[Unipower]Automation & Control Gear
Filters
-
Unipower 5 → 60 A Motor Load Transducer, 24 V dc APM10
APM10 - kW-Transmitter. The APM10 is a monitor- and protection unit for motors. The unit converts kW into an analogue process signal for use in PLC's and other controllers. Transmitter for kW, 3 phase symmetrical load For connecting to a 3 phase net of up to 3x500 Vac Internal Current Transformer Input Current Range 5, 10, 20, 25, 40, 60 Aac 24 V Power Supply Analogue output 0(4)-20mA or 0(2)-10V DIP switch settings for output signal Galvanic insulation between input and output Test Voltage 3 kV
1 products found
JPY: 72,800
USD: 456.34
-
Unipower 8 A Motor Load Monitor, 380 → 440 V HPL110
Digital Motor Load (kW) Monitors. Units which measure true motor load in kW featuring a digital display of kW% and programmable trips for over and/or under load events.These units protect equipment from damage caused by the motor running against a jam, blockage or under load and are also used in processes to trigger subsequent actions when predetermined load levels are reached (end point monitoring).The display is used as a reference enabling motor load, trip levels and all other variables to be displayed and programmed quickly and accurately using only three push buttons.The units are usually mounted in the motor control panel and are connected to a convenient point on the motor supply (before Inverter - if used).Therefore no external field wiring or sensors in the equipment are necessary. In addition to displaying motor power in real time the units capture and, on demand, display the instantaneous minimum and maximum power levels to assist in setting up and fault diagnosis.Three digital delay timers, programmable from 0.1-25 seconds are incorporated to time out motor start surge and short duration over and under power events which could cause nuisance tripping.A DIP switch is used to tamper proof all settings. The HPL110 and HPL110A can be switched to either 50 or 6necessary.In0Hz operation.Both units can be operated in manual or auto-reset modes. In auto-reset mode programmable hysteresis, which provides differential between trip and reset levels is automatically enabled.The HPL 110 is DIN rail mounting whilst the HPL110A can be panel mounted.Applications include the over/underload protection of:Pumps (dry run, closed valve), Fans (broken belt, closed damper), Conveyors (screw and belt),Separation screens, Macerators, scrapers, Mechanical drives (gearboxes, chains)
1 products found
JPY: 158,000
USD: 990.41
-
［Discontinued］Unipower 80 A Motor Load Monitor, 250 V ac APM110
APM110 - Analogue Motor Load Monitor. The APM110 is a monitor- and protection unit for motors. The unit measures kW used by a 3-phase motor to detect machine overload or under load. Commonly used to protect pumps, conveyors, macerators, scrapers and filtration screens. Supply and voltage range from 3x 380-500 Vac Programmable max. and min. kW limit detector plus the support functions Internal current transformer for currents up to 80A Power range max. 70 kW with internal current sensor Auto and manual reset DIN rail mounting
1 products found
JPY: 51,800
USD: 324.70
-
［Discontinued］Unipower 80 A Motor Load Monitor, 230 V ac APM110E
APM110E - Analogue Motor Load Monitor. The APM110E is a monitor- and protection unit for motors. The unit measures kW used by a 3-phase motor to detect machine overload or under load. Commonly used to protect pumps, conveyors, macerators, scrapers and filtration screens. Features output connections for the PCU D10, remote front panel display and control module. Supply voltage from 1x 120/230 Vac Voltage range from 3x 230-575 Vac Programmable max. and min. kW limit detector plus the support functions Internal current transformer for currents up to 80A Power range max. 80 kW with internal current sensor Auto and manual reset DIN rail mounting An external display (PCU D10; Stock-no.: ; 793-4111 793-4111 ) can be connect via 2-wire connection
1 products found
JPY: 83,300
USD: 522.16
