[Igus]Power Transmission - Rotary Bearings
Filters
-
Pedestal Bearing KSTM-08, 8mm ID KSTM-08
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free Pedestal Bearings. Easy to install pedestal bearings compensate for alignment errors and avoid edge pressures. The housings are manufactured from an impact resistant, rigid, thermoplastic composite material. High sliding speeds of up to 1.5m/s for rotary movements and 8m/s for linear movements can be supported
1 products found
JPY: 1,520
USD: 9.46
-
Pedestal Bearing KSTM-10, 10mm ID KSTM-10
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free Pedestal Bearings. Easy to install pedestal bearings compensate for alignment errors and avoid edge pressures. The housings are manufactured from an impact resistant, rigid, thermoplastic composite material. High sliding speeds of up to 1.5m/s for rotary movements and 8m/s for linear movements can be supported
1 products found
JPY: 1,470
USD: 9.15
-
Pedestal Bearing KSTM-12, 12mm ID KSTM-12
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free Pedestal Bearings. Easy to install pedestal bearings compensate for alignment errors and avoid edge pressures. The housings are manufactured from an impact resistant, rigid, thermoplastic composite material. High sliding speeds of up to 1.5m/s for rotary movements and 8m/s for linear movements can be supported
1 products found
JPY: 1,730
USD: 10.76
-
Pedestal Bearing KSTM-16, 16mm ID KSTM-16
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free Pedestal Bearings. Easy to install pedestal bearings compensate for alignment errors and avoid edge pressures. The housings are manufactured from an impact resistant, rigid, thermoplastic composite material. High sliding speeds of up to 1.5m/s for rotary movements and 8m/s for linear movements can be supported
1 products found
JPY: 2,920
USD: 18.17
-
Pedestal Bearing KSTM-20, 20mm ID KSTM-20
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free Pedestal Bearings. Easy to install pedestal bearings compensate for alignment errors and avoid edge pressures. The housings are manufactured from an impact resistant, rigid, thermoplastic composite material. High sliding speeds of up to 1.5m/s for rotary movements and 8m/s for linear movements can be supported
1 products found
JPY: 3,580
USD: 22.28
-
2 Hole Flanged Bearing, EFOM-12, 12mm ID EFOM-12
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Flange Bearings. Spherical two bolt flange bearings compensate for alignment errors and avoid edge pressures Radial load 950N – 3000N
1 products found
JPY: 2,390
USD: 14.87
-
2 Hole Flanged Bearing, EFOM-16, 16mm ID EFOM-16
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Flange Bearings. Spherical two bolt flange bearings compensate for alignment errors and avoid edge pressures Radial load 950N – 3000N
1 products found
JPY: 2,650
USD: 16.49
-
2 Hole Flanged Bearing, EFOM-20, 20mm ID EFOM-20
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Flange Bearings. Spherical two bolt flange bearings compensate for alignment errors and avoid edge pressures Radial load 950N – 3000N
1 products found
JPY: 4,370
USD: 27.19
-
4 Hole Flanged Bearing, EFSM-10, 10mm ID EFSM-10
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 4 Bolt Flange Bearing. Maximum loading up to 4000N dependant on size
1 products found
JPY: 2,000
USD: 12.44
-
2 Hole Flanged Bearing, GFL-10, 10mm ID GFL-10
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Plain Bearing. These very low height plain bearings can be used with rotating, oscillating and axial movements. They are maintenance free and abrasion, temperature and corrosion resistant. E10 tolerance on inside diameter (measured with plug gauge) Fit into a H7 bore for high load applications Can be used with a simple punched hole for most applications Temperatures from -40°C to +220°C (short term), 130°C (long term) possible Maintenance free, self lubricating Ideal in dirty dusty conditions
1 products found
JPY: 1,170
USD: 7.28
-
2 Hole Flanged Bearing, GFL-12, 12mm ID GFL-12
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Plain Bearing. These very low height plain bearings can be used with rotating, oscillating and axial movements. They are maintenance free and abrasion, temperature and corrosion resistant. E10 tolerance on inside diameter (measured with plug gauge) Fit into a H7 bore for high load applications Can be used with a simple punched hole for most applications Temperatures from -40°C to +220°C (short term), 130°C (long term) possible Maintenance free, self lubricating Ideal in dirty dusty conditions
1 products found
JPY: 1,290
USD: 8.03
-
2 Hole Flanged Bearing, GFL-20, 20mm ID GFL-20
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Plain Bearing. These very low height plain bearings can be used with rotating, oscillating and axial movements. They are maintenance free and abrasion, temperature and corrosion resistant. E10 tolerance on inside diameter (measured with plug gauge) Fit into a H7 bore for high load applications Can be used with a simple punched hole for most applications Temperatures from -40°C to +220°C (short term), 130°C (long term) possible Maintenance free, self lubricating Ideal in dirty dusty conditions
1 products found
JPY: 1,340
USD: 8.34
-
4 Hole Flanged Bearing, EFSM-08, 8mm ID EFSM-08
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 4 Bolt Flange Bearing. Maximum loading up to 4000N dependant on size
1 products found
JPY: 1,730
USD: 10.76
-
4 Hole Flanged Bearing, EFSM-12, 12mm ID EFSM-12
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 4 Bolt Flange Bearing. Maximum loading up to 4000N dependant on size
1 products found
JPY: 2,520
USD: 15.68
-
4 Hole Flanged Bearing, EFSM-16, 16mm ID EFSM-16
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 4 Bolt Flange Bearing. Maximum loading up to 4000N dependant on size
1 products found
JPY: 2,930
USD: 18.23
-
4 Hole Flanged Bearing, EFSM-20, 20mm ID EFSM-20
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 4 Bolt Flange Bearing. Maximum loading up to 4000N dependant on size
1 products found
JPY: 4,380
USD: 27.25
-
2 Hole Flanged Bearing, GFL-16, 16mm ID GFL-16
IGUBAL® bearings are designed to run with a clearance between the shaft and the inside diameter of the ball, to prevent the ball turning in the housing. IGUS® Maintenance Free 2 Bolt Plain Bearing. These very low height plain bearings can be used with rotating, oscillating and axial movements. They are maintenance free and abrasion, temperature and corrosion resistant. E10 tolerance on inside diameter (measured with plug gauge) Fit into a H7 bore for high load applications Can be used with a simple punched hole for most applications Temperatures from -40°C to +220°C (short term), 130°C (long term) possible Maintenance free, self lubricating Ideal in dirty dusty conditions
1 products found
JPY: 1,300
USD: 8.09
-
Igus Thrust Washer GTM-1018-010 GTM-1018-010
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,520
USD: 15.68
-
Igus Thrust Washer GTM-1524-015 GTM-1524-015
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,230
USD: 13.88
-
Igus Thrust Washer GTM-2036-015 GTM-2036-015
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,760
USD: 17.17
-
3mm Deep Groove Ball Bearing 10mm O.D BB-623-A500-70-ES
Xiros Single Row Deep Groove Ball Bearings. Standard ball bearing dimensions PEEK cage material Xirodur plastic race material No lubrication FDA compliant Resistant to chemicals and wash downs Use at temperatures up to 150°C Industries: medicine, chemistry, plant engineering, food etc.
1 products found
JPY: 15,200
USD: 94.57
-
6mm Deep Groove Ball Bearing 19mm O.D BB-626-A500-70-ES
Xiros Single Row Deep Groove Ball Bearings. Standard ball bearing dimensions PEEK cage material Xirodur plastic race material No lubrication FDA compliant Resistant to chemicals and wash downs Use at temperatures up to 150°C Industries: medicine, chemistry, plant engineering, food etc.
1 products found
JPY: 17,000
USD: 105.77
-
Igus Plain Bush JSM-1012-08 JSM-1012-08
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 2,500
USD: 15.56
-
Igus Plain Bush JFM-0608-04 JFM-0608-04
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 2,040
USD: 12.69
-
Igus Plain Bush JFM-1214-07 JFM-1214-07
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 1,720
USD: 10.70
-
Igus Plain Bush JFM-0810-05 JFM-0810-05
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 1,880
USD: 11.70
-
Igus Plain Bush JFM-1012-09 JFM-1012-09
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 1,790
USD: 11.14
-
Igus Plain Bush JFM-2023-11 JFM-2023-11
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 1,540
USD: 9.58
-
Igus Bearing Kit KIT-RS-L KIT-RS-L
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 58,300
USD: 362.74
-
Igus Bearing Kit KIT-RS-S KIT-RS-S
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 46,700
USD: 290.57
-
Igus Thrust Washer GTM-1224-015 GTM-1224-015
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,500
USD: 15.56
-
Igus Thrust Washer GTM-1630-015 GTM-1630-015
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,230
USD: 13.88
-
Igus Thrust Washer GTM-1426-015 GTM-1426-015
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,870
USD: 17.86
-
Igus Thrust Washer GTM-1832-015 GTM-1832-015
Appearance may differ from products illustrated. The kits contain bushes and thrust washers. Replacement bushes are available separately through the RS website. iglidur ;sup>® ;/sup> Bush Kits. Two kits of iglidur ;sup>® ;/sup> G dry bushes and thrust washers, offering cost-effective solutions for a variety of applications requiring compact, low-friction bearings. iglidur ;sup>® ;/sup> G is the 'all rounder' polymer bearing, having low friction, high wear resistance and high load capacity.. Small kit contains plain and flanged bearings; large kit contains plain, flanged and thrust bearings Maintenance free and highly wear resistant Tolerant of dusty or dirty environments High resistance to most chemicals, solvents ; lubricants Temperature range: -40 to +130°C
1 products found
JPY: 2,680
USD: 16.68
-
Igus Linear Plain Bearing Kit Box KITBOX-RS-J-L KITBOX-RS-J-L
The iglidur (R) J plain bearing is not suitable for use in environments where the maximum allowable surface pressure (35 MPa) is reached, where high pressure is applied, where short-term temperature increases occur (above 120 °C), or where low operating frequency and low cost bearings are sufficient.
iglidur (R) J Bush Kit1 products found
JPY: 37,200
USD: 231.46
-
Igus Plain Bush JSM-0203-03 JSM-0203-03
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 16,200
USD: 100.80
-
Igus Plain Bush JSM-0304-05 JSM-0304-05
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 7,470
USD: 46.48
-
Igus Plain Bush JSM-0405-04 JSM-0405-04
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 5,730
USD: 35.65
-
Igus Plain Bush JSM-0507-05 JSM-0507-05
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 6,380
USD: 39.70
-
Igus Plain Bush JSM-0810-08 JSM-0810-08
iglidur ;sup>® ;/sup> J plain bearings are not suitable for use where a maximum permissible surface pressure of 35 MPa may occur, where high pressures may be present, where there are short-term temperature increases (above 120°C), or applications where a low-cost bearing for occasional movement is required. iglidur ;sup>® ;/sup> J Bush Kits. iglidur ;sup>® ;/sup> J plain bearings may be used for long-life applications, and are also suitable for use with soft shafts. The iglidur ;sup>® ;/sup> J plain bearings are designed to provide the lowest coefficient of friction while running dry, and offer a low stick-slip tendency. Waterproof material Extremely low friction Can be used with stainless steel or anodised aluminium shafts Resistant to dirt and dust No lubrication required
1 products found
JPY: 2,510
USD: 15.62
