[Cynergy3]Automation & Control Gear
Filters
- by Product group
- by Product
Sort by:
-
GFS polypropylene float switch,100VA RSF34W100RF
UL/UL recognised for Canada. 1m long PVC 16//0.2 cable. Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. General Purpose High Power Float Switches. Side mounting switches consisting of a reed switch and pivoted actuator magnet encapsulated in a waterproof housing. Can be used for 'normally open' or 'normally closed' operation, depending on orientation All units WBS approved, product for use in hot and cold water Minimum liquid SG 0.8 Nitrile gasket Length: 94mm
1 products found
JPY: 6,850
USD: 42.62
-
PPS drop float switch w/seal gasket,N/C RSF16Y050TG
0.5m of PVC 16//0.2 cable (polypropylene and polysulfone ETFE) (PPS). Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Drop Float Switch. A unique design switch which keeps the pivot area free from the fluid making them ideal for use in hot drink vending machines etc. Drop float types for monitoring upper level and extended drop float types for monitoring lower level in a tank. Float positioned below the switch in N/C position Switch opens well before liquid level reaches the float pivot Polypropylene and PPS are WRAS approved, products for use in hot and cold water UL recognised (excludes 228-1964)
1 products found
JPY: 7,610
USD: 47.35
-
Internal PPS H float switch with gasket RSF46Y050TG
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 6,370
USD: 39.63
-
Internal PPS H float switch w/PVC cable RSF46Y100RG
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 9,790
USD: 60.91
-
PPS V float switch w/PVC cable,1m N/O RSF56Y100RB
The cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the Vertical type the mounting thread and cable entry must be above the highest level of the liquid. epoxy sealed leadouts. Part numbers ending in '1/8' have a 1/8"NPT mounting thread Part numbers ending in 'C' have an M12 mounting thread. Cynergy3 RSF50 Series Float Switches. Cynergy3 RSF50 float switches are compact devices suitable for vending machines printing system and chemical dosing equipment, for example. RSF50 float switches are vertically mounted and feature a single switch. There is a range of different material options available within the RSF50 series so you will be sure to find a suitable float switch for more commonly used liquids. The direction of the switch can be reversed by firstly removing the float, inverting the switch and re-fitting it to the stem.. Within the series there are 5 ranges: RSF53 (black) - Nylon RSF54 (opaque) - Polypropylene (WRAS approved) RSF56 (grey) - Polyphenylene Sulphide (PPS) RSF57 (green) - Polyvinylidene Fluoride (PVDF) RSF58 (white) - Polypropylene (UL approved) Note - the different ranges feature other differences. Please refer to the Datasheet for more information on technical specifications. What contact types are there? The RSF50 float switches can be configured for N/O (Normally Open) or N/C (Normally Closed) operation. What mounting thread does it have? RSF50 float switches have either M12 or 1/8 NPT mounting thread. This is depicted by the last part of the part number. If it ends in B or C , it is an M12. If it ends in 1/8 it is 1/8 NPT.
1 products found
JPY: 9,150
USD: 56.93
-
Dual point vertical float switch,25&75mm RSF66A25B75
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. UL recognised. Cynergy3 RSF66 Single Float Switches. The Cynergy3 RSF66 single switch point series are float switches for high and low level switching. The RSF66 float switches are made using Polyphenylene Sulphide (PPS) in grey, which is ideal for a wide range of different liquids. This makes the RSF66 range versatile for different applications. Single float switches are typically used in systems that feature PLC process control. What length cable do they come with? The RSF66 series comes with a 1m standard cable length with flying lead. It is a four core PVC cable. What temperature can they withstand? -10°C to +85°C / +14°F to +185°F What is their power capacity? RSF66 float switches have a power capacity of 25VA. Approvals: WRAS, UL and NSF approved. Versions Available (including upper/lower switch levels): ( ; 348-7983 348-7983 ) RSF66A25B75 - Single 30/75mm ( ; 348-7999 348-7999 ) RSF66A25B100 - Single 30/100mm ( ; 348-8009 348-8009 ) RSF66A25B125 - Single 30/125mm ( ; 348-8015 348-8015 ) RSF66A25B150 - Single 30/150mm ( ; 348-8021 348-8021 ) RSF66A25B175 - Single 30/175mm ( ; 446-2597 446-2597 ) RSF66B50B150 - Double 50/150mm Filling Control ( ; 446-2581 446-2581 ) RSF66B50B100 - Double 50/100mm Filling Control ( ; 446-2575 446-2575 ) RSF66A50A150 - Double 50/150mm Emptying Control ( ; 446-2569 446-2569 ) RSF66A50A100 - Double 50/100mm Emptying Control
1 products found
JPY: 12,700
USD: 79.02
-
Dualpoint vertical float switch,25&100mm RSF66A25B100
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. UL recognised. Cynergy3 RSF66 Single Float Switches. The Cynergy3 RSF66 single switch point series are float switches for high and low level switching. The RSF66 float switches are made using Polyphenylene Sulphide (PPS) in grey, which is ideal for a wide range of different liquids. This makes the RSF66 range versatile for different applications. Single float switches are typically used in systems that feature PLC process control. What length cable do they come with? The RSF66 series comes with a 1m standard cable length with flying lead. It is a four core PVC cable. What temperature can they withstand? -10°C to +85°C / +14°F to +185°F What is their power capacity? RSF66 float switches have a power capacity of 25VA. Approvals: WRAS, UL and NSF approved. Versions Available (including upper/lower switch levels): ( ; 348-7983 348-7983 ) RSF66A25B75 - Single 30/75mm ( ; 348-7999 348-7999 ) RSF66A25B100 - Single 30/100mm ( ; 348-8009 348-8009 ) RSF66A25B125 - Single 30/125mm ( ; 348-8015 348-8015 ) RSF66A25B150 - Single 30/150mm ( ; 348-8021 348-8021 ) RSF66A25B175 - Single 30/175mm ( ; 446-2597 446-2597 ) RSF66B50B150 - Double 50/150mm Filling Control ( ; 446-2581 446-2581 ) RSF66B50B100 - Double 50/100mm Filling Control ( ; 446-2575 446-2575 ) RSF66A50A150 - Double 50/150mm Emptying Control ( ; 446-2569 446-2569 ) RSF66A50A100 - Double 50/100mm Emptying Control
1 products found
JPY: 12,700
USD: 79.02
-
Dualpoint vertical float switch,25&125mm RSF66A25B125
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. UL recognised. Cynergy3 RSF66 Single Float Switches. The Cynergy3 RSF66 single switch point series are float switches for high and low level switching. The RSF66 float switches are made using Polyphenylene Sulphide (PPS) in grey, which is ideal for a wide range of different liquids. This makes the RSF66 range versatile for different applications. Single float switches are typically used in systems that feature PLC process control. What length cable do they come with? The RSF66 series comes with a 1m standard cable length with flying lead. It is a four core PVC cable. What temperature can they withstand? -10°C to +85°C / +14°F to +185°F What is their power capacity? RSF66 float switches have a power capacity of 25VA. Approvals: WRAS, UL and NSF approved. Versions Available (including upper/lower switch levels): ( ; 348-7983 348-7983 ) RSF66A25B75 - Single 30/75mm ( ; 348-7999 348-7999 ) RSF66A25B100 - Single 30/100mm ( ; 348-8009 348-8009 ) RSF66A25B125 - Single 30/125mm ( ; 348-8015 348-8015 ) RSF66A25B150 - Single 30/150mm ( ; 348-8021 348-8021 ) RSF66A25B175 - Single 30/175mm ( ; 446-2597 446-2597 ) RSF66B50B150 - Double 50/150mm Filling Control ( ; 446-2581 446-2581 ) RSF66B50B100 - Double 50/100mm Filling Control ( ; 446-2575 446-2575 ) RSF66A50A150 - Double 50/150mm Emptying Control ( ; 446-2569 446-2569 ) RSF66A50A100 - Double 50/100mm Emptying Control
1 products found
JPY: 13,300
USD: 82.75
-
Dualpoint vertical float switch,25&150mm RSF66A25B150
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. UL recognised. Cynergy3 RSF66 Single Float Switches. The Cynergy3 RSF66 single switch point series are float switches for high and low level switching. The RSF66 float switches are made using Polyphenylene Sulphide (PPS) in grey, which is ideal for a wide range of different liquids. This makes the RSF66 range versatile for different applications. Single float switches are typically used in systems that feature PLC process control. What length cable do they come with? The RSF66 series comes with a 1m standard cable length with flying lead. It is a four core PVC cable. What temperature can they withstand? -10°C to +85°C / +14°F to +185°F What is their power capacity? RSF66 float switches have a power capacity of 25VA. Approvals: WRAS, UL and NSF approved. Versions Available (including upper/lower switch levels): ( ; 348-7983 348-7983 ) RSF66A25B75 - Single 30/75mm ( ; 348-7999 348-7999 ) RSF66A25B100 - Single 30/100mm ( ; 348-8009 348-8009 ) RSF66A25B125 - Single 30/125mm ( ; 348-8015 348-8015 ) RSF66A25B150 - Single 30/150mm ( ; 348-8021 348-8021 ) RSF66A25B175 - Single 30/175mm ( ; 446-2597 446-2597 ) RSF66B50B150 - Double 50/150mm Filling Control ( ; 446-2581 446-2581 ) RSF66B50B100 - Double 50/100mm Filling Control ( ; 446-2575 446-2575 ) RSF66A50A150 - Double 50/150mm Emptying Control ( ; 446-2569 446-2569 ) RSF66A50A100 - Double 50/100mm Emptying Control
1 products found
JPY: 16,000
USD: 99.55
-
Var insertion depth V float switch,N/C RSF64BEXS
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. ; 211-985 211-985 - N/O Contact ; 348-8037 348-8037 - N/C Contact. Variable Insertion Depth Vertical Float Switch. A vertical float switch with N/O or N/C switching action. Its overall depth and position can be adjusted. N/O Version has Contacts Which are Open when the Tank is Empty, N/C Version has Contacts which are Closed when the Tank is Empty Overall Depth can be Varied Between 150mm and 450mm by Adjusting its Position in a Sliding Clamp Up to 3 Extension Units (306mm long) May Be Added to Provide Insertion Depths up to 1350mm (see accessories) Temperature Range; 0 to 75°C Switching Depth; 123-423mm Electrical Life; 5 x 10 ;sup>6 ;/sup> Operations Polypropylene Float, PPS Stem and PVC Class 7 Tube Material
1 products found
JPY: 16,900
USD: 105.15
-
Multi float level switch,100mm 2N/C RSF66B50B150
The Cable entry point must NOT under any circumstances be submerged: – On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. – On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. UL recognised. Cynergy3 RSF66 Double Float Switches. The Cynergy3 RSF66 dual switch point series are float switches for high and low level switching. The RSF66 float switches are made using Polyphenylene Sulphide (PPS) in grey, which is ideal for a wide range of different liquids. This makes the RSF66 range versatile for different applications. Dual float switches can be used to control filling or emptying tanks with electromechanical relays.. What length cable do they come with? The RSF66 series comes with a 1m standard cable length with flying lead. It is a four core PVC cable. What temperature can they withstand? -10°C to +85°C / +14°F to +185°F What is their power capacity? RSF66 float switches have a power capacity of 25VA. Approvals: WRAS, UL and NSF approved Versions Available (including upper/lower switch levels): ( ; 446-2597 446-2597 ) RSF66B50B150 - Double 50/150mm Filling Control ( ; 446-2581 446-2581 ) RSF66B50B100 - Double 50/100mm Filling Control ( ; 446-2575 446-2575 ) RSF66A50A150 - Double 50/150mm Emptying Control ( ; 446-2569 446-2569 ) RSF66A50A100 - Double 50/100mm Emptying Control ( ; 348-7983 348-7983 ) RSF66A25B75 - Single 30/75mm ( ; 348-7999 348-7999 ) RSF66A25B100 - Single 30/100mm ( ; 348-8009 348-8009 ) RSF66A25B125 - Single 30/125mm ( ; 348-8015 348-8015 ) RSF66A25B150 - Single 30/150mm ( ; 348-8021 348-8021 ) RSF66A25B175 - Single 30/175mm
1 products found
JPY: 14,800
USD: 92.09
-
Polypropylene drop float switch,N/C RSF14Y050RF
0.5m of PVC 16//0.2 cable (polypropylene and polysulfone ETFE) (PPS). Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Drop Float Switch. A unique design switch which keeps the pivot area free from the fluid making them ideal for use in hot drink vending machines etc. Drop float types for monitoring upper level and extended drop float types for monitoring lower level in a tank. Float positioned below the switch in N/C position Switch opens well before liquid level reaches the float pivot Polypropylene and PPS are WRAS approved, products for use in hot and cold water UL recognised (excludes 228-1964)
1 products found
JPY: 9,520
USD: 59.23
-
External PPS H float switch w/cable,0.5m RSF76Y050TV
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 6,660
USD: 41.44
-
PPS V float switch w/ETFE cable,0.5m N/O RSF56Y050TB
The cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the Vertical type the mounting thread and cable entry must be above the highest level of the liquid. epoxy sealed leadouts. Part numbers ending in '1/8' have a 1/8"NPT mounting thread Part numbers ending in 'C' have an M12 mounting thread. Cynergy3 RSF50 Series Float Switches. Cynergy3 RSF50 float switches are compact devices suitable for vending machines printing system and chemical dosing equipment, for example. RSF50 float switches are vertically mounted and feature a single switch. There is a range of different material options available within the RSF50 series so you will be sure to find a suitable float switch for more commonly used liquids. The direction of the switch can be reversed by firstly removing the float, inverting the switch and re-fitting it to the stem.. Within the series there are 5 ranges: RSF53 (black) - Nylon RSF54 (opaque) - Polypropylene (WRAS approved) RSF56 (grey) - Polyphenylene Sulphide (PPS) RSF57 (green) - Polyvinylidene Fluoride (PVDF) RSF58 (white) - Polypropylene (UL approved) Note - the different ranges feature other differences. Please refer to the Datasheet for more information on technical specifications. What contact types are there? The RSF50 float switches can be configured for N/O (Normally Open) or N/C (Normally Closed) operation. What mounting thread does it have? RSF50 float switches have either M12 or 1/8 NPT mounting thread. This is depicted by the last part of the part number. If it ends in B or C , it is an M12. If it ends in 1/8 it is 1/8 NPT.
1 products found
JPY: 6,610
USD: 41.13
-
External mount polyprop H float switch RSF74Y100RN
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 5,350
USD: 33.29
-
Nylon V floatswitch with gasket,25VA N/O RSF53Y100RC
The cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the Vertical type the mounting thread and cable entry must be above the highest level of the liquid. epoxy sealed leadouts. Part numbers ending in '1/8' have a 1/8"NPT mounting thread Part numbers ending in 'C' have an M12 mounting thread. Cynergy3 RSF50 Series Float Switches. Cynergy3 RSF50 float switches are compact devices suitable for vending machines printing system and chemical dosing equipment, for example. RSF50 float switches are vertically mounted and feature a single switch. There is a range of different material options available within the RSF50 series so you will be sure to find a suitable float switch for more commonly used liquids. The direction of the switch can be reversed by firstly removing the float, inverting the switch and re-fitting it to the stem.. Within the series there are 5 ranges: RSF53 (black) - Nylon RSF54 (opaque) - Polypropylene (WRAS approved) RSF56 (grey) - Polyphenylene Sulphide (PPS) RSF57 (green) - Polyvinylidene Fluoride (PVDF) RSF58 (white) - Polypropylene (UL approved) Note - the different ranges feature other differences. Please refer to the Datasheet for more information on technical specifications. What contact types are there? The RSF50 float switches can be configured for N/O (Normally Open) or N/C (Normally Closed) operation. What mounting thread does it have? RSF50 float switches have either M12 or 1/8 NPT mounting thread. This is depicted by the last part of the part number. If it ends in B or C , it is an M12. If it ends in 1/8 it is 1/8 NPT.
1 products found
JPY: 5,180
USD: 32.23
-
Polyprop V floatswitch w/gasket,25VA N/O RSF54Y100RC
The cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the Vertical type the mounting thread and cable entry must be above the highest level of the liquid. epoxy sealed leadouts. Part numbers ending in '1/8' have a 1/8"NPT mounting thread Part numbers ending in 'C' have an M12 mounting thread. Cynergy3 RSF50 Series Float Switches. Cynergy3 RSF50 float switches are compact devices suitable for vending machines printing system and chemical dosing equipment, for example. RSF50 float switches are vertically mounted and feature a single switch. There is a range of different material options available within the RSF50 series so you will be sure to find a suitable float switch for more commonly used liquids. The direction of the switch can be reversed by firstly removing the float, inverting the switch and re-fitting it to the stem.. Within the series there are 5 ranges: RSF53 (black) - Nylon RSF54 (opaque) - Polypropylene (WRAS approved) RSF56 (grey) - Polyphenylene Sulphide (PPS) RSF57 (green) - Polyvinylidene Fluoride (PVDF) RSF58 (white) - Polypropylene (UL approved) Note - the different ranges feature other differences. Please refer to the Datasheet for more information on technical specifications. What contact types are there? The RSF50 float switches can be configured for N/O (Normally Open) or N/C (Normally Closed) operation. What mounting thread does it have? RSF50 float switches have either M12 or 1/8 NPT mounting thread. This is depicted by the last part of the part number. If it ends in B or C , it is an M12. If it ends in 1/8 it is 1/8 NPT.
1 products found
JPY: 5,450
USD: 33.91
-
Cynergy3, 0.9 L/min Flow Controller, Cable, Relay FS15LF
Not to be used in any chlorinated liquids. Normally Open Flow Switch. Flow switch series from Cynergy3. These flow switches are reed switch based and can monitor the flow of liquids up to 10bar in pressure. This series of flow switches can be mounted horizontally or vertically and have minimal flow restriction. Flow switches are ideally used in water but can be used in weak acidic liquids. Mainly for use with hot or cold water, however they may also be used with a wide range of chemicals Pressure rating 150psi maximum Switching current 1A dc or ac (rms) Switching voltage 240V dc or ac (rms) Switching power 15W (15VA) resistive loads Operating temperature 85°C maximum Vertical or horizontal mounting Standard compression or push fit fittings WRAS approved for use in cold water Complete with a 250mm lead
1 products found
JPY: 7,120
USD: 44.30
-
PPS drop float switch w/ext PVC lead,N/C RSF26Y100RF
0.5m of PVC 16//0.2 cable (polypropylene and polysulfone ETFE) (PPS). Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Drop Float Switch. A unique design switch which keeps the pivot area free from the fluid making them ideal for use in hot drink vending machines etc. Drop float types for monitoring upper level and extended drop float types for monitoring lower level in a tank. Float positioned below the switch in N/C position Switch opens well before liquid level reaches the float pivot Polypropylene and PPS are WRAS approved, products for use in hot and cold water UL recognised (excludes 228-1964)
1 products found
JPY: 7,670
USD: 47.72
-
WRAS N/O cable float switch,10A MS10AW
Cynergy3 MS Series Float Switches. The Cynergy3 MS series of float switches are designed for large tanks, cisterns or reservoirs, and can be installed on submersible pumps. The MS float switches are capable of reaching 100m in depth. MS float switches come with a 5m PVC cable.. What is it made from? The flow switch case is made from blow-moulded HDPE (polyethylene). The unit is hermetically sealed. The cable is made from PVC and has a protective earth conductor. Part numbers ending with the letter U have PUR cables suitable for use in fuel oils. What temperatures can it operate in? All MS float switches operate from 0°C to +45°C / +32°F to 113°F. What contact types are there? The 5th digit of the part number represents the contact type: A - Normally Open (N/O) B - Nortmally Closed (N/C) C - Changeover (C/O) Approvals: MS float switches have UL, VDE and CENELEC approvals. Part numbers ending with a "W" are WRAS approved cable coverings. Versions Available: ( ; 205-6910 205-6910 ) MS10A ( ; 338-9801 338-9801 ) MS20A ( ; 338-9794 338-9794 ) MS10B ( ; 869-7609 869-7609 ) MS20C ( ; 379-4001 379-4001 ) MS10AW ( ; 379-4017 379-4017 ) MS10BW
1 products found
JPY: 18,100
USD: 112.62
-
WRAS N/C cable float switch,10A MS10BW
Cynergy3 MS Series Float Switches. The Cynergy3 MS series of float switches are designed for large tanks, cisterns or reservoirs, and can be installed on submersible pumps. The MS float switches are capable of reaching 100m in depth. MS float switches come with a 5m PVC cable.. What is it made from? The flow switch case is made from blow-moulded HDPE (polyethylene). The unit is hermetically sealed. The cable is made from PVC and has a protective earth conductor. Part numbers ending with the letter U have PUR cables suitable for use in fuel oils. What temperatures can it operate in? All MS float switches operate from 0°C to +45°C / +32°F to 113°F. What contact types are there? The 5th digit of the part number represents the contact type: A - Normally Open (N/O) B - Nortmally Closed (N/C) C - Changeover (C/O) Approvals: MS float switches have UL, VDE and CENELEC approvals. Part numbers ending with a "W" are WRAS approved cable coverings. Versions Available: ( ; 205-6910 205-6910 ) MS10A ( ; 338-9801 338-9801 ) MS20A ( ; 338-9794 338-9794 ) MS10B ( ; 869-7609 869-7609 ) MS20C ( ; 379-4001 379-4001 ) MS10AW ( ; 379-4017 379-4017 ) MS10BW
1 products found
JPY: 18,100
USD: 112.62
-
WRAS submerged N/O cable floatswitch,10A FFSMC10AW
The Water Fittings Regulations (or by-laws 2000 in Scotland) are national requirements for the design, installation and maintenance of plumbing systems, water fittings and water using appliances. These require that all materials and fittings that will come into contact with supply water should be approved under the Water Regulations Advisory Scheme (WRAS). FFSMC Series - WRAS Approved. Submerged type float switch for sewer and industrial waste systems and turbulent industrial fluids. Self cleaning switching element with 10 amp contacts, this makes the switch insensitive to condensation and humidity caused by fluctuations in temperature. Rounded moulding to prevent the accumulation of solids Insensitive to Humidity and Condensation Water Resistant up to a Depth of 100m Switch Horizontal ±15° of Horizontal Fitted with Internal Weight Fixing the Centre of Gravity and Rotation Close to the Cable Entry External Counterweight Supplied to Adjust the Pivot Position WRC Approved PVC Cable
1 products found
JPY: 49,200
USD: 306.12
-
1/2in NPT mount polyprop H float switch RSF84Y100R
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 4,650
USD: 28.93
-
Float switch wired S/S internal, 1/8 BSP SSF211X100
Cynergy3 SSF211 and SSF212 Horizontal Float Switches. From Cynergy3, the SSF211 series and SSF212 series are horizontal float switches. They operate in liquids with Specific Gravity (SG) of 0.8 or above. These float switches are constructed from a reed switch and pivoted actuator magnet. SSF211 and SSF212 switches feature an N/C (normally closed) contact. SSF211 float switches are designed for horizontal mounting within a tank. They are only suitable for applications where you have suitable access to the inside of the tank so that you can fit them. SSF212 float switches can be mounted from outside the tank and do not require access. Features ; Benefits. While supplied with an N/O contact, you can easily configure this to N/C (normally closed) by inverting the switch by 180° when you mount it. Instead of the float moving in a downwards direction as standard, it would move in an upwards direction away from the main body of the switch. These float switches feature a compact design at only 47 mm long. The stem is constructed from SS304 stainless steel while the float is made from SS316 stainless steel. This ensures that these limit switches are suitable for use in the most rugged environments. All SSF211 float switches are fitted with a 1 m long 17/0.10 (AWG22) cable. They can be fitted internally via a 1/8 BSP thread. SSF212 float switches are fitted with a 1 m long 17/0.10 (AWG22) cable, plug and socket or M12 socket. This varies by model. They can be externally fitted via a 1/2 NPT thread.
1 products found
JPY: 27,400
USD: 170.48
-
Float switch wired S/S external, 1/2 NPT SSF212X100
Cynergy3 SSF211 and SSF212 Horizontal Float Switches. From Cynergy3, the SSF211 series and SSF212 series are horizontal float switches. They operate in liquids with Specific Gravity (SG) of 0.8 or above. These float switches are constructed from a reed switch and pivoted actuator magnet. SSF211 and SSF212 switches feature an N/C (normally closed) contact. SSF211 float switches are designed for horizontal mounting within a tank. They are only suitable for applications where you have suitable access to the inside of the tank so that you can fit them. SSF212 float switches can be mounted from outside the tank and do not require access. Features ; Benefits. While supplied with an N/O contact, you can easily configure this to N/C (normally closed) by inverting the switch by 180° when you mount it. Instead of the float moving in a downwards direction as standard, it would move in an upwards direction away from the main body of the switch. These float switches feature a compact design at only 47 mm long. The stem is constructed from SS304 stainless steel while the float is made from SS316 stainless steel. This ensures that these limit switches are suitable for use in the most rugged environments. All SSF211 float switches are fitted with a 1 m long 17/0.10 (AWG22) cable. They can be fitted internally via a 1/8 BSP thread. SSF212 float switches are fitted with a 1 m long 17/0.10 (AWG22) cable, plug and socket or M12 socket. This varies by model. They can be externally fitted via a 1/2 NPT thread.
1 products found
JPY: 26,100
USD: 162.39
-
S/steel horizontal mount floatswitch,24V SSF213T050
Horizontal Float Miniature – Stainless Steel. Miniature horizontally mounted float switches that can be fitted internally to the side of the tank. 304 grade stainless steel construction makes them ideally suited for use in aggressive environments. Internal Mounting Version Requiring Access to Inside of Tank Miniature Design - Total Length Inside Tank is Only 54.5mm 1/8 BSP Mounting in a Maximum 10mm Wall Thickness High Temperature Operation (120°C) User Configurable N/O or N/C Operation by Rotating Through 180°
1 products found
JPY: 44,200
USD: 275.01
-
Multi float level switch,100mm 2N/O RSF66A50A150
The Cable entry point must NOT under any circumstances be submerged: – On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. – On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. UL recognised. Cynergy3 RSF66 Double Float Switches. The Cynergy3 RSF66 dual switch point series are float switches for high and low level switching. The RSF66 float switches are made using Polyphenylene Sulphide (PPS) in grey, which is ideal for a wide range of different liquids. This makes the RSF66 range versatile for different applications. Dual float switches can be used to control filling or emptying tanks with electromechanical relays.. What length cable do they come with? The RSF66 series comes with a 1m standard cable length with flying lead. It is a four core PVC cable. What temperature can they withstand? -10°C to +85°C / +14°F to +185°F What is their power capacity? RSF66 float switches have a power capacity of 25VA. Approvals: WRAS, UL and NSF approved Versions Available (including upper/lower switch levels): ( ; 446-2597 446-2597 ) RSF66B50B150 - Double 50/150mm Filling Control ( ; 446-2581 446-2581 ) RSF66B50B100 - Double 50/100mm Filling Control ( ; 446-2575 446-2575 ) RSF66A50A150 - Double 50/150mm Emptying Control ( ; 446-2569 446-2569 ) RSF66A50A100 - Double 50/100mm Emptying Control ( ; 348-7983 348-7983 ) RSF66A25B75 - Single 30/75mm ( ; 348-7999 348-7999 ) RSF66A25B100 - Single 30/100mm ( ; 348-8009 348-8009 ) RSF66A25B125 - Single 30/125mm ( ; 348-8015 348-8015 ) RSF66A25B150 - Single 30/150mm ( ; 348-8021 348-8021 ) RSF66A25B175 - Single 30/175mm
1 products found
JPY: 15,100
USD: 93.95
-
LM10A NO compact cable float switch LM10A
LM10A and LM10B both have a protective earth, LM10C does not. LM Cable Float Switch (Submerged). Suitable for use in sewage and industrial waste water, and where there is a wide variation in temperature. Ideal for use in confined spaces due to its compact design. Internal Ballast Insensitive to Humidity and Condensation Adjustable Counterweight Specific Gravity of Liquid: 0.6 IP68 Sealed to Withstand 10 Bar High Density Polyethylene Casing (PEHD) 100m Depth Capacity Overall Size 129 x 75mm Diameter
1 products found
JPY: 42,100
USD: 261.95
-
LM10C CO compact cable float switch LM10C
LM10A and LM10B both have a protective earth, LM10C does not. LM Cable Float Switch (Submerged). Suitable for use in sewage and industrial waste water, and where there is a wide variation in temperature. Ideal for use in confined spaces due to its compact design. Internal Ballast Insensitive to Humidity and Condensation Adjustable Counterweight Specific Gravity of Liquid: 0.6 IP68 Sealed to Withstand 10 Bar High Density Polyethylene Casing (PEHD) 100m Depth Capacity Overall Size 129 x 75mm Diameter
1 products found
JPY: 42,200
USD: 262.57
-
LM10B NC compact cable float switch LM10B
LM10A and LM10B both have a protective earth, LM10C does not. LM Cable Float Switch (Submerged). Suitable for use in sewage and industrial waste water, and where there is a wide variation in temperature. Ideal for use in confined spaces due to its compact design. Internal Ballast Insensitive to Humidity and Condensation Adjustable Counterweight Specific Gravity of Liquid: 0.6 IP68 Sealed to Withstand 10 Bar High Density Polyethylene Casing (PEHD) 100m Depth Capacity Overall Size 129 x 75mm Diameter
1 products found
JPY: 42,100
USD: 261.95
-
Float switch S/S external, 1/2 NPT SSF212XPL
Cynergy3 SSF211 and SSF212 Horizontal Float Switches. From Cynergy3, the SSF211 series and SSF212 series are horizontal float switches. They operate in liquids with Specific Gravity (SG) of 0.8 or above. These float switches are constructed from a reed switch and pivoted actuator magnet. SSF211 and SSF212 switches feature an N/C (normally closed) contact. SSF211 float switches are designed for horizontal mounting within a tank. They are only suitable for applications where you have suitable access to the inside of the tank so that you can fit them. SSF212 float switches can be mounted from outside the tank and do not require access. Features ; Benefits. While supplied with an N/O contact, you can easily configure this to N/C (normally closed) by inverting the switch by 180° when you mount it. Instead of the float moving in a downwards direction as standard, it would move in an upwards direction away from the main body of the switch. These float switches feature a compact design at only 47 mm long. The stem is constructed from SS304 stainless steel while the float is made from SS316 stainless steel. This ensures that these limit switches are suitable for use in the most rugged environments. All SSF211 float switches are fitted with a 1 m long 17/0.10 (AWG22) cable. They can be fitted internally via a 1/8 BSP thread. SSF212 float switches are fitted with a 1 m long 17/0.10 (AWG22) cable, plug and socket or M12 socket. This varies by model. They can be externally fitted via a 1/2 NPT thread.
1 products found
JPY: 39,300
USD: 244.53
-
S/steel high press topmount float switch SSF28X100
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. Stainless Steel High Pressure Float Switch – Vertical Mount. SSF28 series float switch has been designed to work at high pressures and can be vertically mounted within the tank. Suitable For Use in Pressurised Chambers Containing Liquid Chemicals or Food Processing Liquids Capable of Operation Up to 40 Bar Vertically Mounted in the Top or Bottom of the Tank Reversible Switching Action (N/O or N/C) 350mm, XLPE Cable 10mm Mounting Wall Thickness
1 products found
JPY: 32,900
USD: 204.70
-
S/steel high press sidemount floatswitch SSF29X100
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. Stainless Steel High Pressure Float Switch – Horizontal Mount. Side mount vertical float switches designed to achieve reliable switching at high pressures. The switch can be mounted to the side of the tank from the inside and is suitable for use in pressurised chambers containing liquid chemicals or food processing liquids. Capable of Operation up to 40 Bar Pressure Horizontally Mounting Reversible Switching Action (N/O or N/C) 350mm, XLPE Cable 10mm Max. Mounting Wall Thickness
1 products found
JPY: 40,600
USD: 252.61
-
S/steel 2 position float switch,25/75mm SSF67A25B75
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. All ratings in tech. spec. table are for resistive loads only. Dual Position Stainless Steel Float Switch. Designed to give the user a number of switching options to cater for a variety of system requirements. These switches are most suited for use with aggressive liquids and hygienic applications. Two Independent Switching Points Lower Float Make on Fall, and Upper Float Make on Rise Minimum Fluid SG: 0.80 Switch Differential (each level) Nominal: 1mm Suitable for High and Low Level Alarm and Control Signal Stainless Steel 316L for Use with Aggressive Liquids, or in Hygienic Applications Vertical Mounting, M16 x 2 Thread Temperature Range: -20 to +135°C Nitrile Gasket ‘Safe Area ‘ for Use in Petrochemical, Storage, and Process Control Applications
1 products found
JPY: 31,100
USD: 193.50
-
S/steel 2 position float switch,25/125mm SSF67A25B125
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. All ratings in tech. spec. table are for resistive loads only. Dual Position Stainless Steel Float Switch. Designed to give the user a number of switching options to cater for a variety of system requirements. These switches are most suited for use with aggressive liquids and hygienic applications. Two Independent Switching Points Lower Float Make on Fall, and Upper Float Make on Rise Minimum Fluid SG: 0.80 Switch Differential (each level) Nominal: 1mm Suitable for High and Low Level Alarm and Control Signal Stainless Steel 316L for Use with Aggressive Liquids, or in Hygienic Applications Vertical Mounting, M16 x 2 Thread Temperature Range: -20 to +135°C Nitrile Gasket ‘Safe Area ‘ for Use in Petrochemical, Storage, and Process Control Applications
1 products found
JPY: 61,800
USD: 384.52
-
S/steel 2 position float switch,25/175mm SSF67A25B175
The Cable entry point must NOT under any circumstances be submerged. On the Horizontal switches they must be fitted through the wall of a tank so that the cable is on the outside. On the vertical type the mounting thread and cable entry must be above the highest level of the liquid. All ratings in tech. spec. table are for resistive loads only. Dual Position Stainless Steel Float Switch. Designed to give the user a number of switching options to cater for a variety of system requirements. These switches are most suited for use with aggressive liquids and hygienic applications. Two Independent Switching Points Lower Float Make on Fall, and Upper Float Make on Rise Minimum Fluid SG: 0.80 Switch Differential (each level) Nominal: 1mm Suitable for High and Low Level Alarm and Control Signal Stainless Steel 316L for Use with Aggressive Liquids, or in Hygienic Applications Vertical Mounting, M16 x 2 Thread Temperature Range: -20 to +135°C Nitrile Gasket ‘Safe Area ‘ for Use in Petrochemical, Storage, and Process Control Applications
1 products found
JPY: 67,800
USD: 421.85
-
Cynergy3 EXT025M12PP Extension Tube, For Use With Vertical Plastic Switches EXT025M12PP
Outside diameter for thread size M12 x 1.75 is 16mm x 2 mm wall thickness Outside diameter for thread size M16 x 2 is 20 mm x 2.5 mm wall thickness. Extension Tubes. These extension tubes are ideal for extending the length of a variety of float switches. Ideal for use with the plastic type float switches. Extends the Reach of Various Float Switches Gaskets Made of Nitrile Polypropylene Extensions with M12 or M16 Thread
1 products found
JPY: 4,720
USD: 29.37
-
Float Switch Horizl Int Mnt 100W PPS RSF46H050TG
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 7,930
USD: 49.34
-
Float Switch Horizl Int Mnt 100W Nylon RSF43H100RF
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 6,030
USD: 37.52
-
Float Switch Horizl Int Mnt 100W PP RSF44H100RF
Suitable for signal switching and for use with transistorised input/low power, suppressed coil miniature relays. Not suited for any inductive or inrush (e.g. filament lamps) loads. Cynergy3 Horizontal Float Switches. Cynergy3 offers wide range of horizontal switches which are WRAS approved and have low-cost compact design. These horizontal float switches consist of a reed switch and a pivoted actuator magnet and can be used for N/O or N/C operation. The switch action can be reversed by mounting the float switch with the float able to move upwards away from the body instead of downwards. WRAS approval explained. WRAS is the standard against waste, misuse, undue consumption or contamination of the water supply and must have an appropriate quality and standard. What materials can you choose from?. Nylon Polypropylene Polypropylene Sulfide (PPS). Features and Benefits. Operating temperature: -10 °C to +120 °C N/O or N/C Switch output Switch action may be reversed by rotating the switch through 180º Choice of gasket materials: Silicone, Nitrile, Viton or combination of Silicone ; Nitrile Flying Lead M12 plug connection Internal ; external fitting inside a tank UL recognised. Typical Applications. These Cynergy3 Horizontal Switches are most likely to be used in vending machines, commercial washing machines and evaporator units.
1 products found
JPY: 5,820
USD: 36.21
