[Parallax Inc]Electronic/Electrical Parts and Controll Equipments
Filters
-
Parallax Inc 910-28015A, PING))) Ultrasonic Distance Sensor Development Kit 910-28015A
Standard servo motor, servo cable and mounting hardware. PING))) is ideal for use with Raspberry Pi and Arduino based robot projects. PING))) ultrasonic range sensor kit. The PING))) ultrasonic sensor is perfect for applications that require you to perform distance measurements between moving or stationary objects. The sensor measures distance using sonar: an ultrasonic (well above human hearing) pulse is transmitted from the unit and distance-to-target is determined by measuring the time required for the echo return. Output from the PING))) sensor is a variable-width pulse that corresponds to the distance to the target. When coupled with the servomotor in this kit, the PING))) sensor can make a 180° scan of its environment and an obstacle map created. Together they're great for autonomous navigation. Servo motor can sweep the sensor through 180° Ideal for mobile robot navigation PING))) provides precise, non-contact distance measurement within a 2cm to 3m range Simple pulse in/pulse out communication on single GPIO pin Burst indicator LED shows measurement in progress
1 products found
JPY: 16,500
USD: 103.43
-
Parallax Inc 555-28027, PIR Sensor Module 555-28027
The product information found on this page currently pertains to Revision B of this product, which provides many updates and new features from Revision A. PIR (Passive Infra-Red) sensor module. The PIR (Passive Infra-Red) Sensor is a pyroelectric device that detects motion by measuring changes in the infrared (heat) levels emitted by surrounding objects. When motion is detected the PIR Sensor outputs a high signal on its output pin. This logic signal can be read by a microcontroller or used to drive an external load. Detect a person up to 10 m away, or up to 5 m in reduced sensitivity mode Jumper selects normal operation or reduced sensitivity Supply current up to 12 mA @ +3 V, 23mA @ +5 V Onboard LEDs light up the lens for fast visual feedback when movement is detected Mounting holes for 2-56 sized screws 3-pin SIP header ready for breadboard or through-hole projects Small size makes it easy to conceal Easy interface to any microcontroller Power requirement: +3 to +6 Vdc, 130 μA idle, 23 mA active (no load) Communication: Single-bit high/low output Dimensions: 35.8 x 25.4 x 20.3 mm Operating temperature range: 0 to +50°C
1 products found
JPY: 3,840
USD: 24.07
-
Parallax Inc Servo Motor, 4 → 6 V, 0 → 50 rpm 900-00008
Assortment of servo horns. R/C servo motor, continuous rotation. The Parallax Continuous Rotation Servomotor is ideal for prototyping mobile (wheeled) robots. It is easily interfaced with any microcontroller able to produce a 50Hz PWM output. Bidirectional continuous rotation. 0 to 50rpm, with linear response to PWM for easy speed ramping. Trim pot to set motor stop. Torque: 38oz-in @ +6V. Standard R/C (hobby) servo mounting and 3-pin connector. Power supply: +4 to +6Vdc, 15 to 200mA. Operating temperature range: -10 to +50°C. Dimensions: 55.8 x 19 x 40.6mm excluding servo horn. Weight: 42.5g
1 products found
JPY: 4,880
USD: 30.59
-
Parallax Inc P8X32A-D40, 32bit P8X32A Microcontroller, 80MHz, 64 kB ROM, 40-Pin PDIP P8X32A-D40
Propeller 1 Microcontrollers. The Parallax P8X32A (Propeller) is an 8-core 32-bit microprocessor designed to provide high-speed processing for embedded systems.It is available in two package formats: 40-pin DIP and 44-pin QFP SMT. Ideal for real-time control applications because the task switching between cores is fully deterministic. Clock frequency: up to 80MHz Performance: up to 160MIPS No of cores (COGs): 8 Global ROM: 32KB Global RAM: 32KB COG RAM: 2KB each 32 x GPIO pins 2 x multi-function counters/COG 1 x Video generator/COG Power supply: +2.7 to +3.6Vdc Operating temperature range: -55 to +125°C RS Product Codes ; 405-597 405-597 P8X32A-D40 Propeller, DIP40 ; 405-626 405-626 P8X32A-Q44 Propeller, QFP44
1 products found
JPY: 24,700
USD: 154.83
-
Parallax Inc P8X32A-Q44, 32bit P8X32A Microcontroller, 80MHz, 64 kB ROM, 44-Pin LQFP P8X32A-Q44
Propeller 1 Microcontrollers. The Parallax P8X32A (Propeller) is an 8-core 32-bit microprocessor designed to provide high-speed processing for embedded systems.It is available in two package formats: 40-pin DIP and 44-pin QFP SMT. Ideal for real-time control applications because the task switching between cores is fully deterministic. Clock frequency: up to 80MHz Performance: up to 160MIPS No of cores (COGs): 8 Global ROM: 32KB Global RAM: 32KB COG RAM: 2KB each 32 x GPIO pins 2 x multi-function counters/COG 1 x Video generator/COG Power supply: +2.7 to +3.6Vdc Operating temperature range: -55 to +125°C RS Product Codes ; 405-597 405-597 P8X32A-D40 Propeller, DIP40 ; 405-626 405-626 P8X32A-Q44 Propeller, QFP44
1 products found
JPY: 354,000
USD: 2,219.02
-
[Discontinued]Parallax Inc 27911, 3-axis Gyroscope Sensor Module 27911
3-axis gyroscope module. The Gyroscope Module is a low power 3-axis angular rate sensor featuring temperature data as an added bonus. Raw measured angular rate and temperature data are accessed from the selectable digital interface (I2C or SPI). The module features a small package design and has an easy to access SIP interface with a mounting hole for quick connectivity to your projects. It is designed for use with a large variety of microcontrollers with different voltage requirements. 3-axis angular rate sensor (yaw, pitch and roll) Supports I2C and SPI communications Three selectable scales: 250/500/2000 degrees/sec (dps) High shock survivability Embedded temperature sensor: -40 to +85°C Power-down and sleep mode 16-bit rate value data output 8-bit temperature data output Power requirement: 2.7 to 6.5Vdc Communication: I2C (up to 400kHz) or SPI (10MHz, 4 & 3 wire) Operating temperature range: -40 to +85°C Dimensions: 21.6 x 20.3mm
1 products found
JPY: 6,780
USD: 42.50
-
[Discontinued]Parallax Inc 27979 Alphanumeric LCD Display, Black on Green, 4 Rows by 20 Characters, Transflective 27979
Parallax 20 x 4 serial backlit mono LCD display. The Parallax Serial LCDs are very functional, low-cost liquid crystal displays that can be easily interfaced to and controlled by a microcontroller using a I/O pin. Code examples are included for the BASIC Stamp® and Propeller™ chip. The LCD displays provide basic text wrapping so that your text looks correct on the display. Full control over all of their advanced LCD features allows you to move the cursor anywhere on the display with a single instruction and turn the display on and off in any configuration. They support the same visible characters as the BASIC Stamp Editor's Debug Terminal (ASCII Dec 32-127). In addition, you may define up to eight of your own custom characters to display anywhere on the LCD. Clear 4 line x 20 character display Turn backlighting on or off with a single command Directly supports ASCII DEC characters 32-127 Eight user-definable custom characters Move the cursor anywhere on the display with a single command Baud mode selector and adjustable contrast on the back of the display Power requirement: +5Vdc, 20mA (light off), 80mA (light on) Selectable UART serial baud rates: 2400, 9600, 19200 Dimensions: 60.2 x 98.1mm Operating temp range: -20 to +70°C
1 products found
JPY: 9,380
USD: 58.80
-
[Discontinued]Parallax Inc 140 mA Servo Motor, 4 → 6 V 900-00005
R/C servo motor, standard 180deg. The Parallax Standard Servomotor is ideal for prototyping robot arm and animatronic applications. It can hold any position over a 180° range and is easily interfaced with any microcontroller able to produce a 50Hz PWM output. High-precision gears made of polyacetal resin for smooth operation with no backlash. Torque: 38 oz-in @ +6V. Standard R/C (hobby) servo mounting and 3-pin connector. Power supply: +4V to +6Vdc, 15 to 200mA. Operating temperature range: -10 to +50°C. Dimensions: 55.8 x 19 x 40.6mm excluding servo horn. Weight: 44g
1 products found
JPY: 2,300
USD: 14.42
-
[Discontinued]Parallax Inc 2-Axis Joystick Module 27800
2-axis analogue joystick module. This 2-Axis Joystick can be used to add analogue input to your next project. The 2-Axis Joystick contains two independent potentiometers (one per axis) for reporting the joystick's position, with wiring options for voltage or resistance outputs.The modular form-factor allows you to plug the 2-Axis Joystick directly into a breadboard for easy prototyping. The 2-Axis Joystick includes spring auto return to centre and a comfortable cup-type knob. Easy breadboard connection Two independent 10K potentiometers with common ground Spring auto return to centre Comfortable cup-type knob Power: 0.01W Dimensions: 41.67 x 35.56 x 27.94mm Operating temperature range: 0 to +70°C
1 products found
JPY: 1,820
USD: 11.41
-
[Discontinued]Parallax Inc 32213, X-Band Motion Sensor Module 32213
X-Band motion detector module. The X-Band Motion Detector operates in the X-band frequency of 10.525GHz and indicates detected movements with oscillations in its high/low output. The X-Band Motion Detector's sensor is a common ingredient in security systems and automatic door openers, and can detect movements in a room, yard, or even on the other side of a wall. Sensitivity is manually adjustable with a potentiometer, offering direct line of sight detection from roughly 2.4 to 9m. Operating frequency: 10.525GHz Less prone to false triggers than passive infrared (PIR) motion sensors Active-high enable pin with internal pull-up resistor Trim potentiometer for manually adjustable sensitivity 4-Pin SIP header for breadboard or through-hole prototyping Built-in series resistor for compatibility with the Propeller microcontroller and other 3.3V devices Plated test point hole for monitoring pre-comparator signal Power supply requirement: regulated 5Vdc @ 8mA Communication: High (3.9V) / low (0V) signal oscillates with motion Dimensions: 46 x 45 x 19mm Operating temperature range: 0 to +55°C
1 products found
JPY: 9,110
USD: 57.11
-
[Discontinued]Parallax Inc, DC Motor Controller, 3 Phase, 7.4 → 11.1 V dc, 30 A 750-90000
GemFan 30A BLDC motor speed controller. Electronic Speed Controllers (ESCs) are used on most R/C equipment for controlling the speed of a brushless DC motor. Compatible with a standard R/C receiver or any 3.3V or 5V microcontroller providing a standard PWM servomotor control signal. Programmable with an ESC programming card 5V Battery Eliminator Circuit (BEC) Three-phase electronic control of BLDC motor Two (2S) or three (3S) cell Li Polymer battery input Power requirements: 7.4 to 11.1Vdc Continuous maximum current: 30A Communication: R/C servo PWM Dimensions: 48.26 x 25.4 x 7.62mm Weight: 27g
1 products found
JPY: 2,220
USD: 13.92

