Makita Corporation

62-9807-46　［Discontinued］Air plasma cutting welder　APW60

Features

Air plasma cutting + welding (TIG welding and hand welding) 3 roles for 1 car!
Inverter Control * Rated Utilization ... Utilization is expressed in 10 minute cycles. Rated utilization rate of 60% means that the rated output current is applied for 6 minutes, and the temperature rise does not exceed the allowable temperature after resting for 4 minutes.
* The following items are required when using. Input Cable: 5.5 mm2 or more x 3 (Use 14 mm2 for 10 m or more), Ground Cable: 14 mm2 or more x 1, Air Compressor: Compressor 1.5 kW (2 horsepower or more) Pressure (Mpa): 0.39~0.96, Discharge: 165 L/min or more, Air Hose: Inner Diameter: φ6.5 mm, Hand Welded, TIG Welded

Spec

iron plate Detachable : 25 mm
iron plate Good Disconnect : 19 mm
[Main body]
power supply: Three Phase: Cutting, TIG, Hand Welding, Single Phase: Cutting, TIG, Hand Welding
rating input voltage (V): 3 phase: 200, 1 phase: 200
Input Voltage Tolerance: 3 Phase: 200 V ± 10%, Single Phase: 200 V ± 10%
rating Frequency (Hz): 50/60 three-phase, 50/60 single-phase.
[rating input (kVA)]
Three phases: cutting/13.3, TIG/7.5, hand welding/10.2
Single Phase: Cut/10.9, TIG/5.6, Hand Weld/7.8
[rating input (kW)]
Three phases: cutting/10.5, TIG/5.5, hand welding/7.7
Single Phase: Cut/8.0, TIG/3.5, Hand Weld/5.5
[rating output current (A)]
Three phases: cutting/60, TIG/200, hand welding/200
Single Phase: Cut/45, TIG/150, Hand Weld/150
[& Output current range]
Three-phase: Cutting/10 to 60, TIG/4 to 200, Hand welding/4 to 200
Single phase: Cutting/10 to 45, TIG/4 to 150, Hand welding/30 to 150
Initial current (A): same as output current range (Clatterfiller current range TIG Welding chisel)
rating Load Voltage (V): three-phase: cutting/140, TIG/18, hand-welded/28, single-phase: cutting/140, TIG/17, hand-welded/26
Maximum no-load voltage (V): three-phase: cutting/250, TIG/75, hand-welded/75; single-phase: cutting/250, TIG/75, hand-welded/75
rating Utilization%: Three-phase: Cutting/60, TIG/40, Hand welding/40, Single-phase: Cutting/40, TIG/40, Hand welding/40
Gas pre-flow time (S): 1.5 in cutting mode, 0.3 in TIG welding mode (0.6 seconds is possible by switching on the printed circuit board.)
Gas after-flow time (S): 10 (Fixed) in cutting mode, 3 to 30 (Variable) in TIG welding mode
Downslope time: (chisel during TIG welding) 0 to 5
Crater filler operation method: Yes/No/Iterative switching type (TIG Welded chisel)
Self-Retaining Function: Self-Retaining Yes/No/Switched (amputated chisel)
Mass (kg): 45
Format: DHCT0701 (Kabuto type)
Cooling method: air cooling
rated current: 70
rating% Utilization): 60
Cable length (m): 10
Air unit (Include in the power supply): DHP 9400 X
Standard Accessories: Glass Tube Fuse (5A, 10 A) Each 1 piece, Base Material Cable (1.5 m) 1 piece, Air Unit, Hose Band, indicator lamp, Cable bolt (1 Expression), Wrench (1 piece), insulation Cup (1 piece), H Tip (Three.), S Tip (Two.), Electrode (5 pieces)

Order No.	62-9807-46
Model No.	APW60
JAN Code	0088381010238
Standard price	JPY: 679,000 USD: 4,256.25 Excange rate 1USD= 159.53JPY Valid price in Japan
Quantity	1piece

Stock in Japan	-