Build large systems intuitively
• Easy build on PC
• You can tentatively decide the system at hand and adjust it after installation on the computer. You can easily change the signal path by simply dragging with the mouse.
• *You can change the communication route without depending on the registered receiver.
• 6 relay stages per receiver, 60 transmitters can be connected
• The transmitter is equipped with a relay function so that it can also serve as a relay while measuring data. A maximum of 6 relay stages and 60 transmitters can be connected per receiver.
• Easily add and delete receivers and transmitters
• You can easily register the receiver in the application software. The transmitter is connected directly under the receiver that performed the registration operation.
• Registered receivers and transmitters can be checked in the application software, and can be easily added or deleted from the system.
• Effective data management
• trend graph
• The collected data is stored in a database inside the PC and can be used for trend graphs, etc. A trend graph can display up to six transmitters on the same graph regardless of the recording interval. You can also perform screen operations such as enlarging the displayed trend graph and scrolling left and right. You can also display documents in conjunction with the trend graph.
• Time correction possible
• Synchronizes the time between the computer and all receivers/transmitters to prevent time swings throughout the system. Time synchronization by the receiver alone using SNTP is also possible.
• transmitter survival confirmation function
• An alarm is output when radio communication fails continuously to the same transmitter *. This helps to reduce system failures by detecting system abnormalities at an early stage. *Exclude alarm communication
• List screen
• You can automatically update the latest data of any transmitter, the radio wave strength during radio communication, the remaining battery level of each device, and the alarm status display according to the set period.
• Scaling capability (Voltage input models only)
• Since the display of the main body can also be displayed in the scale value, it is easy to confirm the instruction in the field.
• Voltage value and scaling value can each store 16000 data, and alarm monitoring can be performed individually.
• Meet a wide range of monitoring needs
• Centralized monitoring of multiple departments
• You can manage up to 12 groups of 360 transmitters. By grouping, you can manage the display of list screens and email reports by group, so that you can quickly check the recorded data of the department in charge when monitoring across multiple departments.
• Various alarm judgment functions
• Achieves highly reliable measurement
• Possible input of temperature measuring resistor and thermocouple
• Based on the know-how accumulated over many years, Chino proposes temperature sensors suitable for the purpose of use.
• 16000 data is stored in the transmitter
• A large memory capacity of up to 16000 data * is installed on the transmitter side to prevent data loss due to unforeseen circumstances.
• Even if the battery runs out, the data stored in the transmitter is retained.
• *The temperature and humidity sensor model can store 16000 data each for temperature and humidity.
• The voltage input model can store 16000 data each of voltage value and scaling conversion value.
• Standard attached inspection report
• A test report is included with the purchase of the transmitter. We can also issue a traceability certificate (sold separately). The JCSS certified traceability system is a proof of trust.
• The temperature and humidity high-precision model replacement sensor can be issued as a single unit.
• Replacement sensors for high-precision models of temperature and humidity can be used independently to issue certificates of performance and traceability, helping to save labor and reduce costs in on-site calibration.
• Part11 compatible software available
• The MD8000 Series Application Soft Ethernet Edition with Security Functions meets the requirements of FDA 21 CFR Part11 and ER/ES guidelines for data collection and monitoring in pharmaceutical manufacturing, medical vaults, etc. Chino also prepares templates for installation qualification (IQ) and operational qualification (OQ) in accordance with the CSV "Computerized System Validation" in the Proper Management Guidelines.
• *For wireless data collection, MD800R-00L (receiver) and application software are required.
• When the temperature/humidity sensor is used for a long time in a high temperature/humidity environment, the indication value may gradually change due to the characteristics of the humidity element.
• Do not use the temperature/humidity sensor in the following locations.
• Places where dust or dust is scattered, places where ketone organic agents/ester organic agents/halogens/oil mist/salt is high, places where explosive gases/corrosive gases are present, places where steam/chemicals/sea water is exposed, places where direct sunlight is exposed, places where ultraviolet rays are exposed, places where paint is dried, etc.