AS ONE AS ONE

Listed products : 3 milion products
How to use
Cách sử dụng
Contact us
All Categories
[Discontinued]Controller for Optmike Control Axis 2 Axis OMEC-2BG 61-6982-55 【AXEL GLOBAL】<!--@[ss-27]@--> アズワン<!--@/[ss-27]@-->

AS ONE AS ONE

取扱点数300万点
How to use
Cách sử dụng
Contact us
すべてのカテゴリ
Contact us
Quote Other Requests
  • AXEL GLOBAL
  • カテゴリ一覧
  • Lab Instruments & Supplies
  • Analyzer, Testing Equipment
  • Laser & Optical Equipment, Parts
  • Actuator of Laser Equipment
  • [Discontinued]Controller for Optmike Control Axis 2 Axis and others
  • 61-6982-55 [Discontinued]Controller for Optmike Control Axis 2 Axis OMEC-2BG
SIGMAKOKI CO., LTD.

61-6982-55 [Discontinued]Controller for Optmike Control Axis 2 Axis OMEC-2BG

  • Print
  • PDF
Check the Series Lineup
  • [Discontinued]Controller for Optmike Control Axis 2 Axis OMEC-2BG

Features

  • A dedicated controller for opto-microphone with encoder (SOM-C).
  • This controller has interfaces RS232C, GP-IB, and USB, and can be driven manually by automatic control from a PC or by switching the jog switch.
  • You can control complex behavior by sending simple commands from your PC through the interface.
  • A double loop with speed control and deviation counter is adopted as the positioning system, so stable and high-precision operation is possible.
  • * The USB interface only supports the company's software.
  • * Opt microphones or other products without encoders of the Company may not be used in this controller.
  • * Be aware that the connection will not operate properly and may cause malfunction.

Spec

  • [ Common specification]
  • Power voltage: AC100-120V/200-240V, 50/60Hz 20VA
  • Operation temperature: 5 - 40℃
  • Ambient humidity: 20 - 85% RH (non-condensing)
  • Storage temperature: ?20 - 60℃
  • Outer dimensions: (W) 200 x (H) 52 x (D) 172mm (excludes projecting parts)
  • Mass: 1.5kg
  • No. of control axes: 2 axes (2BG), 4 axes (4BG, However, simultaneous drive is up to 2 axes in the same group)
  • Coordinate setting range: ±32,767
  • Transfer rate: 1.5 - 100μm/sec
  • Transfer rate settings: 32 step
  • Pulse move distance: 1μm/pulse
  • Interface RS232C: Connector D-Sub 9pin Female connector Inch screw, Baud rate 4800/9600/19200/38400, 8 bits data length, No parity, Stop bit 1 bit, Delimiter CR + LF/CR/LFNo flow control
  • Interface GP-IB: Setting addresses 1 - 30, Delimiter CR + LF/CR/LF/EOI
  • Interface USB: Support Full Speed mode, Delimiter CR
  • Driver compatible motor: DC coreless servomotor
  • Driver overload detection (over current detection): Is available
  • Driver encoder signal: A and B phases, 1μm/pulse after multiplied by 2 on the driver side
  • Driver limit sensor: + side, ? side limit (Direction to draw in the spindle is "?")
  • Driver polarity: Normally closed
  • Command name/revert to the mechanical origin: Command H: Return to the mechanical origin
  • Command name/logical origin setting: Command R: Clear the current position coordinate
  • Command name/speed settings: Command D: Set up transfer rate
  • Command name/relative transfer drive: Command M: Relative position transfer drive
  • Command name/absolute transfer drive: Command A: Absolute position transfer drive
  • Command name/stop: Command L: Stop optmike transfer
  • Command name/logical origin return: Command N: Return to the logical origin
  • Command name/control commands: Command X: Lost motion settings
  • Command name/device state confirmation: Command Q: check optmike coordinate
  • Command name/controller state confirmation: Command ?: check controller state
  • [Individual specification]
  • No. of control axes: 2 axes
  •  
Order No. 61-6982-55
Model No. OMEC-2BG
標準価格 JPY: 185,000 USD: 1,159.66
Excange rate 1USD= 159.53JPY
Valid price in Japan
Quantity 1piece
  Discontinued
Stock in Japan -

商品のバリエーション (サイズ違い・スペック違い・オプション品など)

Product image アズワン品番 Name Model No. Quantity Standard price 標準価格(ドル) Stock
[Supplier Stock]
61-6982-55 [Discontinued]Controller for Optmike Control Axis 2 Axis OMEC-2BG OMEC-2BG 1piece JPY: 185,000 USD: 1,159.66

-

61-6982-56 [Discontinued]Controller for Optmike Control Axis 4 Axis OMEC-4BG OMEC-4BG 1piece JPY: 235,000 USD: 1,473.08

-

Related Products

1 / 1 ページ

[Discontinued]RS232C/Str-3 for Bios-Light RS232C/STR-3

[Discontinued]RS232C/Str-3 for Bios-Light RS232C/STR-3

This page is the page of [Discontinued]Controller for Optmike Control Axis 2 Axis sold by AS ONE CORPORATION. AXEL GLOBAL is a website that lists more than 3 million products that are used in a wide range of fields, including Research and Development, Production,Semiconductor, Medicine, Nursing care, and Food sanitation.

Explore AXEL

  • Categories
  • Catalogs
  • Brands

How to use

  • User’s Guide
  • For Re-seller
  • For End-User

Get to Know Us

  • About us
  • Site Policy
  • Privacy Policy
  • Cookies Policy

Let Us Help You

  • Contact Us
  • Product Proposal
    (for Supplier)
  • Other Requests

Countries and Regions

  • English

  • China

  • Indonesia

  • Korea

  • Thailand

  • Vietnam

AS ONE Group

  • AXEL-SHOP (Japan)

  • AS ONE INTERNATIONAL

  • AS ONE 亚速旺上海商贸 (China)

Copyright © AS ONE Corporation. All rights reserved.